1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2018 NXP 4 */ 5 6 #ifndef __LX2_COMMON_H 7 #define __LX2_COMMON_H 8 9 #include <asm/arch/stream_id_lsch3.h> 10 #include <asm/arch/config.h> 11 #include <asm/arch/soc.h> 12 13 #define CONFIG_REMAKE_ELF 14 #define CONFIG_FSL_LAYERSCAPE 15 #define CONFIG_GICV3 16 #define CONFIG_FSL_TZPC_BP147 17 #define CONFIG_FSL_MEMAC 18 19 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE 20 #define CONFIG_SYS_FLASH_BASE 0x20000000 21 22 #define CONFIG_SKIP_LOWLEVEL_INIT 23 #define CONFIG_BOARD_EARLY_INIT_F 1 24 25 /* DDR */ 26 #define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ 27 #define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ 28 #define CONFIG_VERY_BIG_RAM 29 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 30 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 31 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL 32 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 33 #define CONFIG_SYS_SDRAM_SIZE 0x200000000UL 34 #define CONFIG_DDR_SPD 35 #define CONFIG_DDR_ECC 36 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 37 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 38 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 39 #define SPD_EEPROM_ADDRESS1 0x51 40 #define SPD_EEPROM_ADDRESS2 0x52 41 #define SPD_EEPROM_ADDRESS3 0x53 42 #define SPD_EEPROM_ADDRESS4 0x54 43 #define SPD_EEPROM_ADDRESS5 0x55 44 #define SPD_EEPROM_ADDRESS6 0x56 45 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 46 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 47 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 48 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 49 #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ 50 #define CONFIG_SYS_MONITOR_LEN (936 * 1024) 51 52 /* Miscellaneous configurable options */ 53 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 54 55 /* SMP Definitinos */ 56 #define CPU_RELEASE_ADDR secondary_boot_func 57 58 /* Generic Timer Definitions */ 59 /* 60 * This is not an accurate number. It is used in start.S. The frequency 61 * will be udpated later when get_bus_freq(0) is available. 62 */ 63 64 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 65 66 /* Size of malloc() pool */ 67 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) 68 69 /* Serial Port */ 70 #define CONFIG_PL01X_SERIAL 71 #define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4) 72 #define CONFIG_SYS_SERIAL0 0x21c0000 73 #define CONFIG_SYS_SERIAL1 0x21d0000 74 #define CONFIG_SYS_SERIAL2 0x21e0000 75 #define CONFIG_SYS_SERIAL3 0x21f0000 76 /*below might needs to be removed*/ 77 #define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ 78 (void *)CONFIG_SYS_SERIAL1, \ 79 (void *)CONFIG_SYS_SERIAL2, \ 80 (void *)CONFIG_SYS_SERIAL3 } 81 #define CONFIG_BAUDRATE 115200 82 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 83 84 /* MC firmware */ 85 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 86 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 87 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 88 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 89 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 90 91 /* Define phy_reset function to boot the MC based on mcinitcmd. 92 * This happens late enough to properly fixup u-boot env MAC addresses. 93 */ 94 #define CONFIG_RESET_PHY_R 95 96 /* 97 * Carve out a DDR region which will not be used by u-boot/Linux 98 * 99 * It will be used by MC and Debug Server. The MC region must be 100 * 512MB aligned, so the min size to hide is 512MB. 101 */ 102 #ifdef CONFIG_FSL_MC_ENET 103 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024) 104 #endif 105 106 /* I2C bus multiplexer */ 107 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ 108 #define I2C_MUX_CH_DEFAULT 0x8 109 110 /* RTC */ 111 #define RTC 112 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ 113 114 /* EEPROM */ 115 #define CONFIG_ID_EEPROM 116 #define CONFIG_SYS_I2C_EEPROM_NXID 117 #define CONFIG_SYS_EEPROM_BUS_NUM 0 118 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 119 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 120 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 121 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 122 123 /* Qixis */ 124 #define CONFIG_FSL_QIXIS 125 #define CONFIG_QIXIS_I2C_ACCESS 126 #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 127 128 /* PCI */ 129 #ifdef CONFIG_PCI 130 #define CONFIG_SYS_PCI_64BIT 131 #define CONFIG_PCI_SCAN_SHOW 132 #endif 133 134 /* MMC */ 135 #ifdef CONFIG_MMC 136 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 137 #endif 138 139 /* SATA */ 140 141 #ifdef CONFIG_SCSI 142 #define CONFIG_SCSI_AHCI_PLAT 143 #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 144 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 145 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 146 #define CONFIG_SYS_SCSI_MAX_LUN 1 147 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 148 CONFIG_SYS_SCSI_MAX_LUN) 149 #endif 150 151 /* USB */ 152 #ifdef CONFIG_USB 153 #define CONFIG_HAS_FSL_XHCI_USB 154 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 155 #endif 156 157 /* FlexSPI */ 158 #ifdef CONFIG_NXP_FSPI 159 #define NXP_FSPI_FLASH_SIZE SZ_64M 160 #define NXP_FSPI_FLASH_NUM 1 161 #endif 162 163 #ifndef __ASSEMBLY__ 164 unsigned long get_board_sys_clk(void); 165 unsigned long get_board_ddr_clk(void); 166 #endif 167 168 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 169 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 170 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4) 171 172 #define CONFIG_HWCONFIG 173 #define HWCONFIG_BUFFER_SIZE 128 174 175 #define CONFIG_SYS_MMC_ENV_DEV 0 176 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 177 #define CONFIG_ENV_SECT_SIZE 0x20000 178 #define CONFIG_ENV_OFFSET 0x500000 179 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ 180 CONFIG_ENV_OFFSET) 181 182 /* Allow to overwrite serial and ethaddr */ 183 #define CONFIG_ENV_OVERWRITE 184 185 /* Monitor Command Prompt */ 186 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 187 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 188 sizeof(CONFIG_SYS_PROMPT) + 16) 189 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ 190 #define CONFIG_CMDLINE_EDITING 1 191 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 192 193 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 194 195 /* Initial environment variables */ 196 #define XSPI_MC_INIT_CMD \ 197 "env exists secureboot && " \ 198 "esbc_validate 0x20700000 && " \ 199 "esbc_validate 0x20740000 ;" \ 200 "fsl_mc start mc 0x20a00000 0x20e00000\0" 201 202 #define SD_MC_INIT_CMD \ 203 "mmc read 0x80000000 0x5000 0x800;" \ 204 "mmc read 0x80100000 0x7000 0x800;" \ 205 "env exists secureboot && " \ 206 "mmc read 0x80700000 0x3800 0x10 && " \ 207 "mmc read 0x80740000 0x3A00 0x10 && " \ 208 "esbc_validate 0x80700000 && " \ 209 "esbc_validate 0x80740000 ;" \ 210 "fsl_mc start mc 0x80000000 0x80100000\0" 211 212 #define EXTRA_ENV_SETTINGS \ 213 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 214 "ramdisk_addr=0x800000\0" \ 215 "ramdisk_size=0x2000000\0" \ 216 "fdt_high=0xa0000000\0" \ 217 "initrd_high=0xffffffffffffffff\0" \ 218 "fdt_addr=0x64f00000\0" \ 219 "kernel_start=0x1000000\0" \ 220 "kernelheader_start=0x7C0000\0" \ 221 "scriptaddr=0x80000000\0" \ 222 "scripthdraddr=0x80080000\0" \ 223 "fdtheader_addr_r=0x80100000\0" \ 224 "kernelheader_addr_r=0x80200000\0" \ 225 "kernel_addr_r=0x81000000\0" \ 226 "kernelheader_size=0x40000\0" \ 227 "fdt_addr_r=0x90000000\0" \ 228 "load_addr=0xa0000000\0" \ 229 "kernel_size=0x2800000\0" \ 230 "kernel_addr_sd=0x8000\0" \ 231 "kernelhdr_addr_sd=0x3E00\0" \ 232 "kernel_size_sd=0x1d000\0" \ 233 "kernelhdr_size_sd=0x10\0" \ 234 "console=ttyAMA0,38400n8\0" \ 235 BOOTENV \ 236 "mcmemsize=0x70000000\0" \ 237 XSPI_MC_INIT_CMD \ 238 "boot_scripts=lx2160ardb_boot.scr\0" \ 239 "boot_script_hdr=hdr_lx2160ardb_bs.out\0" \ 240 "scan_dev_for_boot_part=" \ 241 "part list ${devtype} ${devnum} devplist; " \ 242 "env exists devplist || setenv devplist 1; " \ 243 "for distro_bootpart in ${devplist}; do " \ 244 "if fstype ${devtype} " \ 245 "${devnum}:${distro_bootpart} " \ 246 "bootfstype; then " \ 247 "run scan_dev_for_boot; " \ 248 "fi; " \ 249 "done\0" \ 250 "scan_dev_for_boot=" \ 251 "echo Scanning ${devtype} " \ 252 "${devnum}:${distro_bootpart}...; " \ 253 "for prefix in ${boot_prefixes}; do " \ 254 "run scan_dev_for_scripts; " \ 255 "done;\0" \ 256 "boot_a_script=" \ 257 "load ${devtype} ${devnum}:${distro_bootpart} " \ 258 "${scriptaddr} ${prefix}${script}; " \ 259 "env exists secureboot && load ${devtype} " \ 260 "${devnum}:${distro_bootpart} " \ 261 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 262 "&& esbc_validate ${scripthdraddr};" \ 263 "source ${scriptaddr}\0" 264 265 #define XSPI_NOR_BOOTCOMMAND \ 266 "env exists mcinitcmd && env exists secureboot "\ 267 "&& esbc_validate 0x20780000; " \ 268 "env exists mcinitcmd && " \ 269 "fsl_mc lazyapply dpl 0x20d00000; " \ 270 "run distro_bootcmd;run xspi_bootcmd; " \ 271 "env exists secureboot && esbc_halt;" 272 273 #define SD_BOOTCOMMAND \ 274 "env exists mcinitcmd && mmcinfo; " \ 275 "mmc read 0x80001000 0x6800 0x800; " \ 276 "env exists mcinitcmd && env exists secureboot " \ 277 " && mmc read 0x80780000 0x3C00 0x10 " \ 278 "&& esbc_validate 0x80780000;env exists mcinitcmd " \ 279 "&& fsl_mc lazyapply dpl 0x80001000;" \ 280 "run distro_bootcmd;run sd_bootcmd;" \ 281 "env exists secureboot && esbc_halt;" 282 283 #define BOOT_TARGET_DEVICES(func) \ 284 func(USB, usb, 0) \ 285 func(MMC, mmc, 0) \ 286 func(SCSI, scsi, 0) 287 #include <config_distro_bootcmd.h> 288 289 #endif /* __LX2_COMMON_H */ 290