1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2018 NXP
4  */
5 
6 #ifndef __LS1012AFRWY_H__
7 #define __LS1012AFRWY_H__
8 
9 #include "ls1012a_common.h"
10 
11 /* Board Rev*/
12 #define BOARD_REV_A_B			0x0
13 #define BOARD_REV_C			0x00080000
14 #define BOARD_REV_MASK			0x001A0000
15 /* DDR */
16 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
17 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
18 #define SYS_SDRAM_SIZE_512		0x20000000
19 #define SYS_SDRAM_SIZE_1024		0x40000000
20 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
21 #define CONFIG_CMD_MEMINFO
22 #define CONFIG_CMD_MEMTEST
23 #define CONFIG_SYS_MEMTEST_START	0x80000000
24 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
25 
26 #ifndef CONFIG_SPL_BUILD
27 #undef BOOT_TARGET_DEVICES
28 #define BOOT_TARGET_DEVICES(func) \
29 	func(MMC, mmc, 0) \
30 	func(USB, usb, 0)
31 #endif
32 
33 #undef CONFIG_ENV_OFFSET
34 #define CONFIG_ENV_OFFSET              0x1D0000
35 #undef FSL_QSPI_FLASH_SIZE
36 #define FSL_QSPI_FLASH_SIZE            SZ_16M
37 #undef CONFIG_ENV_SECT_SIZE
38 #define CONFIG_ENV_SECT_SIZE		0x10000 /*64 KB*/
39 #undef CONFIG_ENV_SIZE
40 #define CONFIG_ENV_SIZE			0x10000 /*64 KB*/
41 
42 /*  MMC  */
43 #ifdef CONFIG_MMC
44 #define CONFIG_FSL_ESDHC
45 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
46 #endif
47 
48 #define CONFIG_PCIE1		/* PCIE controller 1 */
49 
50 #define CONFIG_PCI_SCAN_SHOW
51 
52 #undef CONFIG_EXTRA_ENV_SETTINGS
53 #define CONFIG_EXTRA_ENV_SETTINGS		\
54 	"verify=no\0"				\
55 	"fdt_high=0xffffffffffffffff\0"		\
56 	"initrd_high=0xffffffffffffffff\0"	\
57 	"fdt_addr=0x00f00000\0"			\
58 	"kernel_addr=0x01000000\0"		\
59 	"kernel_size_sd=0x16000\0"		\
60 	"kernelhdr_size_sd=0x10\0"		\
61 	"kernel_addr_sd=0x8000\0"		\
62 	"kernelhdr_addr_sd=0x4000\0"		\
63 	"kernelheader_addr=0x1fc000\0"		\
64 	"kernelheader_addr=0x1fc000\0"		\
65 	"scriptaddr=0x80000000\0"		\
66 	"scripthdraddr=0x80080000\0"		\
67 	"fdtheader_addr_r=0x80100000\0"		\
68 	"kernelheader_addr_r=0x80200000\0"	\
69 	"kernelheader_size=0x40000\0"		\
70 	"kernel_addr_r=0x81000000\0"		\
71 	"fdt_addr_r=0x90000000\0"		\
72 	"load_addr=0x96000000\0"		\
73 	"kernel_size=0x2800000\0"		\
74 	"kernelheader_size=0x40000\0"		\
75 	"console=ttyS0,115200\0"		\
76 	BOOTENV					\
77 	"boot_scripts=ls1012afrwy_boot.scr\0"	\
78 	"boot_script_hdr=hdr_ls1012afrwy_bs.out\0"	\
79 	"scan_dev_for_boot_part="		\
80 	     "part list ${devtype} ${devnum} devplist; "	\
81 	     "env exists devplist || setenv devplist 1; "	\
82 	     "for distro_bootpart in ${devplist}; do "		\
83 		  "if fstype ${devtype} "			\
84 		      "${devnum}:${distro_bootpart} "		\
85 		      "bootfstype; then "			\
86 		      "run scan_dev_for_boot; "	\
87 		  "fi; "			\
88 	      "done\0"				\
89 	"scan_dev_for_boot="				  \
90 		"echo Scanning ${devtype} "		  \
91 				"${devnum}:${distro_bootpart}...; "  \
92 		"for prefix in ${boot_prefixes}; do "	  \
93 			"run scan_dev_for_scripts; "	  \
94 		"done;"					  \
95 		"\0"					  \
96 	"boot_a_script="				  \
97 		"load ${devtype} ${devnum}:${distro_bootpart} "  \
98 			"${scriptaddr} ${prefix}${script}; "    \
99 		"env exists secureboot && load ${devtype} "     \
100 			"${devnum}:${distro_bootpart} "		\
101 			"${scripthdraddr} ${prefix}${boot_script_hdr} " \
102 			"&& esbc_validate ${scripthdraddr};"    \
103 		"source ${scriptaddr}\0"	  \
104 	"installer=load mmc 0:2 $load_addr "	\
105 		   "/flex_installer_arm64.itb; "	\
106 		   "bootm $load_addr#$board\0"	\
107 	"qspi_bootcmd=echo Trying load from qspi..;"	\
108 		"sf probe && sf read $load_addr "	\
109 		"$kernel_addr $kernel_size; env exists secureboot "	\
110 		"&& sf read $kernelheader_addr_r $kernelheader_addr "	\
111 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
112 		"bootm $load_addr#$board\0"	\
113 	"sd_bootcmd=echo Trying load from sd card..;"		\
114 		"mmcinfo; mmc read $load_addr "			\
115 		"$kernel_addr_sd $kernel_size_sd ;"		\
116 		"env exists secureboot && mmc read $kernelheader_addr_r "\
117 		"$kernelhdr_addr_sd $kernelhdr_size_sd "		\
118 		" && esbc_validate ${kernelheader_addr_r};"	\
119 		"bootm $load_addr#$board\0"
120 
121 #undef CONFIG_BOOTCOMMAND
122 #ifdef CONFIG_TFABOOT
123 #undef QSPI_NOR_BOOTCOMMAND
124 #define QSPI_NOR_BOOTCOMMAND "pfe stop; run distro_bootcmd; run sd_bootcmd; "\
125 			     "env exists secureboot && esbc_halt;"
126 #else
127 #define CONFIG_BOOTCOMMAND "pfe stop; run distro_bootcmd; run sd_bootcmd; "\
128 			   "env exists secureboot && esbc_halt;"
129 #endif
130 #define CONFIG_CMD_MEMINFO
131 #define CONFIG_CMD_MEMTEST
132 #define CONFIG_SYS_MEMTEST_START	0x80000000
133 #define CONFIG_SYS_MEMTEST_END		0x9fffffff
134 
135 #include <asm/fsl_secure_boot.h>
136 
137 #include <asm/fsl_secure_boot.h>
138 #endif /* __LS1012AFRWY_H__ */
139