1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Xilinx SPI driver
4 *
5 * Supports 8 bit SPI transfers only, with or w/o FIFO
6 *
7 * Based on bfin_spi.c, by way of altera_spi.c
8 * Copyright (c) 2015 Jagan Teki <jteki@openedev.com>
9 * Copyright (c) 2012 Stephan Linz <linz@li-pro.net>
10 * Copyright (c) 2010 Graeme Smecher <graeme.smecher@mail.mcgill.ca>
11 * Copyright (c) 2010 Thomas Chou <thomas@wytron.com.tw>
12 * Copyright (c) 2005-2008 Analog Devices Inc.
13 */
14
15 #include <config.h>
16 #include <common.h>
17 #include <dm.h>
18 #include <errno.h>
19 #include <malloc.h>
20 #include <spi.h>
21 #include <asm/io.h>
22 #include <wait_bit.h>
23
24 /*
25 * [0]: http://www.xilinx.com/support/documentation
26 *
27 * Xilinx SPI Register Definitions
28 * [1]: [0]/ip_documentation/xps_spi.pdf
29 * page 8, Register Descriptions
30 * [2]: [0]/ip_documentation/axi_spi_ds742.pdf
31 * page 7, Register Overview Table
32 */
33
34 /* SPI Control Register (spicr), [1] p9, [2] p8 */
35 #define SPICR_LSB_FIRST BIT(9)
36 #define SPICR_MASTER_INHIBIT BIT(8)
37 #define SPICR_MANUAL_SS BIT(7)
38 #define SPICR_RXFIFO_RESEST BIT(6)
39 #define SPICR_TXFIFO_RESEST BIT(5)
40 #define SPICR_CPHA BIT(4)
41 #define SPICR_CPOL BIT(3)
42 #define SPICR_MASTER_MODE BIT(2)
43 #define SPICR_SPE BIT(1)
44 #define SPICR_LOOP BIT(0)
45
46 /* SPI Status Register (spisr), [1] p11, [2] p10 */
47 #define SPISR_SLAVE_MODE_SELECT BIT(5)
48 #define SPISR_MODF BIT(4)
49 #define SPISR_TX_FULL BIT(3)
50 #define SPISR_TX_EMPTY BIT(2)
51 #define SPISR_RX_FULL BIT(1)
52 #define SPISR_RX_EMPTY BIT(0)
53
54 /* SPI Data Transmit Register (spidtr), [1] p12, [2] p12 */
55 #define SPIDTR_8BIT_MASK GENMASK(7, 0)
56 #define SPIDTR_16BIT_MASK GENMASK(15, 0)
57 #define SPIDTR_32BIT_MASK GENMASK(31, 0)
58
59 /* SPI Data Receive Register (spidrr), [1] p12, [2] p12 */
60 #define SPIDRR_8BIT_MASK GENMASK(7, 0)
61 #define SPIDRR_16BIT_MASK GENMASK(15, 0)
62 #define SPIDRR_32BIT_MASK GENMASK(31, 0)
63
64 /* SPI Slave Select Register (spissr), [1] p13, [2] p13 */
65 #define SPISSR_MASK(cs) (1 << (cs))
66 #define SPISSR_ACT(cs) ~SPISSR_MASK(cs)
67 #define SPISSR_OFF ~0UL
68
69 /* SPI Software Reset Register (ssr) */
70 #define SPISSR_RESET_VALUE 0x0a
71
72 #define XILSPI_MAX_XFER_BITS 8
73 #define XILSPI_SPICR_DFLT_ON (SPICR_MANUAL_SS | SPICR_MASTER_MODE | \
74 SPICR_SPE)
75 #define XILSPI_SPICR_DFLT_OFF (SPICR_MASTER_INHIBIT | SPICR_MANUAL_SS)
76
77 #ifndef CONFIG_XILINX_SPI_IDLE_VAL
78 #define CONFIG_XILINX_SPI_IDLE_VAL GENMASK(7, 0)
79 #endif
80
81 #define XILINX_SPISR_TIMEOUT 10000 /* in milliseconds */
82
83 /* xilinx spi register set */
84 struct xilinx_spi_regs {
85 u32 __space0__[7];
86 u32 dgier; /* Device Global Interrupt Enable Register (DGIER) */
87 u32 ipisr; /* IP Interrupt Status Register (IPISR) */
88 u32 __space1__;
89 u32 ipier; /* IP Interrupt Enable Register (IPIER) */
90 u32 __space2__[5];
91 u32 srr; /* Softare Reset Register (SRR) */
92 u32 __space3__[7];
93 u32 spicr; /* SPI Control Register (SPICR) */
94 u32 spisr; /* SPI Status Register (SPISR) */
95 u32 spidtr; /* SPI Data Transmit Register (SPIDTR) */
96 u32 spidrr; /* SPI Data Receive Register (SPIDRR) */
97 u32 spissr; /* SPI Slave Select Register (SPISSR) */
98 u32 spitfor; /* SPI Transmit FIFO Occupancy Register (SPITFOR) */
99 u32 spirfor; /* SPI Receive FIFO Occupancy Register (SPIRFOR) */
100 };
101
102 /* xilinx spi priv */
103 struct xilinx_spi_priv {
104 struct xilinx_spi_regs *regs;
105 unsigned int freq;
106 unsigned int mode;
107 unsigned int fifo_depth;
108 u8 startup;
109 };
110
xilinx_spi_probe(struct udevice * bus)111 static int xilinx_spi_probe(struct udevice *bus)
112 {
113 struct xilinx_spi_priv *priv = dev_get_priv(bus);
114 struct xilinx_spi_regs *regs = priv->regs;
115
116 priv->regs = (struct xilinx_spi_regs *)dev_read_addr(bus);
117
118 priv->fifo_depth = dev_read_u32_default(bus, "fifo-size", 0);
119
120 writel(SPISSR_RESET_VALUE, ®s->srr);
121
122 return 0;
123 }
124
spi_cs_activate(struct udevice * dev,uint cs)125 static void spi_cs_activate(struct udevice *dev, uint cs)
126 {
127 struct udevice *bus = dev_get_parent(dev);
128 struct xilinx_spi_priv *priv = dev_get_priv(bus);
129 struct xilinx_spi_regs *regs = priv->regs;
130
131 writel(SPISSR_ACT(cs), ®s->spissr);
132 }
133
spi_cs_deactivate(struct udevice * dev)134 static void spi_cs_deactivate(struct udevice *dev)
135 {
136 struct udevice *bus = dev_get_parent(dev);
137 struct xilinx_spi_priv *priv = dev_get_priv(bus);
138 struct xilinx_spi_regs *regs = priv->regs;
139
140 writel(SPISSR_OFF, ®s->spissr);
141 }
142
xilinx_spi_claim_bus(struct udevice * dev)143 static int xilinx_spi_claim_bus(struct udevice *dev)
144 {
145 struct udevice *bus = dev_get_parent(dev);
146 struct xilinx_spi_priv *priv = dev_get_priv(bus);
147 struct xilinx_spi_regs *regs = priv->regs;
148
149 writel(SPISSR_OFF, ®s->spissr);
150 writel(XILSPI_SPICR_DFLT_ON, ®s->spicr);
151
152 return 0;
153 }
154
xilinx_spi_release_bus(struct udevice * dev)155 static int xilinx_spi_release_bus(struct udevice *dev)
156 {
157 struct udevice *bus = dev_get_parent(dev);
158 struct xilinx_spi_priv *priv = dev_get_priv(bus);
159 struct xilinx_spi_regs *regs = priv->regs;
160
161 writel(SPISSR_OFF, ®s->spissr);
162 writel(XILSPI_SPICR_DFLT_OFF, ®s->spicr);
163
164 return 0;
165 }
166
xilinx_spi_fill_txfifo(struct udevice * bus,const u8 * txp,u32 txbytes)167 static u32 xilinx_spi_fill_txfifo(struct udevice *bus, const u8 *txp,
168 u32 txbytes)
169 {
170 struct xilinx_spi_priv *priv = dev_get_priv(bus);
171 struct xilinx_spi_regs *regs = priv->regs;
172 unsigned char d;
173 u32 i = 0;
174
175 while (txbytes && !(readl(®s->spisr) & SPISR_TX_FULL) &&
176 i < priv->fifo_depth) {
177 d = txp ? *txp++ : CONFIG_XILINX_SPI_IDLE_VAL;
178 debug("spi_xfer: tx:%x ", d);
179 /* write out and wait for processing (receive data) */
180 writel(d & SPIDTR_8BIT_MASK, ®s->spidtr);
181 txbytes--;
182 i++;
183 }
184
185 return i;
186 }
187
xilinx_spi_read_rxfifo(struct udevice * bus,u8 * rxp,u32 rxbytes)188 static u32 xilinx_spi_read_rxfifo(struct udevice *bus, u8 *rxp, u32 rxbytes)
189 {
190 struct xilinx_spi_priv *priv = dev_get_priv(bus);
191 struct xilinx_spi_regs *regs = priv->regs;
192 unsigned char d;
193 unsigned int i = 0;
194
195 while (rxbytes && !(readl(®s->spisr) & SPISR_RX_EMPTY)) {
196 d = readl(®s->spidrr) & SPIDRR_8BIT_MASK;
197 if (rxp)
198 *rxp++ = d;
199 debug("spi_xfer: rx:%x\n", d);
200 rxbytes--;
201 i++;
202 }
203 debug("Rx_done\n");
204
205 return i;
206 }
207
xilinx_spi_startup_block(struct udevice * dev,unsigned int bytes,const void * dout,void * din)208 static void xilinx_spi_startup_block(struct udevice *dev, unsigned int bytes,
209 const void *dout, void *din)
210 {
211 struct udevice *bus = dev_get_parent(dev);
212 struct xilinx_spi_priv *priv = dev_get_priv(bus);
213 struct xilinx_spi_regs *regs = priv->regs;
214 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
215 const unsigned char *txp = dout;
216 unsigned char *rxp = din;
217 u32 reg, count;
218 u32 txbytes = bytes;
219 u32 rxbytes = bytes;
220
221 /*
222 * This loop runs two times. First time to send the command.
223 * Second time to transfer data. After transferring data,
224 * it sets txp to the initial value for the normal operation.
225 */
226 for ( ; priv->startup < 2; priv->startup++) {
227 count = xilinx_spi_fill_txfifo(bus, txp, txbytes);
228 reg = readl(®s->spicr) & ~SPICR_MASTER_INHIBIT;
229 writel(reg, ®s->spicr);
230 count = xilinx_spi_read_rxfifo(bus, rxp, rxbytes);
231 txp = din;
232
233 if (priv->startup) {
234 spi_cs_deactivate(dev);
235 spi_cs_activate(dev, slave_plat->cs);
236 txp = dout;
237 }
238 }
239 }
240
xilinx_spi_xfer(struct udevice * dev,unsigned int bitlen,const void * dout,void * din,unsigned long flags)241 static int xilinx_spi_xfer(struct udevice *dev, unsigned int bitlen,
242 const void *dout, void *din, unsigned long flags)
243 {
244 struct udevice *bus = dev_get_parent(dev);
245 struct xilinx_spi_priv *priv = dev_get_priv(bus);
246 struct xilinx_spi_regs *regs = priv->regs;
247 struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev);
248 /* assume spi core configured to do 8 bit transfers */
249 unsigned int bytes = bitlen / XILSPI_MAX_XFER_BITS;
250 const unsigned char *txp = dout;
251 unsigned char *rxp = din;
252 u32 txbytes = bytes;
253 u32 rxbytes = bytes;
254 u32 reg, count, timeout;
255 int ret;
256
257 debug("spi_xfer: bus:%i cs:%i bitlen:%i bytes:%i flags:%lx\n",
258 bus->seq, slave_plat->cs, bitlen, bytes, flags);
259
260 if (bitlen == 0)
261 goto done;
262
263 if (bitlen % XILSPI_MAX_XFER_BITS) {
264 printf("XILSPI warning: Not a multiple of %d bits\n",
265 XILSPI_MAX_XFER_BITS);
266 flags |= SPI_XFER_END;
267 goto done;
268 }
269
270 if (flags & SPI_XFER_BEGIN)
271 spi_cs_activate(dev, slave_plat->cs);
272
273 /*
274 * This is the work around for the startup block issue in
275 * the spi controller. SPI clock is passing through STARTUP
276 * block to FLASH. STARTUP block don't provide clock as soon
277 * as QSPI provides command. So first command fails.
278 */
279 xilinx_spi_startup_block(dev, bytes, dout, din);
280
281 while (txbytes && rxbytes) {
282 count = xilinx_spi_fill_txfifo(bus, txp, txbytes);
283 reg = readl(®s->spicr) & ~SPICR_MASTER_INHIBIT;
284 writel(reg, ®s->spicr);
285 txbytes -= count;
286 if (txp)
287 txp += count;
288
289 ret = wait_for_bit_le32(®s->spisr, SPISR_TX_EMPTY, true,
290 XILINX_SPISR_TIMEOUT, false);
291 if (ret < 0) {
292 printf("XILSPI error: Xfer timeout\n");
293 return ret;
294 }
295
296 debug("txbytes:0x%x,txp:0x%p\n", txbytes, txp);
297 count = xilinx_spi_read_rxfifo(bus, rxp, rxbytes);
298 rxbytes -= count;
299 if (rxp)
300 rxp += count;
301 debug("rxbytes:0x%x rxp:0x%p\n", rxbytes, rxp);
302 }
303
304 done:
305 if (flags & SPI_XFER_END)
306 spi_cs_deactivate(dev);
307
308 return 0;
309 }
310
xilinx_spi_set_speed(struct udevice * bus,uint speed)311 static int xilinx_spi_set_speed(struct udevice *bus, uint speed)
312 {
313 struct xilinx_spi_priv *priv = dev_get_priv(bus);
314
315 priv->freq = speed;
316
317 debug("xilinx_spi_set_speed: regs=%p, speed=%d\n", priv->regs,
318 priv->freq);
319
320 return 0;
321 }
322
xilinx_spi_set_mode(struct udevice * bus,uint mode)323 static int xilinx_spi_set_mode(struct udevice *bus, uint mode)
324 {
325 struct xilinx_spi_priv *priv = dev_get_priv(bus);
326 struct xilinx_spi_regs *regs = priv->regs;
327 uint32_t spicr;
328
329 spicr = readl(®s->spicr);
330 if (mode & SPI_LSB_FIRST)
331 spicr |= SPICR_LSB_FIRST;
332 if (mode & SPI_CPHA)
333 spicr |= SPICR_CPHA;
334 if (mode & SPI_CPOL)
335 spicr |= SPICR_CPOL;
336 if (mode & SPI_LOOP)
337 spicr |= SPICR_LOOP;
338
339 writel(spicr, ®s->spicr);
340 priv->mode = mode;
341
342 debug("xilinx_spi_set_mode: regs=%p, mode=%d\n", priv->regs,
343 priv->mode);
344
345 return 0;
346 }
347
348 static const struct dm_spi_ops xilinx_spi_ops = {
349 .claim_bus = xilinx_spi_claim_bus,
350 .release_bus = xilinx_spi_release_bus,
351 .xfer = xilinx_spi_xfer,
352 .set_speed = xilinx_spi_set_speed,
353 .set_mode = xilinx_spi_set_mode,
354 };
355
356 static const struct udevice_id xilinx_spi_ids[] = {
357 { .compatible = "xlnx,xps-spi-2.00.a" },
358 { .compatible = "xlnx,xps-spi-2.00.b" },
359 { }
360 };
361
362 U_BOOT_DRIVER(xilinx_spi) = {
363 .name = "xilinx_spi",
364 .id = UCLASS_SPI,
365 .of_match = xilinx_spi_ids,
366 .ops = &xilinx_spi_ops,
367 .priv_auto_alloc_size = sizeof(struct xilinx_spi_priv),
368 .probe = xilinx_spi_probe,
369 };
370