xref: /openbmc/linux/arch/powerpc/include/asm/cpm2.h (revision fecc436a)
1 /* SPDX-License-Identifier: GPL-2.0 */
2 /*
3  * Communication Processor Module v2.
4  *
5  * This file contains structures and information for the communication
6  * processor channels found in the dual port RAM or parameter RAM.
7  * All CPM control and status is available through the CPM2 internal
8  * memory map.  See immap_cpm2.h for details.
9  */
10 #ifdef __KERNEL__
11 #ifndef __CPM2__
12 #define __CPM2__
13 
14 #include <asm/immap_cpm2.h>
15 #include <asm/cpm.h>
16 #include <sysdev/fsl_soc.h>
17 
18 /* CPM Command register.
19 */
20 #define CPM_CR_RST	((uint)0x80000000)
21 #define CPM_CR_PAGE	((uint)0x7c000000)
22 #define CPM_CR_SBLOCK	((uint)0x03e00000)
23 #define CPM_CR_FLG	((uint)0x00010000)
24 #define CPM_CR_MCN	((uint)0x00003fc0)
25 #define CPM_CR_OPCODE	((uint)0x0000000f)
26 
27 /* Device sub-block and page codes.
28 */
29 #define CPM_CR_SCC1_SBLOCK	(0x04)
30 #define CPM_CR_SCC2_SBLOCK	(0x05)
31 #define CPM_CR_SCC3_SBLOCK	(0x06)
32 #define CPM_CR_SCC4_SBLOCK	(0x07)
33 #define CPM_CR_SMC1_SBLOCK	(0x08)
34 #define CPM_CR_SMC2_SBLOCK	(0x09)
35 #define CPM_CR_SPI_SBLOCK	(0x0a)
36 #define CPM_CR_I2C_SBLOCK	(0x0b)
37 #define CPM_CR_TIMER_SBLOCK	(0x0f)
38 #define CPM_CR_RAND_SBLOCK	(0x0e)
39 #define CPM_CR_FCC1_SBLOCK	(0x10)
40 #define CPM_CR_FCC2_SBLOCK	(0x11)
41 #define CPM_CR_FCC3_SBLOCK	(0x12)
42 #define CPM_CR_IDMA1_SBLOCK	(0x14)
43 #define CPM_CR_IDMA2_SBLOCK	(0x15)
44 #define CPM_CR_IDMA3_SBLOCK	(0x16)
45 #define CPM_CR_IDMA4_SBLOCK	(0x17)
46 #define CPM_CR_MCC1_SBLOCK	(0x1c)
47 
48 #define CPM_CR_FCC_SBLOCK(x)	(x + 0x10)
49 
50 #define CPM_CR_SCC1_PAGE	(0x00)
51 #define CPM_CR_SCC2_PAGE	(0x01)
52 #define CPM_CR_SCC3_PAGE	(0x02)
53 #define CPM_CR_SCC4_PAGE	(0x03)
54 #define CPM_CR_SMC1_PAGE	(0x07)
55 #define CPM_CR_SMC2_PAGE	(0x08)
56 #define CPM_CR_SPI_PAGE		(0x09)
57 #define CPM_CR_I2C_PAGE		(0x0a)
58 #define CPM_CR_TIMER_PAGE	(0x0a)
59 #define CPM_CR_RAND_PAGE	(0x0a)
60 #define CPM_CR_FCC1_PAGE	(0x04)
61 #define CPM_CR_FCC2_PAGE	(0x05)
62 #define CPM_CR_FCC3_PAGE	(0x06)
63 #define CPM_CR_IDMA1_PAGE	(0x07)
64 #define CPM_CR_IDMA2_PAGE	(0x08)
65 #define CPM_CR_IDMA3_PAGE	(0x09)
66 #define CPM_CR_IDMA4_PAGE	(0x0a)
67 #define CPM_CR_MCC1_PAGE	(0x07)
68 #define CPM_CR_MCC2_PAGE	(0x08)
69 
70 #define CPM_CR_FCC_PAGE(x)	(x + 0x04)
71 
72 /* CPM2-specific opcodes (see cpm.h for common opcodes)
73 */
74 #define CPM_CR_START_IDMA	((ushort)0x0009)
75 
76 #define mk_cr_cmd(PG, SBC, MCN, OP) \
77 	((PG << 26) | (SBC << 21) | (MCN << 6) | OP)
78 
79 /* The number of pages of host memory we allocate for CPM.  This is
80  * done early in kernel initialization to get physically contiguous
81  * pages.
82  */
83 #define NUM_CPM_HOST_PAGES	2
84 
85 /* Export the base address of the communication processor registers
86  * and dual port ram.
87  */
88 extern cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor */
89 
90 #define cpm_dpalloc cpm_muram_alloc
91 #define cpm_dpfree cpm_muram_free
92 #define cpm_dpram_addr cpm_muram_addr
93 
94 extern void cpm2_reset(void);
95 
96 /* Baud rate generators.
97 */
98 #define CPM_BRG_RST		((uint)0x00020000)
99 #define CPM_BRG_EN		((uint)0x00010000)
100 #define CPM_BRG_EXTC_INT	((uint)0x00000000)
101 #define CPM_BRG_EXTC_CLK3_9	((uint)0x00004000)
102 #define CPM_BRG_EXTC_CLK5_15	((uint)0x00008000)
103 #define CPM_BRG_ATB		((uint)0x00002000)
104 #define CPM_BRG_CD_MASK		((uint)0x00001ffe)
105 #define CPM_BRG_DIV16		((uint)0x00000001)
106 
107 #define CPM2_BRG_INT_CLK	(get_brgfreq())
108 #define CPM2_BRG_UART_CLK	(CPM2_BRG_INT_CLK/16)
109 
110 extern void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src);
111 
112 /* This function is used by UARTS, or anything else that uses a 16x
113  * oversampled clock.
114  */
cpm_setbrg(uint brg,uint rate)115 static inline void cpm_setbrg(uint brg, uint rate)
116 {
117 	__cpm2_setbrg(brg, rate, CPM2_BRG_UART_CLK, 0, CPM_BRG_EXTC_INT);
118 }
119 
120 /* This function is used to set high speed synchronous baud rate
121  * clocks.
122  */
cpm2_fastbrg(uint brg,uint rate,int div16)123 static inline void cpm2_fastbrg(uint brg, uint rate, int div16)
124 {
125 	__cpm2_setbrg(brg, rate, CPM2_BRG_INT_CLK, div16, CPM_BRG_EXTC_INT);
126 }
127 
128 /* Parameter RAM offsets from the base.
129 */
130 #define PROFF_SCC1		((uint)0x8000)
131 #define PROFF_SCC2		((uint)0x8100)
132 #define PROFF_SCC3		((uint)0x8200)
133 #define PROFF_SCC4		((uint)0x8300)
134 #define PROFF_FCC1		((uint)0x8400)
135 #define PROFF_FCC2		((uint)0x8500)
136 #define PROFF_FCC3		((uint)0x8600)
137 #define PROFF_MCC1		((uint)0x8700)
138 #define PROFF_SMC1_BASE		((uint)0x87fc)
139 #define PROFF_IDMA1_BASE	((uint)0x87fe)
140 #define PROFF_MCC2		((uint)0x8800)
141 #define PROFF_SMC2_BASE		((uint)0x88fc)
142 #define PROFF_IDMA2_BASE	((uint)0x88fe)
143 #define PROFF_SPI_BASE		((uint)0x89fc)
144 #define PROFF_IDMA3_BASE	((uint)0x89fe)
145 #define PROFF_TIMERS		((uint)0x8ae0)
146 #define PROFF_REVNUM		((uint)0x8af0)
147 #define PROFF_RAND		((uint)0x8af8)
148 #define PROFF_I2C_BASE		((uint)0x8afc)
149 #define PROFF_IDMA4_BASE	((uint)0x8afe)
150 
151 #define PROFF_SCC_SIZE		((uint)0x100)
152 #define PROFF_FCC_SIZE		((uint)0x100)
153 #define PROFF_SMC_SIZE		((uint)64)
154 
155 /* The SMCs are relocated to any of the first eight DPRAM pages.
156  * We will fix these at the first locations of DPRAM, until we
157  * get some microcode patches :-).
158  * The parameter ram space for the SMCs is fifty-some bytes, and
159  * they are required to start on a 64 byte boundary.
160  */
161 #define PROFF_SMC1	(0)
162 #define PROFF_SMC2	(64)
163 
164 
165 /* Define enough so I can at least use the serial port as a UART.
166  */
167 typedef struct smc_uart {
168 	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
169 	ushort	smc_tbase;	/* Tx Buffer descriptor base address */
170 	u_char	smc_rfcr;	/* Rx function code */
171 	u_char	smc_tfcr;	/* Tx function code */
172 	ushort	smc_mrblr;	/* Max receive buffer length */
173 	uint	smc_rstate;	/* Internal */
174 	uint	smc_idp;	/* Internal */
175 	ushort	smc_rbptr;	/* Internal */
176 	ushort	smc_ibc;	/* Internal */
177 	uint	smc_rxtmp;	/* Internal */
178 	uint	smc_tstate;	/* Internal */
179 	uint	smc_tdp;	/* Internal */
180 	ushort	smc_tbptr;	/* Internal */
181 	ushort	smc_tbc;	/* Internal */
182 	uint	smc_txtmp;	/* Internal */
183 	ushort	smc_maxidl;	/* Maximum idle characters */
184 	ushort	smc_tmpidl;	/* Temporary idle counter */
185 	ushort	smc_brklen;	/* Last received break length */
186 	ushort	smc_brkec;	/* rcv'd break condition counter */
187 	ushort	smc_brkcr;	/* xmt break count register */
188 	ushort	smc_rmask;	/* Temporary bit mask */
189 	uint	smc_stmp;	/* SDMA Temp */
190 } smc_uart_t;
191 
192 /* SMC uart mode register (Internal memory map).
193 */
194 #define SMCMR_REN	((ushort)0x0001)
195 #define SMCMR_TEN	((ushort)0x0002)
196 #define SMCMR_DM	((ushort)0x000c)
197 #define SMCMR_SM_GCI	((ushort)0x0000)
198 #define SMCMR_SM_UART	((ushort)0x0020)
199 #define SMCMR_SM_TRANS	((ushort)0x0030)
200 #define SMCMR_SM_MASK	((ushort)0x0030)
201 #define SMCMR_PM_EVEN	((ushort)0x0100)	/* Even parity, else odd */
202 #define SMCMR_REVD	SMCMR_PM_EVEN
203 #define SMCMR_PEN	((ushort)0x0200)	/* Parity enable */
204 #define SMCMR_BS	SMCMR_PEN
205 #define SMCMR_SL	((ushort)0x0400)	/* Two stops, else one */
206 #define SMCR_CLEN_MASK	((ushort)0x7800)	/* Character length */
207 #define smcr_mk_clen(C)	(((C) << 11) & SMCR_CLEN_MASK)
208 
209 /* SMC Event and Mask register.
210 */
211 #define SMCM_BRKE       ((unsigned char)0x40)   /* When in UART Mode */
212 #define SMCM_BRK        ((unsigned char)0x10)   /* When in UART Mode */
213 #define SMCM_TXE	((unsigned char)0x10)
214 #define SMCM_BSY	((unsigned char)0x04)
215 #define SMCM_TX		((unsigned char)0x02)
216 #define SMCM_RX		((unsigned char)0x01)
217 
218 /* SCCs.
219 */
220 #define SCC_GSMRH_IRP		((uint)0x00040000)
221 #define SCC_GSMRH_GDE		((uint)0x00010000)
222 #define SCC_GSMRH_TCRC_CCITT	((uint)0x00008000)
223 #define SCC_GSMRH_TCRC_BISYNC	((uint)0x00004000)
224 #define SCC_GSMRH_TCRC_HDLC	((uint)0x00000000)
225 #define SCC_GSMRH_REVD		((uint)0x00002000)
226 #define SCC_GSMRH_TRX		((uint)0x00001000)
227 #define SCC_GSMRH_TTX		((uint)0x00000800)
228 #define SCC_GSMRH_CDP		((uint)0x00000400)
229 #define SCC_GSMRH_CTSP		((uint)0x00000200)
230 #define SCC_GSMRH_CDS		((uint)0x00000100)
231 #define SCC_GSMRH_CTSS		((uint)0x00000080)
232 #define SCC_GSMRH_TFL		((uint)0x00000040)
233 #define SCC_GSMRH_RFW		((uint)0x00000020)
234 #define SCC_GSMRH_TXSY		((uint)0x00000010)
235 #define SCC_GSMRH_SYNL16	((uint)0x0000000c)
236 #define SCC_GSMRH_SYNL8		((uint)0x00000008)
237 #define SCC_GSMRH_SYNL4		((uint)0x00000004)
238 #define SCC_GSMRH_RTSM		((uint)0x00000002)
239 #define SCC_GSMRH_RSYN		((uint)0x00000001)
240 
241 #define SCC_GSMRL_SIR		((uint)0x80000000)	/* SCC2 only */
242 #define SCC_GSMRL_EDGE_NONE	((uint)0x60000000)
243 #define SCC_GSMRL_EDGE_NEG	((uint)0x40000000)
244 #define SCC_GSMRL_EDGE_POS	((uint)0x20000000)
245 #define SCC_GSMRL_EDGE_BOTH	((uint)0x00000000)
246 #define SCC_GSMRL_TCI		((uint)0x10000000)
247 #define SCC_GSMRL_TSNC_3	((uint)0x0c000000)
248 #define SCC_GSMRL_TSNC_4	((uint)0x08000000)
249 #define SCC_GSMRL_TSNC_14	((uint)0x04000000)
250 #define SCC_GSMRL_TSNC_INF	((uint)0x00000000)
251 #define SCC_GSMRL_RINV		((uint)0x02000000)
252 #define SCC_GSMRL_TINV		((uint)0x01000000)
253 #define SCC_GSMRL_TPL_128	((uint)0x00c00000)
254 #define SCC_GSMRL_TPL_64	((uint)0x00a00000)
255 #define SCC_GSMRL_TPL_48	((uint)0x00800000)
256 #define SCC_GSMRL_TPL_32	((uint)0x00600000)
257 #define SCC_GSMRL_TPL_16	((uint)0x00400000)
258 #define SCC_GSMRL_TPL_8		((uint)0x00200000)
259 #define SCC_GSMRL_TPL_NONE	((uint)0x00000000)
260 #define SCC_GSMRL_TPP_ALL1	((uint)0x00180000)
261 #define SCC_GSMRL_TPP_01	((uint)0x00100000)
262 #define SCC_GSMRL_TPP_10	((uint)0x00080000)
263 #define SCC_GSMRL_TPP_ZEROS	((uint)0x00000000)
264 #define SCC_GSMRL_TEND		((uint)0x00040000)
265 #define SCC_GSMRL_TDCR_32	((uint)0x00030000)
266 #define SCC_GSMRL_TDCR_16	((uint)0x00020000)
267 #define SCC_GSMRL_TDCR_8	((uint)0x00010000)
268 #define SCC_GSMRL_TDCR_1	((uint)0x00000000)
269 #define SCC_GSMRL_RDCR_32	((uint)0x0000c000)
270 #define SCC_GSMRL_RDCR_16	((uint)0x00008000)
271 #define SCC_GSMRL_RDCR_8	((uint)0x00004000)
272 #define SCC_GSMRL_RDCR_1	((uint)0x00000000)
273 #define SCC_GSMRL_RENC_DFMAN	((uint)0x00003000)
274 #define SCC_GSMRL_RENC_MANCH	((uint)0x00002000)
275 #define SCC_GSMRL_RENC_FM0	((uint)0x00001000)
276 #define SCC_GSMRL_RENC_NRZI	((uint)0x00000800)
277 #define SCC_GSMRL_RENC_NRZ	((uint)0x00000000)
278 #define SCC_GSMRL_TENC_DFMAN	((uint)0x00000600)
279 #define SCC_GSMRL_TENC_MANCH	((uint)0x00000400)
280 #define SCC_GSMRL_TENC_FM0	((uint)0x00000200)
281 #define SCC_GSMRL_TENC_NRZI	((uint)0x00000100)
282 #define SCC_GSMRL_TENC_NRZ	((uint)0x00000000)
283 #define SCC_GSMRL_DIAG_LE	((uint)0x000000c0)	/* Loop and echo */
284 #define SCC_GSMRL_DIAG_ECHO	((uint)0x00000080)
285 #define SCC_GSMRL_DIAG_LOOP	((uint)0x00000040)
286 #define SCC_GSMRL_DIAG_NORM	((uint)0x00000000)
287 #define SCC_GSMRL_ENR		((uint)0x00000020)
288 #define SCC_GSMRL_ENT		((uint)0x00000010)
289 #define SCC_GSMRL_MODE_ENET	((uint)0x0000000c)
290 #define SCC_GSMRL_MODE_DDCMP	((uint)0x00000009)
291 #define SCC_GSMRL_MODE_BISYNC	((uint)0x00000008)
292 #define SCC_GSMRL_MODE_V14	((uint)0x00000007)
293 #define SCC_GSMRL_MODE_AHDLC	((uint)0x00000006)
294 #define SCC_GSMRL_MODE_PROFIBUS	((uint)0x00000005)
295 #define SCC_GSMRL_MODE_UART	((uint)0x00000004)
296 #define SCC_GSMRL_MODE_SS7	((uint)0x00000003)
297 #define SCC_GSMRL_MODE_ATALK	((uint)0x00000002)
298 #define SCC_GSMRL_MODE_HDLC	((uint)0x00000000)
299 
300 #define SCC_TODR_TOD		((ushort)0x8000)
301 
302 /* SCC Event and Mask register.
303 */
304 #define SCCM_TXE	((unsigned char)0x10)
305 #define SCCM_BSY	((unsigned char)0x04)
306 #define SCCM_TX		((unsigned char)0x02)
307 #define SCCM_RX		((unsigned char)0x01)
308 
309 typedef struct scc_param {
310 	ushort	scc_rbase;	/* Rx Buffer descriptor base address */
311 	ushort	scc_tbase;	/* Tx Buffer descriptor base address */
312 	u_char	scc_rfcr;	/* Rx function code */
313 	u_char	scc_tfcr;	/* Tx function code */
314 	ushort	scc_mrblr;	/* Max receive buffer length */
315 	uint	scc_rstate;	/* Internal */
316 	uint	scc_idp;	/* Internal */
317 	ushort	scc_rbptr;	/* Internal */
318 	ushort	scc_ibc;	/* Internal */
319 	uint	scc_rxtmp;	/* Internal */
320 	uint	scc_tstate;	/* Internal */
321 	uint	scc_tdp;	/* Internal */
322 	ushort	scc_tbptr;	/* Internal */
323 	ushort	scc_tbc;	/* Internal */
324 	uint	scc_txtmp;	/* Internal */
325 	uint	scc_rcrc;	/* Internal */
326 	uint	scc_tcrc;	/* Internal */
327 } sccp_t;
328 
329 /* Function code bits.
330 */
331 #define SCC_EB	((u_char) 0x10)	/* Set big endian byte order */
332 #define SCC_GBL	((u_char) 0x20) /* Snooping enabled */
333 
334 /* CPM Ethernet through SCC1.
335  */
336 typedef struct scc_enet {
337 	sccp_t	sen_genscc;
338 	uint	sen_cpres;	/* Preset CRC */
339 	uint	sen_cmask;	/* Constant mask for CRC */
340 	uint	sen_crcec;	/* CRC Error counter */
341 	uint	sen_alec;	/* alignment error counter */
342 	uint	sen_disfc;	/* discard frame counter */
343 	ushort	sen_pads;	/* Tx short frame pad character */
344 	ushort	sen_retlim;	/* Retry limit threshold */
345 	ushort	sen_retcnt;	/* Retry limit counter */
346 	ushort	sen_maxflr;	/* maximum frame length register */
347 	ushort	sen_minflr;	/* minimum frame length register */
348 	ushort	sen_maxd1;	/* maximum DMA1 length */
349 	ushort	sen_maxd2;	/* maximum DMA2 length */
350 	ushort	sen_maxd;	/* Rx max DMA */
351 	ushort	sen_dmacnt;	/* Rx DMA counter */
352 	ushort	sen_maxb;	/* Max BD byte count */
353 	ushort	sen_gaddr1;	/* Group address filter */
354 	ushort	sen_gaddr2;
355 	ushort	sen_gaddr3;
356 	ushort	sen_gaddr4;
357 	uint	sen_tbuf0data0;	/* Save area 0 - current frame */
358 	uint	sen_tbuf0data1;	/* Save area 1 - current frame */
359 	uint	sen_tbuf0rba;	/* Internal */
360 	uint	sen_tbuf0crc;	/* Internal */
361 	ushort	sen_tbuf0bcnt;	/* Internal */
362 	ushort	sen_paddrh;	/* physical address (MSB) */
363 	ushort	sen_paddrm;
364 	ushort	sen_paddrl;	/* physical address (LSB) */
365 	ushort	sen_pper;	/* persistence */
366 	ushort	sen_rfbdptr;	/* Rx first BD pointer */
367 	ushort	sen_tfbdptr;	/* Tx first BD pointer */
368 	ushort	sen_tlbdptr;	/* Tx last BD pointer */
369 	uint	sen_tbuf1data0;	/* Save area 0 - current frame */
370 	uint	sen_tbuf1data1;	/* Save area 1 - current frame */
371 	uint	sen_tbuf1rba;	/* Internal */
372 	uint	sen_tbuf1crc;	/* Internal */
373 	ushort	sen_tbuf1bcnt;	/* Internal */
374 	ushort	sen_txlen;	/* Tx Frame length counter */
375 	ushort	sen_iaddr1;	/* Individual address filter */
376 	ushort	sen_iaddr2;
377 	ushort	sen_iaddr3;
378 	ushort	sen_iaddr4;
379 	ushort	sen_boffcnt;	/* Backoff counter */
380 
381 	/* NOTE: Some versions of the manual have the following items
382 	 * incorrectly documented.  Below is the proper order.
383 	 */
384 	ushort	sen_taddrh;	/* temp address (MSB) */
385 	ushort	sen_taddrm;
386 	ushort	sen_taddrl;	/* temp address (LSB) */
387 } scc_enet_t;
388 
389 
390 /* SCC Event register as used by Ethernet.
391 */
392 #define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
393 #define SCCE_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
394 #define SCCE_ENET_RXF	((ushort)0x0008)	/* Full frame received */
395 #define SCCE_ENET_BSY	((ushort)0x0004)	/* All incoming buffers full */
396 #define SCCE_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
397 #define SCCE_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
398 
399 /* SCC Mode Register (PSMR) as used by Ethernet.
400 */
401 #define SCC_PSMR_HBC	((ushort)0x8000)	/* Enable heartbeat */
402 #define SCC_PSMR_FC	((ushort)0x4000)	/* Force collision */
403 #define SCC_PSMR_RSH	((ushort)0x2000)	/* Receive short frames */
404 #define SCC_PSMR_IAM	((ushort)0x1000)	/* Check individual hash */
405 #define SCC_PSMR_ENCRC	((ushort)0x0800)	/* Ethernet CRC mode */
406 #define SCC_PSMR_PRO	((ushort)0x0200)	/* Promiscuous mode */
407 #define SCC_PSMR_BRO	((ushort)0x0100)	/* Catch broadcast pkts */
408 #define SCC_PSMR_SBT	((ushort)0x0080)	/* Special backoff timer */
409 #define SCC_PSMR_LPB	((ushort)0x0040)	/* Set Loopback mode */
410 #define SCC_PSMR_SIP	((ushort)0x0020)	/* Sample Input Pins */
411 #define SCC_PSMR_LCW	((ushort)0x0010)	/* Late collision window */
412 #define SCC_PSMR_NIB22	((ushort)0x000a)	/* Start frame search */
413 #define SCC_PSMR_FDE	((ushort)0x0001)	/* Full duplex enable */
414 
415 /* SCC as UART
416 */
417 typedef struct scc_uart {
418 	sccp_t	scc_genscc;
419 	uint	scc_res1;	/* Reserved */
420 	uint	scc_res2;	/* Reserved */
421 	ushort	scc_maxidl;	/* Maximum idle chars */
422 	ushort	scc_idlc;	/* temp idle counter */
423 	ushort	scc_brkcr;	/* Break count register */
424 	ushort	scc_parec;	/* receive parity error counter */
425 	ushort	scc_frmec;	/* receive framing error counter */
426 	ushort	scc_nosec;	/* receive noise counter */
427 	ushort	scc_brkec;	/* receive break condition counter */
428 	ushort	scc_brkln;	/* last received break length */
429 	ushort	scc_uaddr1;	/* UART address character 1 */
430 	ushort	scc_uaddr2;	/* UART address character 2 */
431 	ushort	scc_rtemp;	/* Temp storage */
432 	ushort	scc_toseq;	/* Transmit out of sequence char */
433 	ushort	scc_char1;	/* control character 1 */
434 	ushort	scc_char2;	/* control character 2 */
435 	ushort	scc_char3;	/* control character 3 */
436 	ushort	scc_char4;	/* control character 4 */
437 	ushort	scc_char5;	/* control character 5 */
438 	ushort	scc_char6;	/* control character 6 */
439 	ushort	scc_char7;	/* control character 7 */
440 	ushort	scc_char8;	/* control character 8 */
441 	ushort	scc_rccm;	/* receive control character mask */
442 	ushort	scc_rccr;	/* receive control character register */
443 	ushort	scc_rlbc;	/* receive last break character */
444 } scc_uart_t;
445 
446 /* SCC Event and Mask registers when it is used as a UART.
447 */
448 #define UART_SCCM_GLR		((ushort)0x1000)
449 #define UART_SCCM_GLT		((ushort)0x0800)
450 #define UART_SCCM_AB		((ushort)0x0200)
451 #define UART_SCCM_IDL		((ushort)0x0100)
452 #define UART_SCCM_GRA		((ushort)0x0080)
453 #define UART_SCCM_BRKE		((ushort)0x0040)
454 #define UART_SCCM_BRKS		((ushort)0x0020)
455 #define UART_SCCM_CCR		((ushort)0x0008)
456 #define UART_SCCM_BSY		((ushort)0x0004)
457 #define UART_SCCM_TX		((ushort)0x0002)
458 #define UART_SCCM_RX		((ushort)0x0001)
459 
460 /* The SCC PSMR when used as a UART.
461 */
462 #define SCU_PSMR_FLC		((ushort)0x8000)
463 #define SCU_PSMR_SL		((ushort)0x4000)
464 #define SCU_PSMR_CL		((ushort)0x3000)
465 #define SCU_PSMR_UM		((ushort)0x0c00)
466 #define SCU_PSMR_FRZ		((ushort)0x0200)
467 #define SCU_PSMR_RZS		((ushort)0x0100)
468 #define SCU_PSMR_SYN		((ushort)0x0080)
469 #define SCU_PSMR_DRT		((ushort)0x0040)
470 #define SCU_PSMR_PEN		((ushort)0x0010)
471 #define SCU_PSMR_RPM		((ushort)0x000c)
472 #define SCU_PSMR_REVP		((ushort)0x0008)
473 #define SCU_PSMR_TPM		((ushort)0x0003)
474 #define SCU_PSMR_TEVP		((ushort)0x0002)
475 
476 /* CPM Transparent mode SCC.
477  */
478 typedef struct scc_trans {
479 	sccp_t	st_genscc;
480 	uint	st_cpres;	/* Preset CRC */
481 	uint	st_cmask;	/* Constant mask for CRC */
482 } scc_trans_t;
483 
484 /* How about some FCCs.....
485 */
486 #define FCC_GFMR_DIAG_NORM	((uint)0x00000000)
487 #define FCC_GFMR_DIAG_LE	((uint)0x40000000)
488 #define FCC_GFMR_DIAG_AE	((uint)0x80000000)
489 #define FCC_GFMR_DIAG_ALE	((uint)0xc0000000)
490 #define FCC_GFMR_TCI		((uint)0x20000000)
491 #define FCC_GFMR_TRX		((uint)0x10000000)
492 #define FCC_GFMR_TTX		((uint)0x08000000)
493 #define FCC_GFMR_CDP		((uint)0x04000000)
494 #define FCC_GFMR_CTSP		((uint)0x02000000)
495 #define FCC_GFMR_CDS		((uint)0x01000000)
496 #define FCC_GFMR_CTSS		((uint)0x00800000)
497 #define FCC_GFMR_SYNL_NONE	((uint)0x00000000)
498 #define FCC_GFMR_SYNL_AUTO	((uint)0x00004000)
499 #define FCC_GFMR_SYNL_8		((uint)0x00008000)
500 #define FCC_GFMR_SYNL_16	((uint)0x0000c000)
501 #define FCC_GFMR_RTSM		((uint)0x00002000)
502 #define FCC_GFMR_RENC_NRZ	((uint)0x00000000)
503 #define FCC_GFMR_RENC_NRZI	((uint)0x00000800)
504 #define FCC_GFMR_REVD		((uint)0x00000400)
505 #define FCC_GFMR_TENC_NRZ	((uint)0x00000000)
506 #define FCC_GFMR_TENC_NRZI	((uint)0x00000100)
507 #define FCC_GFMR_TCRC_16	((uint)0x00000000)
508 #define FCC_GFMR_TCRC_32	((uint)0x00000080)
509 #define FCC_GFMR_ENR		((uint)0x00000020)
510 #define FCC_GFMR_ENT		((uint)0x00000010)
511 #define FCC_GFMR_MODE_ENET	((uint)0x0000000c)
512 #define FCC_GFMR_MODE_ATM	((uint)0x0000000a)
513 #define FCC_GFMR_MODE_HDLC	((uint)0x00000000)
514 
515 /* Generic FCC parameter ram.
516 */
517 typedef struct fcc_param {
518 	ushort	fcc_riptr;	/* Rx Internal temp pointer */
519 	ushort	fcc_tiptr;	/* Tx Internal temp pointer */
520 	ushort	fcc_res1;
521 	ushort	fcc_mrblr;	/* Max receive buffer length, mod 32 bytes */
522 	uint	fcc_rstate;	/* Upper byte is Func code, must be set */
523 	uint	fcc_rbase;	/* Receive BD base */
524 	ushort	fcc_rbdstat;	/* RxBD status */
525 	ushort	fcc_rbdlen;	/* RxBD down counter */
526 	uint	fcc_rdptr;	/* RxBD internal data pointer */
527 	uint	fcc_tstate;	/* Upper byte is Func code, must be set */
528 	uint	fcc_tbase;	/* Transmit BD base */
529 	ushort	fcc_tbdstat;	/* TxBD status */
530 	ushort	fcc_tbdlen;	/* TxBD down counter */
531 	uint	fcc_tdptr;	/* TxBD internal data pointer */
532 	uint	fcc_rbptr;	/* Rx BD Internal buf pointer */
533 	uint	fcc_tbptr;	/* Tx BD Internal buf pointer */
534 	uint	fcc_rcrc;	/* Rx temp CRC */
535 	uint	fcc_res2;
536 	uint	fcc_tcrc;	/* Tx temp CRC */
537 } fccp_t;
538 
539 
540 /* Ethernet controller through FCC.
541 */
542 typedef struct fcc_enet {
543 	fccp_t	fen_genfcc;
544 	uint	fen_statbuf;	/* Internal status buffer */
545 	uint	fen_camptr;	/* CAM address */
546 	uint	fen_cmask;	/* Constant mask for CRC */
547 	uint	fen_cpres;	/* Preset CRC */
548 	uint	fen_crcec;	/* CRC Error counter */
549 	uint	fen_alec;	/* alignment error counter */
550 	uint	fen_disfc;	/* discard frame counter */
551 	ushort	fen_retlim;	/* Retry limit */
552 	ushort	fen_retcnt;	/* Retry counter */
553 	ushort	fen_pper;	/* Persistence */
554 	ushort	fen_boffcnt;	/* backoff counter */
555 	uint	fen_gaddrh;	/* Group address filter, high 32-bits */
556 	uint	fen_gaddrl;	/* Group address filter, low 32-bits */
557 	ushort	fen_tfcstat;	/* out of sequence TxBD */
558 	ushort	fen_tfclen;
559 	uint	fen_tfcptr;
560 	ushort	fen_mflr;	/* Maximum frame length (1518) */
561 	ushort	fen_paddrh;	/* MAC address */
562 	ushort	fen_paddrm;
563 	ushort	fen_paddrl;
564 	ushort	fen_ibdcount;	/* Internal BD counter */
565 	ushort	fen_ibdstart;	/* Internal BD start pointer */
566 	ushort	fen_ibdend;	/* Internal BD end pointer */
567 	ushort	fen_txlen;	/* Internal Tx frame length counter */
568 	uint	fen_ibdbase[8]; /* Internal use */
569 	uint	fen_iaddrh;	/* Individual address filter */
570 	uint	fen_iaddrl;
571 	ushort	fen_minflr;	/* Minimum frame length (64) */
572 	ushort	fen_taddrh;	/* Filter transfer MAC address */
573 	ushort	fen_taddrm;
574 	ushort	fen_taddrl;
575 	ushort	fen_padptr;	/* Pointer to pad byte buffer */
576 	ushort	fen_cftype;	/* control frame type */
577 	ushort	fen_cfrange;	/* control frame range */
578 	ushort	fen_maxb;	/* maximum BD count */
579 	ushort	fen_maxd1;	/* Max DMA1 length (1520) */
580 	ushort	fen_maxd2;	/* Max DMA2 length (1520) */
581 	ushort	fen_maxd;	/* internal max DMA count */
582 	ushort	fen_dmacnt;	/* internal DMA counter */
583 	uint	fen_octc;	/* Total octect counter */
584 	uint	fen_colc;	/* Total collision counter */
585 	uint	fen_broc;	/* Total broadcast packet counter */
586 	uint	fen_mulc;	/* Total multicast packet count */
587 	uint	fen_uspc;	/* Total packets < 64 bytes */
588 	uint	fen_frgc;	/* Total packets < 64 bytes with errors */
589 	uint	fen_ospc;	/* Total packets > 1518 */
590 	uint	fen_jbrc;	/* Total packets > 1518 with errors */
591 	uint	fen_p64c;	/* Total packets == 64 bytes */
592 	uint	fen_p65c;	/* Total packets 64 < bytes <= 127 */
593 	uint	fen_p128c;	/* Total packets 127 < bytes <= 255 */
594 	uint	fen_p256c;	/* Total packets 256 < bytes <= 511 */
595 	uint	fen_p512c;	/* Total packets 512 < bytes <= 1023 */
596 	uint	fen_p1024c;	/* Total packets 1024 < bytes <= 1518 */
597 	uint	fen_cambuf;	/* Internal CAM buffer pointer */
598 	ushort	fen_rfthr;	/* Received frames threshold */
599 	ushort	fen_rfcnt;	/* Received frames count */
600 } fcc_enet_t;
601 
602 /* FCC Event/Mask register as used by Ethernet.
603 */
604 #define FCC_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
605 #define FCC_ENET_RXC	((ushort)0x0040)	/* Control Frame Received */
606 #define FCC_ENET_TXC	((ushort)0x0020)	/* Out of seq. Tx sent */
607 #define FCC_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
608 #define FCC_ENET_RXF	((ushort)0x0008)	/* Full frame received */
609 #define FCC_ENET_BSY	((ushort)0x0004)	/* Busy.  Rx Frame dropped */
610 #define FCC_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
611 #define FCC_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
612 
613 /* FCC Mode Register (FPSMR) as used by Ethernet.
614 */
615 #define FCC_PSMR_HBC	((uint)0x80000000)	/* Enable heartbeat */
616 #define FCC_PSMR_FC	((uint)0x40000000)	/* Force Collision */
617 #define FCC_PSMR_SBT	((uint)0x20000000)	/* Stop backoff timer */
618 #define FCC_PSMR_LPB	((uint)0x10000000)	/* Local protect. 1 = FDX */
619 #define FCC_PSMR_LCW	((uint)0x08000000)	/* Late collision select */
620 #define FCC_PSMR_FDE	((uint)0x04000000)	/* Full Duplex Enable */
621 #define FCC_PSMR_MON	((uint)0x02000000)	/* RMON Enable */
622 #define FCC_PSMR_PRO	((uint)0x00400000)	/* Promiscuous Enable */
623 #define FCC_PSMR_FCE	((uint)0x00200000)	/* Flow Control Enable */
624 #define FCC_PSMR_RSH	((uint)0x00100000)	/* Receive Short Frames */
625 #define FCC_PSMR_CAM	((uint)0x00000400)	/* CAM enable */
626 #define FCC_PSMR_BRO	((uint)0x00000200)	/* Broadcast pkt discard */
627 #define FCC_PSMR_ENCRC	((uint)0x00000080)	/* Use 32-bit CRC */
628 
629 /* IIC parameter RAM.
630 */
631 typedef struct iic {
632 	ushort	iic_rbase;	/* Rx Buffer descriptor base address */
633 	ushort	iic_tbase;	/* Tx Buffer descriptor base address */
634 	u_char	iic_rfcr;	/* Rx function code */
635 	u_char	iic_tfcr;	/* Tx function code */
636 	ushort	iic_mrblr;	/* Max receive buffer length */
637 	uint	iic_rstate;	/* Internal */
638 	uint	iic_rdp;	/* Internal */
639 	ushort	iic_rbptr;	/* Internal */
640 	ushort	iic_rbc;	/* Internal */
641 	uint	iic_rxtmp;	/* Internal */
642 	uint	iic_tstate;	/* Internal */
643 	uint	iic_tdp;	/* Internal */
644 	ushort	iic_tbptr;	/* Internal */
645 	ushort	iic_tbc;	/* Internal */
646 	uint	iic_txtmp;	/* Internal */
647 } iic_t;
648 
649 /* IDMA parameter RAM
650 */
651 typedef struct idma {
652 	ushort ibase;		/* IDMA buffer descriptor table base address */
653 	ushort dcm;		/* DMA channel mode */
654 	ushort ibdptr;		/* IDMA current buffer descriptor pointer */
655 	ushort dpr_buf;		/* IDMA transfer buffer base address */
656 	ushort buf_inv;		/* internal buffer inventory */
657 	ushort ss_max;		/* steady-state maximum transfer size */
658 	ushort dpr_in_ptr;	/* write pointer inside the internal buffer */
659 	ushort sts;		/* source transfer size */
660 	ushort dpr_out_ptr;	/* read pointer inside the internal buffer */
661 	ushort seob;		/* source end of burst */
662 	ushort deob;		/* destination end of burst */
663 	ushort dts;		/* destination transfer size */
664 	ushort ret_add;		/* return address when working in ERM=1 mode */
665 	ushort res0;		/* reserved */
666 	uint   bd_cnt;		/* internal byte count */
667 	uint   s_ptr;		/* source internal data pointer */
668 	uint   d_ptr;		/* destination internal data pointer */
669 	uint   istate;		/* internal state */
670 	u_char res1[20];	/* pad to 64-byte length */
671 } idma_t;
672 
673 /* DMA channel mode bit fields
674 */
675 #define IDMA_DCM_FB		((ushort)0x8000) /* fly-by mode */
676 #define IDMA_DCM_LP		((ushort)0x4000) /* low priority */
677 #define IDMA_DCM_TC2		((ushort)0x0400) /* value driven on TC[2] */
678 #define IDMA_DCM_DMA_WRAP_MASK	((ushort)0x01c0) /* mask for DMA wrap */
679 #define IDMA_DCM_DMA_WRAP_64	((ushort)0x0000) /* 64-byte DMA xfer buffer */
680 #define IDMA_DCM_DMA_WRAP_128	((ushort)0x0040) /* 128-byte DMA xfer buffer */
681 #define IDMA_DCM_DMA_WRAP_256	((ushort)0x0080) /* 256-byte DMA xfer buffer */
682 #define IDMA_DCM_DMA_WRAP_512	((ushort)0x00c0) /* 512-byte DMA xfer buffer */
683 #define IDMA_DCM_DMA_WRAP_1024	((ushort)0x0100) /* 1024-byte DMA xfer buffer */
684 #define IDMA_DCM_DMA_WRAP_2048	((ushort)0x0140) /* 2048-byte DMA xfer buffer */
685 #define IDMA_DCM_SINC		((ushort)0x0020) /* source inc addr */
686 #define IDMA_DCM_DINC		((ushort)0x0010) /* destination inc addr */
687 #define IDMA_DCM_ERM		((ushort)0x0008) /* external request mode */
688 #define IDMA_DCM_DT		((ushort)0x0004) /* DONE treatment */
689 #define IDMA_DCM_SD_MASK	((ushort)0x0003) /* mask for SD bit field */
690 #define IDMA_DCM_SD_MEM2MEM	((ushort)0x0000) /* memory-to-memory xfer */
691 #define IDMA_DCM_SD_PER2MEM	((ushort)0x0002) /* peripheral-to-memory xfer */
692 #define IDMA_DCM_SD_MEM2PER	((ushort)0x0001) /* memory-to-peripheral xfer */
693 
694 /* IDMA Buffer Descriptors
695 */
696 typedef struct idma_bd {
697 	uint flags;
698 	uint len;	/* data length */
699 	uint src;	/* source data buffer pointer */
700 	uint dst;	/* destination data buffer pointer */
701 } idma_bd_t;
702 
703 /* IDMA buffer descriptor flag bit fields
704 */
705 #define IDMA_BD_V	((uint)0x80000000)	/* valid */
706 #define IDMA_BD_W	((uint)0x20000000)	/* wrap */
707 #define IDMA_BD_I	((uint)0x10000000)	/* interrupt */
708 #define IDMA_BD_L	((uint)0x08000000)	/* last */
709 #define IDMA_BD_CM	((uint)0x02000000)	/* continuous mode */
710 #define IDMA_BD_SDN	((uint)0x00400000)	/* source done */
711 #define IDMA_BD_DDN	((uint)0x00200000)	/* destination done */
712 #define IDMA_BD_DGBL	((uint)0x00100000)	/* destination global */
713 #define IDMA_BD_DBO_LE	((uint)0x00040000)	/* little-end dest byte order */
714 #define IDMA_BD_DBO_BE	((uint)0x00080000)	/* big-end dest byte order */
715 #define IDMA_BD_DDTB	((uint)0x00010000)	/* destination data bus */
716 #define IDMA_BD_SGBL	((uint)0x00002000)	/* source global */
717 #define IDMA_BD_SBO_LE	((uint)0x00000800)	/* little-end src byte order */
718 #define IDMA_BD_SBO_BE	((uint)0x00001000)	/* big-end src byte order */
719 #define IDMA_BD_SDTB	((uint)0x00000200)	/* source data bus */
720 
721 /* per-channel IDMA registers
722 */
723 typedef struct im_idma {
724 	u_char idsr;			/* IDMAn event status register */
725 	u_char res0[3];
726 	u_char idmr;			/* IDMAn event mask register */
727 	u_char res1[3];
728 } im_idma_t;
729 
730 /* IDMA event register bit fields
731 */
732 #define IDMA_EVENT_SC	((unsigned char)0x08)	/* stop completed */
733 #define IDMA_EVENT_OB	((unsigned char)0x04)	/* out of buffers */
734 #define IDMA_EVENT_EDN	((unsigned char)0x02)	/* external DONE asserted */
735 #define IDMA_EVENT_BC	((unsigned char)0x01)	/* buffer descriptor complete */
736 
737 /* RISC Controller Configuration Register (RCCR) bit fields
738 */
739 #define RCCR_TIME	((uint)0x80000000) /* timer enable */
740 #define RCCR_TIMEP_MASK	((uint)0x3f000000) /* mask for timer period bit field */
741 #define RCCR_DR0M	((uint)0x00800000) /* IDMA0 request mode */
742 #define RCCR_DR1M	((uint)0x00400000) /* IDMA1 request mode */
743 #define RCCR_DR2M	((uint)0x00000080) /* IDMA2 request mode */
744 #define RCCR_DR3M	((uint)0x00000040) /* IDMA3 request mode */
745 #define RCCR_DR0QP_MASK	((uint)0x00300000) /* mask for IDMA0 req priority */
746 #define RCCR_DR0QP_HIGH ((uint)0x00000000) /* IDMA0 has high req priority */
747 #define RCCR_DR0QP_MED	((uint)0x00100000) /* IDMA0 has medium req priority */
748 #define RCCR_DR0QP_LOW	((uint)0x00200000) /* IDMA0 has low req priority */
749 #define RCCR_DR1QP_MASK	((uint)0x00030000) /* mask for IDMA1 req priority */
750 #define RCCR_DR1QP_HIGH ((uint)0x00000000) /* IDMA1 has high req priority */
751 #define RCCR_DR1QP_MED	((uint)0x00010000) /* IDMA1 has medium req priority */
752 #define RCCR_DR1QP_LOW	((uint)0x00020000) /* IDMA1 has low req priority */
753 #define RCCR_DR2QP_MASK	((uint)0x00000030) /* mask for IDMA2 req priority */
754 #define RCCR_DR2QP_HIGH ((uint)0x00000000) /* IDMA2 has high req priority */
755 #define RCCR_DR2QP_MED	((uint)0x00000010) /* IDMA2 has medium req priority */
756 #define RCCR_DR2QP_LOW	((uint)0x00000020) /* IDMA2 has low req priority */
757 #define RCCR_DR3QP_MASK	((uint)0x00000003) /* mask for IDMA3 req priority */
758 #define RCCR_DR3QP_HIGH ((uint)0x00000000) /* IDMA3 has high req priority */
759 #define RCCR_DR3QP_MED	((uint)0x00000001) /* IDMA3 has medium req priority */
760 #define RCCR_DR3QP_LOW	((uint)0x00000002) /* IDMA3 has low req priority */
761 #define RCCR_EIE	((uint)0x00080000) /* external interrupt enable */
762 #define RCCR_SCD	((uint)0x00040000) /* scheduler configuration */
763 #define RCCR_ERAM_MASK	((uint)0x0000e000) /* mask for enable RAM microcode */
764 #define RCCR_ERAM_0KB	((uint)0x00000000) /* use 0KB of dpram for microcode */
765 #define RCCR_ERAM_2KB	((uint)0x00002000) /* use 2KB of dpram for microcode */
766 #define RCCR_ERAM_4KB	((uint)0x00004000) /* use 4KB of dpram for microcode */
767 #define RCCR_ERAM_6KB	((uint)0x00006000) /* use 6KB of dpram for microcode */
768 #define RCCR_ERAM_8KB	((uint)0x00008000) /* use 8KB of dpram for microcode */
769 #define RCCR_ERAM_10KB	((uint)0x0000a000) /* use 10KB of dpram for microcode */
770 #define RCCR_ERAM_12KB	((uint)0x0000c000) /* use 12KB of dpram for microcode */
771 #define RCCR_EDM0	((uint)0x00000800) /* DREQ0 edge detect mode */
772 #define RCCR_EDM1	((uint)0x00000400) /* DREQ1 edge detect mode */
773 #define RCCR_EDM2	((uint)0x00000200) /* DREQ2 edge detect mode */
774 #define RCCR_EDM3	((uint)0x00000100) /* DREQ3 edge detect mode */
775 #define RCCR_DEM01	((uint)0x00000008) /* DONE0/DONE1 edge detect mode */
776 #define RCCR_DEM23	((uint)0x00000004) /* DONE2/DONE3 edge detect mode */
777 
778 /*-----------------------------------------------------------------------
779  * CMXFCR - CMX FCC Clock Route Register
780  */
781 #define CMXFCR_FC1         0x40000000   /* FCC1 connection              */
782 #define CMXFCR_RF1CS_MSK   0x38000000   /* Receive FCC1 Clock Source Mask */
783 #define CMXFCR_TF1CS_MSK   0x07000000   /* Transmit FCC1 Clock Source Mask */
784 #define CMXFCR_FC2         0x00400000   /* FCC2 connection              */
785 #define CMXFCR_RF2CS_MSK   0x00380000   /* Receive FCC2 Clock Source Mask */
786 #define CMXFCR_TF2CS_MSK   0x00070000   /* Transmit FCC2 Clock Source Mask */
787 #define CMXFCR_FC3         0x00004000   /* FCC3 connection              */
788 #define CMXFCR_RF3CS_MSK   0x00003800   /* Receive FCC3 Clock Source Mask */
789 #define CMXFCR_TF3CS_MSK   0x00000700   /* Transmit FCC3 Clock Source Mask */
790 
791 #define CMXFCR_RF1CS_BRG5  0x00000000   /* Receive FCC1 Clock Source is BRG5 */
792 #define CMXFCR_RF1CS_BRG6  0x08000000   /* Receive FCC1 Clock Source is BRG6 */
793 #define CMXFCR_RF1CS_BRG7  0x10000000   /* Receive FCC1 Clock Source is BRG7 */
794 #define CMXFCR_RF1CS_BRG8  0x18000000   /* Receive FCC1 Clock Source is BRG8 */
795 #define CMXFCR_RF1CS_CLK9  0x20000000   /* Receive FCC1 Clock Source is CLK9 */
796 #define CMXFCR_RF1CS_CLK10 0x28000000   /* Receive FCC1 Clock Source is CLK10 */
797 #define CMXFCR_RF1CS_CLK11 0x30000000   /* Receive FCC1 Clock Source is CLK11 */
798 #define CMXFCR_RF1CS_CLK12 0x38000000   /* Receive FCC1 Clock Source is CLK12 */
799 
800 #define CMXFCR_TF1CS_BRG5  0x00000000   /* Transmit FCC1 Clock Source is BRG5 */
801 #define CMXFCR_TF1CS_BRG6  0x01000000   /* Transmit FCC1 Clock Source is BRG6 */
802 #define CMXFCR_TF1CS_BRG7  0x02000000   /* Transmit FCC1 Clock Source is BRG7 */
803 #define CMXFCR_TF1CS_BRG8  0x03000000   /* Transmit FCC1 Clock Source is BRG8 */
804 #define CMXFCR_TF1CS_CLK9  0x04000000   /* Transmit FCC1 Clock Source is CLK9 */
805 #define CMXFCR_TF1CS_CLK10 0x05000000   /* Transmit FCC1 Clock Source is CLK10 */
806 #define CMXFCR_TF1CS_CLK11 0x06000000   /* Transmit FCC1 Clock Source is CLK11 */
807 #define CMXFCR_TF1CS_CLK12 0x07000000   /* Transmit FCC1 Clock Source is CLK12 */
808 
809 #define CMXFCR_RF2CS_BRG5  0x00000000   /* Receive FCC2 Clock Source is BRG5 */
810 #define CMXFCR_RF2CS_BRG6  0x00080000   /* Receive FCC2 Clock Source is BRG6 */
811 #define CMXFCR_RF2CS_BRG7  0x00100000   /* Receive FCC2 Clock Source is BRG7 */
812 #define CMXFCR_RF2CS_BRG8  0x00180000   /* Receive FCC2 Clock Source is BRG8 */
813 #define CMXFCR_RF2CS_CLK13 0x00200000   /* Receive FCC2 Clock Source is CLK13 */
814 #define CMXFCR_RF2CS_CLK14 0x00280000   /* Receive FCC2 Clock Source is CLK14 */
815 #define CMXFCR_RF2CS_CLK15 0x00300000   /* Receive FCC2 Clock Source is CLK15 */
816 #define CMXFCR_RF2CS_CLK16 0x00380000   /* Receive FCC2 Clock Source is CLK16 */
817 
818 #define CMXFCR_TF2CS_BRG5  0x00000000   /* Transmit FCC2 Clock Source is BRG5 */
819 #define CMXFCR_TF2CS_BRG6  0x00010000   /* Transmit FCC2 Clock Source is BRG6 */
820 #define CMXFCR_TF2CS_BRG7  0x00020000   /* Transmit FCC2 Clock Source is BRG7 */
821 #define CMXFCR_TF2CS_BRG8  0x00030000   /* Transmit FCC2 Clock Source is BRG8 */
822 #define CMXFCR_TF2CS_CLK13 0x00040000   /* Transmit FCC2 Clock Source is CLK13 */
823 #define CMXFCR_TF2CS_CLK14 0x00050000   /* Transmit FCC2 Clock Source is CLK14 */
824 #define CMXFCR_TF2CS_CLK15 0x00060000   /* Transmit FCC2 Clock Source is CLK15 */
825 #define CMXFCR_TF2CS_CLK16 0x00070000   /* Transmit FCC2 Clock Source is CLK16 */
826 
827 #define CMXFCR_RF3CS_BRG5  0x00000000   /* Receive FCC3 Clock Source is BRG5 */
828 #define CMXFCR_RF3CS_BRG6  0x00000800   /* Receive FCC3 Clock Source is BRG6 */
829 #define CMXFCR_RF3CS_BRG7  0x00001000   /* Receive FCC3 Clock Source is BRG7 */
830 #define CMXFCR_RF3CS_BRG8  0x00001800   /* Receive FCC3 Clock Source is BRG8 */
831 #define CMXFCR_RF3CS_CLK13 0x00002000   /* Receive FCC3 Clock Source is CLK13 */
832 #define CMXFCR_RF3CS_CLK14 0x00002800   /* Receive FCC3 Clock Source is CLK14 */
833 #define CMXFCR_RF3CS_CLK15 0x00003000   /* Receive FCC3 Clock Source is CLK15 */
834 #define CMXFCR_RF3CS_CLK16 0x00003800   /* Receive FCC3 Clock Source is CLK16 */
835 
836 #define CMXFCR_TF3CS_BRG5  0x00000000   /* Transmit FCC3 Clock Source is BRG5 */
837 #define CMXFCR_TF3CS_BRG6  0x00000100   /* Transmit FCC3 Clock Source is BRG6 */
838 #define CMXFCR_TF3CS_BRG7  0x00000200   /* Transmit FCC3 Clock Source is BRG7 */
839 #define CMXFCR_TF3CS_BRG8  0x00000300   /* Transmit FCC3 Clock Source is BRG8 */
840 #define CMXFCR_TF3CS_CLK13 0x00000400   /* Transmit FCC3 Clock Source is CLK13 */
841 #define CMXFCR_TF3CS_CLK14 0x00000500   /* Transmit FCC3 Clock Source is CLK14 */
842 #define CMXFCR_TF3CS_CLK15 0x00000600   /* Transmit FCC3 Clock Source is CLK15 */
843 #define CMXFCR_TF3CS_CLK16 0x00000700   /* Transmit FCC3 Clock Source is CLK16 */
844 
845 /*-----------------------------------------------------------------------
846  * CMXSCR - CMX SCC Clock Route Register
847  */
848 #define CMXSCR_GR1         0x80000000   /* Grant Support of SCC1        */
849 #define CMXSCR_SC1         0x40000000   /* SCC1 connection              */
850 #define CMXSCR_RS1CS_MSK   0x38000000   /* Receive SCC1 Clock Source Mask */
851 #define CMXSCR_TS1CS_MSK   0x07000000   /* Transmit SCC1 Clock Source Mask */
852 #define CMXSCR_GR2         0x00800000   /* Grant Support of SCC2        */
853 #define CMXSCR_SC2         0x00400000   /* SCC2 connection              */
854 #define CMXSCR_RS2CS_MSK   0x00380000   /* Receive SCC2 Clock Source Mask */
855 #define CMXSCR_TS2CS_MSK   0x00070000   /* Transmit SCC2 Clock Source Mask */
856 #define CMXSCR_GR3         0x00008000   /* Grant Support of SCC3        */
857 #define CMXSCR_SC3         0x00004000   /* SCC3 connection              */
858 #define CMXSCR_RS3CS_MSK   0x00003800   /* Receive SCC3 Clock Source Mask */
859 #define CMXSCR_TS3CS_MSK   0x00000700   /* Transmit SCC3 Clock Source Mask */
860 #define CMXSCR_GR4         0x00000080   /* Grant Support of SCC4        */
861 #define CMXSCR_SC4         0x00000040   /* SCC4 connection              */
862 #define CMXSCR_RS4CS_MSK   0x00000038   /* Receive SCC4 Clock Source Mask */
863 #define CMXSCR_TS4CS_MSK   0x00000007   /* Transmit SCC4 Clock Source Mask */
864 
865 #define CMXSCR_RS1CS_BRG1  0x00000000   /* SCC1 Rx Clock Source is BRG1 */
866 #define CMXSCR_RS1CS_BRG2  0x08000000   /* SCC1 Rx Clock Source is BRG2 */
867 #define CMXSCR_RS1CS_BRG3  0x10000000   /* SCC1 Rx Clock Source is BRG3 */
868 #define CMXSCR_RS1CS_BRG4  0x18000000   /* SCC1 Rx Clock Source is BRG4 */
869 #define CMXSCR_RS1CS_CLK11 0x20000000   /* SCC1 Rx Clock Source is CLK11 */
870 #define CMXSCR_RS1CS_CLK12 0x28000000   /* SCC1 Rx Clock Source is CLK12 */
871 #define CMXSCR_RS1CS_CLK3  0x30000000   /* SCC1 Rx Clock Source is CLK3 */
872 #define CMXSCR_RS1CS_CLK4  0x38000000   /* SCC1 Rx Clock Source is CLK4 */
873 
874 #define CMXSCR_TS1CS_BRG1  0x00000000   /* SCC1 Tx Clock Source is BRG1 */
875 #define CMXSCR_TS1CS_BRG2  0x01000000   /* SCC1 Tx Clock Source is BRG2 */
876 #define CMXSCR_TS1CS_BRG3  0x02000000   /* SCC1 Tx Clock Source is BRG3 */
877 #define CMXSCR_TS1CS_BRG4  0x03000000   /* SCC1 Tx Clock Source is BRG4 */
878 #define CMXSCR_TS1CS_CLK11 0x04000000   /* SCC1 Tx Clock Source is CLK11 */
879 #define CMXSCR_TS1CS_CLK12 0x05000000   /* SCC1 Tx Clock Source is CLK12 */
880 #define CMXSCR_TS1CS_CLK3  0x06000000   /* SCC1 Tx Clock Source is CLK3 */
881 #define CMXSCR_TS1CS_CLK4  0x07000000   /* SCC1 Tx Clock Source is CLK4 */
882 
883 #define CMXSCR_RS2CS_BRG1  0x00000000   /* SCC2 Rx Clock Source is BRG1 */
884 #define CMXSCR_RS2CS_BRG2  0x00080000   /* SCC2 Rx Clock Source is BRG2 */
885 #define CMXSCR_RS2CS_BRG3  0x00100000   /* SCC2 Rx Clock Source is BRG3 */
886 #define CMXSCR_RS2CS_BRG4  0x00180000   /* SCC2 Rx Clock Source is BRG4 */
887 #define CMXSCR_RS2CS_CLK11 0x00200000   /* SCC2 Rx Clock Source is CLK11 */
888 #define CMXSCR_RS2CS_CLK12 0x00280000   /* SCC2 Rx Clock Source is CLK12 */
889 #define CMXSCR_RS2CS_CLK3  0x00300000   /* SCC2 Rx Clock Source is CLK3 */
890 #define CMXSCR_RS2CS_CLK4  0x00380000   /* SCC2 Rx Clock Source is CLK4 */
891 
892 #define CMXSCR_TS2CS_BRG1  0x00000000   /* SCC2 Tx Clock Source is BRG1 */
893 #define CMXSCR_TS2CS_BRG2  0x00010000   /* SCC2 Tx Clock Source is BRG2 */
894 #define CMXSCR_TS2CS_BRG3  0x00020000   /* SCC2 Tx Clock Source is BRG3 */
895 #define CMXSCR_TS2CS_BRG4  0x00030000   /* SCC2 Tx Clock Source is BRG4 */
896 #define CMXSCR_TS2CS_CLK11 0x00040000   /* SCC2 Tx Clock Source is CLK11 */
897 #define CMXSCR_TS2CS_CLK12 0x00050000   /* SCC2 Tx Clock Source is CLK12 */
898 #define CMXSCR_TS2CS_CLK3  0x00060000   /* SCC2 Tx Clock Source is CLK3 */
899 #define CMXSCR_TS2CS_CLK4  0x00070000   /* SCC2 Tx Clock Source is CLK4 */
900 
901 #define CMXSCR_RS3CS_BRG1  0x00000000   /* SCC3 Rx Clock Source is BRG1 */
902 #define CMXSCR_RS3CS_BRG2  0x00000800   /* SCC3 Rx Clock Source is BRG2 */
903 #define CMXSCR_RS3CS_BRG3  0x00001000   /* SCC3 Rx Clock Source is BRG3 */
904 #define CMXSCR_RS3CS_BRG4  0x00001800   /* SCC3 Rx Clock Source is BRG4 */
905 #define CMXSCR_RS3CS_CLK5  0x00002000   /* SCC3 Rx Clock Source is CLK5 */
906 #define CMXSCR_RS3CS_CLK6  0x00002800   /* SCC3 Rx Clock Source is CLK6 */
907 #define CMXSCR_RS3CS_CLK7  0x00003000   /* SCC3 Rx Clock Source is CLK7 */
908 #define CMXSCR_RS3CS_CLK8  0x00003800   /* SCC3 Rx Clock Source is CLK8 */
909 
910 #define CMXSCR_TS3CS_BRG1  0x00000000   /* SCC3 Tx Clock Source is BRG1 */
911 #define CMXSCR_TS3CS_BRG2  0x00000100   /* SCC3 Tx Clock Source is BRG2 */
912 #define CMXSCR_TS3CS_BRG3  0x00000200   /* SCC3 Tx Clock Source is BRG3 */
913 #define CMXSCR_TS3CS_BRG4  0x00000300   /* SCC3 Tx Clock Source is BRG4 */
914 #define CMXSCR_TS3CS_CLK5  0x00000400   /* SCC3 Tx Clock Source is CLK5 */
915 #define CMXSCR_TS3CS_CLK6  0x00000500   /* SCC3 Tx Clock Source is CLK6 */
916 #define CMXSCR_TS3CS_CLK7  0x00000600   /* SCC3 Tx Clock Source is CLK7 */
917 #define CMXSCR_TS3CS_CLK8  0x00000700   /* SCC3 Tx Clock Source is CLK8 */
918 
919 #define CMXSCR_RS4CS_BRG1  0x00000000   /* SCC4 Rx Clock Source is BRG1 */
920 #define CMXSCR_RS4CS_BRG2  0x00000008   /* SCC4 Rx Clock Source is BRG2 */
921 #define CMXSCR_RS4CS_BRG3  0x00000010   /* SCC4 Rx Clock Source is BRG3 */
922 #define CMXSCR_RS4CS_BRG4  0x00000018   /* SCC4 Rx Clock Source is BRG4 */
923 #define CMXSCR_RS4CS_CLK5  0x00000020   /* SCC4 Rx Clock Source is CLK5 */
924 #define CMXSCR_RS4CS_CLK6  0x00000028   /* SCC4 Rx Clock Source is CLK6 */
925 #define CMXSCR_RS4CS_CLK7  0x00000030   /* SCC4 Rx Clock Source is CLK7 */
926 #define CMXSCR_RS4CS_CLK8  0x00000038   /* SCC4 Rx Clock Source is CLK8 */
927 
928 #define CMXSCR_TS4CS_BRG1  0x00000000   /* SCC4 Tx Clock Source is BRG1 */
929 #define CMXSCR_TS4CS_BRG2  0x00000001   /* SCC4 Tx Clock Source is BRG2 */
930 #define CMXSCR_TS4CS_BRG3  0x00000002   /* SCC4 Tx Clock Source is BRG3 */
931 #define CMXSCR_TS4CS_BRG4  0x00000003   /* SCC4 Tx Clock Source is BRG4 */
932 #define CMXSCR_TS4CS_CLK5  0x00000004   /* SCC4 Tx Clock Source is CLK5 */
933 #define CMXSCR_TS4CS_CLK6  0x00000005   /* SCC4 Tx Clock Source is CLK6 */
934 #define CMXSCR_TS4CS_CLK7  0x00000006   /* SCC4 Tx Clock Source is CLK7 */
935 #define CMXSCR_TS4CS_CLK8  0x00000007   /* SCC4 Tx Clock Source is CLK8 */
936 
937 /*-----------------------------------------------------------------------
938  * SIUMCR - SIU Module Configuration Register				 4-31
939  */
940 #define SIUMCR_BBD	0x80000000	/* Bus Busy Disable		*/
941 #define SIUMCR_ESE	0x40000000	/* External Snoop Enable	*/
942 #define SIUMCR_PBSE	0x20000000	/* Parity Byte Select Enable	*/
943 #define SIUMCR_CDIS	0x10000000	/* Core Disable			*/
944 #define SIUMCR_DPPC00	0x00000000	/* Data Parity Pins Configuration*/
945 #define SIUMCR_DPPC01	0x04000000	/* - " -			*/
946 #define SIUMCR_DPPC10	0x08000000	/* - " -			*/
947 #define SIUMCR_DPPC11	0x0c000000	/* - " -			*/
948 #define SIUMCR_L2CPC00	0x00000000	/* L2 Cache Pins Configuration	*/
949 #define SIUMCR_L2CPC01	0x01000000	/* - " -			*/
950 #define SIUMCR_L2CPC10	0x02000000	/* - " -			*/
951 #define SIUMCR_L2CPC11	0x03000000	/* - " -			*/
952 #define SIUMCR_LBPC00	0x00000000	/* Local Bus Pins Configuration	*/
953 #define SIUMCR_LBPC01	0x00400000	/* - " -			*/
954 #define SIUMCR_LBPC10	0x00800000	/* - " -			*/
955 #define SIUMCR_LBPC11	0x00c00000	/* - " -			*/
956 #define SIUMCR_APPC00	0x00000000	/* Address Parity Pins Configuration*/
957 #define SIUMCR_APPC01	0x00100000	/* - " -			*/
958 #define SIUMCR_APPC10	0x00200000	/* - " -			*/
959 #define SIUMCR_APPC11	0x00300000	/* - " -			*/
960 #define SIUMCR_CS10PC00	0x00000000	/* CS10 Pin Configuration	*/
961 #define SIUMCR_CS10PC01	0x00040000	/* - " -			*/
962 #define SIUMCR_CS10PC10	0x00080000	/* - " -			*/
963 #define SIUMCR_CS10PC11	0x000c0000	/* - " -			*/
964 #define SIUMCR_BCTLC00	0x00000000	/* Buffer Control Configuration	*/
965 #define SIUMCR_BCTLC01	0x00010000	/* - " -			*/
966 #define SIUMCR_BCTLC10	0x00020000	/* - " -			*/
967 #define SIUMCR_BCTLC11	0x00030000	/* - " -			*/
968 #define SIUMCR_MMR00	0x00000000	/* Mask Masters Requests	*/
969 #define SIUMCR_MMR01	0x00004000	/* - " -			*/
970 #define SIUMCR_MMR10	0x00008000	/* - " -			*/
971 #define SIUMCR_MMR11	0x0000c000	/* - " -			*/
972 #define SIUMCR_LPBSE	0x00002000	/* LocalBus Parity Byte Select Enable*/
973 
974 /*-----------------------------------------------------------------------
975  * SCCR - System Clock Control Register					 9-8
976 */
977 #define SCCR_PCI_MODE	0x00000100	/* PCI Mode	*/
978 #define SCCR_PCI_MODCK	0x00000080	/* Value of PCI_MODCK pin	*/
979 #define SCCR_PCIDF_MSK	0x00000078	/* PCI division factor	*/
980 #define SCCR_PCIDF_SHIFT 3
981 
982 #ifndef CPM_IMMR_OFFSET
983 #define CPM_IMMR_OFFSET	0x101a8
984 #endif
985 
986 #define FCC_PSMR_RMII	((uint)0x00020000)	/* Use RMII interface */
987 
988 /* FCC iop & clock configuration. BSP code is responsible to define Fx_RXCLK & Fx_TXCLK
989  * in order to use clock-computing stuff below for the FCC x
990  */
991 
992 /* Automatically generates register configurations */
993 #define PC_CLK(x)	((uint)(1<<(x-1)))	/* FCC CLK I/O ports */
994 
995 #define CMXFCR_RF1CS(x)	((uint)((x-5)<<27))	/* FCC1 Receive Clock Source */
996 #define CMXFCR_TF1CS(x)	((uint)((x-5)<<24))	/* FCC1 Transmit Clock Source */
997 #define CMXFCR_RF2CS(x)	((uint)((x-9)<<19))	/* FCC2 Receive Clock Source */
998 #define CMXFCR_TF2CS(x) ((uint)((x-9)<<16))	/* FCC2 Transmit Clock Source */
999 #define CMXFCR_RF3CS(x)	((uint)((x-9)<<11))	/* FCC3 Receive Clock Source */
1000 #define CMXFCR_TF3CS(x) ((uint)((x-9)<<8))	/* FCC3 Transmit Clock Source */
1001 
1002 #define PC_F1RXCLK	PC_CLK(F1_RXCLK)
1003 #define PC_F1TXCLK	PC_CLK(F1_TXCLK)
1004 #define CMX1_CLK_ROUTE	(CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
1005 #define CMX1_CLK_MASK	((uint)0xff000000)
1006 
1007 #define PC_F2RXCLK	PC_CLK(F2_RXCLK)
1008 #define PC_F2TXCLK	PC_CLK(F2_TXCLK)
1009 #define CMX2_CLK_ROUTE	(CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
1010 #define CMX2_CLK_MASK	((uint)0x00ff0000)
1011 
1012 #define PC_F3RXCLK	PC_CLK(F3_RXCLK)
1013 #define PC_F3TXCLK	PC_CLK(F3_TXCLK)
1014 #define CMX3_CLK_ROUTE	(CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
1015 #define CMX3_CLK_MASK	((uint)0x0000ff00)
1016 
1017 #define CPMUX_CLK_MASK (CMX3_CLK_MASK | CMX2_CLK_MASK)
1018 #define CPMUX_CLK_ROUTE (CMX3_CLK_ROUTE | CMX2_CLK_ROUTE)
1019 
1020 #define CLK_TRX (PC_F3TXCLK | PC_F3RXCLK | PC_F2TXCLK | PC_F2RXCLK)
1021 
1022 /* I/O Pin assignment for FCC1.  I don't yet know the best way to do this,
1023  * but there is little variation among the choices.
1024  */
1025 #define PA1_COL		0x00000001U
1026 #define PA1_CRS		0x00000002U
1027 #define PA1_TXER	0x00000004U
1028 #define PA1_TXEN	0x00000008U
1029 #define PA1_RXDV	0x00000010U
1030 #define PA1_RXER	0x00000020U
1031 #define PA1_TXDAT	0x00003c00U
1032 #define PA1_RXDAT	0x0003c000U
1033 #define PA1_PSORA0	(PA1_RXDAT | PA1_TXDAT)
1034 #define PA1_PSORA1	(PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
1035 		PA1_RXDV | PA1_RXER)
1036 #define PA1_DIRA0	(PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
1037 #define PA1_DIRA1	(PA1_TXDAT | PA1_TXEN | PA1_TXER)
1038 
1039 
1040 /* I/O Pin assignment for FCC2.  I don't yet know the best way to do this,
1041  * but there is little variation among the choices.
1042  */
1043 #define PB2_TXER	0x00000001U
1044 #define PB2_RXDV	0x00000002U
1045 #define PB2_TXEN	0x00000004U
1046 #define PB2_RXER	0x00000008U
1047 #define PB2_COL		0x00000010U
1048 #define PB2_CRS		0x00000020U
1049 #define PB2_TXDAT	0x000003c0U
1050 #define PB2_RXDAT	0x00003c00U
1051 #define PB2_PSORB0	(PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
1052 		PB2_RXER | PB2_RXDV | PB2_TXER)
1053 #define PB2_PSORB1	(PB2_TXEN)
1054 #define PB2_DIRB0	(PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
1055 #define PB2_DIRB1	(PB2_TXDAT | PB2_TXEN | PB2_TXER)
1056 
1057 
1058 /* I/O Pin assignment for FCC3.  I don't yet know the best way to do this,
1059  * but there is little variation among the choices.
1060  */
1061 #define PB3_RXDV	0x00004000U
1062 #define PB3_RXER	0x00008000U
1063 #define PB3_TXER	0x00010000U
1064 #define PB3_TXEN	0x00020000U
1065 #define PB3_COL		0x00040000U
1066 #define PB3_CRS		0x00080000U
1067 #define PB3_TXDAT	0x0f000000U
1068 #define PC3_TXDAT	0x00000010U
1069 #define PB3_RXDAT	0x00f00000U
1070 #define PB3_PSORB0	(PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
1071 		PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
1072 #define PB3_PSORB1	0
1073 #define PB3_DIRB0	(PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
1074 #define PB3_DIRB1	(PB3_TXDAT | PB3_TXEN | PB3_TXER)
1075 #define PC3_DIRC1	(PC3_TXDAT)
1076 
1077 /* Handy macro to specify mem for FCCs*/
1078 #define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
1079 #define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
1080 #define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
1081 #define FCC3_MEM_OFFSET FCC_MEM_OFFSET(2)
1082 
1083 /* Pipeline Maximum Depth */
1084 #define MPC82XX_BCR_PLDP 0x00800000
1085 
1086 /* Clocks and GRG's */
1087 
1088 enum cpm_clk_dir {
1089 	CPM_CLK_RX,
1090 	CPM_CLK_TX,
1091 	CPM_CLK_RTX
1092 };
1093 
1094 enum cpm_clk_target {
1095 	CPM_CLK_SCC1,
1096 	CPM_CLK_SCC2,
1097 	CPM_CLK_SCC3,
1098 	CPM_CLK_SCC4,
1099 	CPM_CLK_FCC1,
1100 	CPM_CLK_FCC2,
1101 	CPM_CLK_FCC3,
1102 	CPM_CLK_SMC1,
1103 	CPM_CLK_SMC2,
1104 };
1105 
1106 enum cpm_clk {
1107 	CPM_CLK_NONE = 0,
1108 	CPM_BRG1,	/* Baud Rate Generator  1 */
1109 	CPM_BRG2,	/* Baud Rate Generator  2 */
1110 	CPM_BRG3,	/* Baud Rate Generator  3 */
1111 	CPM_BRG4,	/* Baud Rate Generator  4 */
1112 	CPM_BRG5,	/* Baud Rate Generator  5 */
1113 	CPM_BRG6,	/* Baud Rate Generator  6 */
1114 	CPM_BRG7,	/* Baud Rate Generator  7 */
1115 	CPM_BRG8,	/* Baud Rate Generator  8 */
1116 	CPM_CLK1,	/* Clock  1 */
1117 	CPM_CLK2,	/* Clock  2 */
1118 	CPM_CLK3,	/* Clock  3 */
1119 	CPM_CLK4,	/* Clock  4 */
1120 	CPM_CLK5,	/* Clock  5 */
1121 	CPM_CLK6,	/* Clock  6 */
1122 	CPM_CLK7,	/* Clock  7 */
1123 	CPM_CLK8,	/* Clock  8 */
1124 	CPM_CLK9,	/* Clock  9 */
1125 	CPM_CLK10,	/* Clock 10 */
1126 	CPM_CLK11,	/* Clock 11 */
1127 	CPM_CLK12,	/* Clock 12 */
1128 	CPM_CLK13,	/* Clock 13 */
1129 	CPM_CLK14,	/* Clock 14 */
1130 	CPM_CLK15,	/* Clock 15 */
1131 	CPM_CLK16,	/* Clock 16 */
1132 	CPM_CLK17,	/* Clock 17 */
1133 	CPM_CLK18,	/* Clock 18 */
1134 	CPM_CLK19,	/* Clock 19 */
1135 	CPM_CLK20,	/* Clock 20 */
1136 	CPM_CLK_DUMMY
1137 };
1138 
1139 int __init cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode);
1140 int __init cpm2_smc_clk_setup(enum cpm_clk_target target, int clock);
1141 
1142 #define CPM_PIN_INPUT     0
1143 #define CPM_PIN_OUTPUT    1
1144 #define CPM_PIN_PRIMARY   0
1145 #define CPM_PIN_SECONDARY 2
1146 #define CPM_PIN_GPIO      4
1147 #define CPM_PIN_OPENDRAIN 8
1148 
1149 void __init cpm2_set_pin(int port, int pin, int flags);
1150 
1151 #endif /* __CPM2__ */
1152 #endif /* __KERNEL__ */
1153