xref: /openbmc/linux/arch/mips/include/asm/sgi/mc.h (revision 70342287)
1 /*
2  * This file is subject to the terms and conditions of the GNU General Public
3  * License. See the file "COPYING" in the main directory of this archive
4  * for more details.
5  *
6  * mc.h: Definitions for SGI Memory Controller
7  *
8  * Copyright (C) 1996 David S. Miller
9  * Copyright (C) 1999 Ralf Baechle
10  * Copyright (C) 1999 Silicon Graphics, Inc.
11  */
12 
13 #ifndef _SGI_MC_H
14 #define _SGI_MC_H
15 
16 struct sgimc_regs {
17 	u32 _unused0;
18 	volatile u32 cpuctrl0;	/* CPU control register 0, readwrite */
19 #define SGIMC_CCTRL0_REFS	0x0000000f /* REFS mask */
20 #define SGIMC_CCTRL0_EREFRESH	0x00000010 /* Memory refresh enable */
21 #define SGIMC_CCTRL0_EPERRGIO	0x00000020 /* GIO parity error enable */
22 #define SGIMC_CCTRL0_EPERRMEM	0x00000040 /* Main mem parity error enable */
23 #define SGIMC_CCTRL0_EPERRCPU	0x00000080 /* CPU bus parity error enable */
24 #define SGIMC_CCTRL0_WDOG	0x00000100 /* Watchdog timer enable */
25 #define SGIMC_CCTRL0_SYSINIT	0x00000200 /* System init bit */
26 #define SGIMC_CCTRL0_GFXRESET	0x00000400 /* Graphics interface reset */
27 #define SGIMC_CCTRL0_EISALOCK	0x00000800 /* Lock CPU from memory for EISA */
28 #define SGIMC_CCTRL0_EPERRSCMD	0x00001000 /* SysCMD bus parity error enable */
29 #define SGIMC_CCTRL0_IENAB	0x00002000 /* Allow interrupts from MC */
30 #define SGIMC_CCTRL0_ESNOOP	0x00004000 /* Snooping I/O enable */
31 #define SGIMC_CCTRL0_EPROMWR	0x00008000 /* Prom writes from cpu enable */
32 #define SGIMC_CCTRL0_WRESETPMEM 0x00010000 /* Perform warm reset, preserves mem */
33 #define SGIMC_CCTRL0_LENDIAN	0x00020000 /* Put MC in little-endian mode */
34 #define SGIMC_CCTRL0_WRESETDMEM 0x00040000 /* Warm reset, destroys mem contents */
35 #define SGIMC_CCTRL0_CMEMBADPAR 0x02000000 /* Generate bad perr from cpu to mem */
36 #define SGIMC_CCTRL0_R4KNOCHKPARR 0x04000000 /* Don't chk parity on mem data reads */
37 #define SGIMC_CCTRL0_GIOBTOB	0x08000000 /* Allow GIO back to back writes */
38 	u32 _unused1;
39 	volatile u32 cpuctrl1;	/* CPU control register 1, readwrite */
40 #define SGIMC_CCTRL1_EGIOTIMEO	0x00000010 /* GIO bus timeout enable */
41 #define SGIMC_CCTRL1_FIXEDEHPC	0x00001000 /* Fixed HPC endianness */
42 #define SGIMC_CCTRL1_LITTLEHPC	0x00002000 /* Little endian HPC */
43 #define SGIMC_CCTRL1_FIXEDEEXP0 0x00004000 /* Fixed EXP0 endianness */
44 #define SGIMC_CCTRL1_LITTLEEXP0 0x00008000 /* Little endian EXP0 */
45 #define SGIMC_CCTRL1_FIXEDEEXP1 0x00010000 /* Fixed EXP1 endianness */
46 #define SGIMC_CCTRL1_LITTLEEXP1 0x00020000 /* Little endian EXP1 */
47 
48 	u32 _unused2;
49 	volatile u32 watchdogt; /* Watchdog reg rdonly, write clears */
50 
51 	u32 _unused3;
52 	volatile u32 systemid;	/* MC system ID register, readonly */
53 #define SGIMC_SYSID_MASKREV	0x0000000f /* Revision of MC controller */
54 #define SGIMC_SYSID_EPRESENT	0x00000010 /* Indicates presence of EISA bus */
55 
56 	u32 _unused4[3];
57 	volatile u32 divider;	/* Divider reg for RPSS */
58 
59 	u32 _unused5;
60 	u32 eeprom;		/* EEPROM byte reg for r4k */
61 #define SGIMC_EEPROM_PRE	0x00000001 /* eeprom chip PRE pin assertion */
62 #define SGIMC_EEPROM_CSEL	0x00000002 /* Active high, eeprom chip select */
63 #define SGIMC_EEPROM_SECLOCK	0x00000004 /* EEPROM serial clock */
64 #define SGIMC_EEPROM_SDATAO	0x00000008 /* Serial EEPROM data-out */
65 #define SGIMC_EEPROM_SDATAI	0x00000010 /* Serial EEPROM data-in */
66 
67 	u32 _unused6[3];
68 	volatile u32 rcntpre;	/* Preload refresh counter */
69 
70 	u32 _unused7;
71 	volatile u32 rcounter;	/* Readonly refresh counter */
72 
73 	u32 _unused8[13];
74 	volatile u32 giopar;	/* Parameter word for GIO64 */
75 #define SGIMC_GIOPAR_HPC64	0x00000001 /* HPC talks to GIO using 64-bits */
76 #define SGIMC_GIOPAR_GFX64	0x00000002 /* GFX talks to GIO using 64-bits */
77 #define SGIMC_GIOPAR_EXP064	0x00000004 /* EXP(slot0) talks using 64-bits */
78 #define SGIMC_GIOPAR_EXP164	0x00000008 /* EXP(slot1) talks using 64-bits */
79 #define SGIMC_GIOPAR_EISA64	0x00000010 /* EISA bus talks 64-bits to GIO */
80 #define SGIMC_GIOPAR_HPC264	0x00000020 /* 2nd HPX talks 64-bits to GIO */
81 #define SGIMC_GIOPAR_RTIMEGFX	0x00000040 /* GFX device has realtime attr */
82 #define SGIMC_GIOPAR_RTIMEEXP0	0x00000080 /* EXP(slot0) has realtime attr */
83 #define SGIMC_GIOPAR_RTIMEEXP1	0x00000100 /* EXP(slot1) has realtime attr */
84 #define SGIMC_GIOPAR_MASTEREISA 0x00000200 /* EISA bus can act as bus master */
85 #define SGIMC_GIOPAR_ONEBUS	0x00000400 /* Exists one GIO64 pipelined bus */
86 #define SGIMC_GIOPAR_MASTERGFX	0x00000800 /* GFX can act as a bus master */
87 #define SGIMC_GIOPAR_MASTEREXP0 0x00001000 /* EXP(slot0) can bus master */
88 #define SGIMC_GIOPAR_MASTEREXP1 0x00002000 /* EXP(slot1) can bus master */
89 #define SGIMC_GIOPAR_PLINEEXP0	0x00004000 /* EXP(slot0) has pipeline attr */
90 #define SGIMC_GIOPAR_PLINEEXP1	0x00008000 /* EXP(slot1) has pipeline attr */
91 
92 	u32 _unused9;
93 	volatile u32 cputp;	/* CPU bus arb time period */
94 
95 	u32 _unused10[3];
96 	volatile u32 lbursttp;	/* Time period for long bursts */
97 
98 	/* MC chip can drive up to 4 bank 4 SIMMs each. All SIMMs in bank must
99 	 * be the same size. The size encoding for supported SIMMs is bellow */
100 	u32 _unused11[9];
101 	volatile u32 mconfig0;	/* Memory config register zero */
102 	u32 _unused12;
103 	volatile u32 mconfig1;	/* Memory config register one */
104 #define SGIMC_MCONFIG_BASEADDR	0x000000ff /* Base address of bank*/
105 #define SGIMC_MCONFIG_RMASK	0x00001f00 /* Ram config bitmask */
106 #define SGIMC_MCONFIG_BVALID	0x00002000 /* Bank is valid */
107 #define SGIMC_MCONFIG_SBANKS	0x00004000 /* Number of subbanks */
108 
109 	u32 _unused13;
110 	volatile u32 cmacc;	   /* Mem access config for CPU */
111 	u32 _unused14;
112 	volatile u32 gmacc;	   /* Mem access config for GIO */
113 
114 	/* This define applies to both cmacc and gmacc registers above. */
115 #define SGIMC_MACC_ALIASBIG	0x20000000 /* 512MB home for alias */
116 
117 	/* Error address/status regs from GIO and CPU perspectives. */
118 	u32 _unused15;
119 	volatile u32 cerr;	/* Error address reg for CPU */
120 	u32 _unused16;
121 	volatile u32 cstat;	/* Status reg for CPU */
122 #define SGIMC_CSTAT_RD		0x00000100 /* read parity error */
123 #define SGIMC_CSTAT_PAR		0x00000200 /* CPU parity error */
124 #define SGIMC_CSTAT_ADDR	0x00000400 /* memory bus error bad addr */
125 #define SGIMC_CSTAT_SYSAD_PAR	0x00000800 /* sysad parity error */
126 #define SGIMC_CSTAT_SYSCMD_PAR	0x00001000 /* syscmd parity error */
127 #define SGIMC_CSTAT_BAD_DATA	0x00002000 /* bad data identifier */
128 #define SGIMC_CSTAT_PAR_MASK	0x00001f00 /* parity error mask */
129 #define SGIMC_CSTAT_RD_PAR	(SGIMC_CSTAT_RD | SGIMC_CSTAT_PAR)
130 
131 	u32 _unused17;
132 	volatile u32 gerr;	/* Error address reg for GIO */
133 	u32 _unused18;
134 	volatile u32 gstat;	/* Status reg for GIO */
135 #define SGIMC_GSTAT_RD		0x00000100 /* read parity error */
136 #define SGIMC_GSTAT_WR		0x00000200 /* write parity error */
137 #define SGIMC_GSTAT_TIME	0x00000400 /* GIO bus timed out */
138 #define SGIMC_GSTAT_PROM	0x00000800 /* write to PROM when PROM_EN not set */
139 #define SGIMC_GSTAT_ADDR	0x00001000 /* parity error on addr cycle */
140 #define SGIMC_GSTAT_BC		0x00002000 /* parity error on byte count cycle */
141 #define SGIMC_GSTAT_PIO_RD	0x00004000 /* read data parity on pio */
142 #define SGIMC_GSTAT_PIO_WR	0x00008000 /* write data parity on pio */
143 
144 	/* Special hard bus locking registers. */
145 	u32 _unused19;
146 	volatile u32 syssembit;		/* Uni-bit system semaphore */
147 	u32 _unused20;
148 	volatile u32 mlock;		/* Global GIO memory access lock */
149 	u32 _unused21;
150 	volatile u32 elock;		/* Locks EISA from GIO accesses */
151 
152 	/* GIO dma control registers. */
153 	u32 _unused22[15];
154 	volatile u32 gio_dma_trans;	/* DMA mask to translation GIO addrs */
155 	u32 _unused23;
156 	volatile u32 gio_dma_sbits;	/* DMA GIO addr substitution bits */
157 	u32 _unused24;
158 	volatile u32 dma_intr_cause;	/* DMA IRQ cause indicator bits */
159 	u32 _unused25;
160 	volatile u32 dma_ctrl;		/* Main DMA control reg */
161 
162 	/* DMA TLB entry 0 */
163 	u32 _unused26[5];
164 	volatile u32 dtlb_hi0;
165 	u32 _unused27;
166 	volatile u32 dtlb_lo0;
167 
168 	/* DMA TLB entry 1 */
169 	u32 _unused28;
170 	volatile u32 dtlb_hi1;
171 	u32 _unused29;
172 	volatile u32 dtlb_lo1;
173 
174 	/* DMA TLB entry 2 */
175 	u32 _unused30;
176 	volatile u32 dtlb_hi2;
177 	u32 _unused31;
178 	volatile u32 dtlb_lo2;
179 
180 	/* DMA TLB entry 3 */
181 	u32 _unused32;
182 	volatile u32 dtlb_hi3;
183 	u32 _unused33;
184 	volatile u32 dtlb_lo3;
185 
186 	u32 _unused34[0x0392];
187 
188 	u32 _unused35;
189 	volatile u32 rpsscounter;	/* Chirps at 100ns */
190 
191 	u32 _unused36[0x1000/4-2*4];
192 
193 	u32 _unused37;
194 	volatile u32 maddronly;		/* Address DMA goes at */
195 	u32 _unused38;
196 	volatile u32 maddrpdeflts;	/* Same as above, plus set defaults */
197 	u32 _unused39;
198 	volatile u32 dmasz;		/* DMA count */
199 	u32 _unused40;
200 	volatile u32 ssize;		/* DMA stride size */
201 	u32 _unused41;
202 	volatile u32 gmaddronly;	/* Set GIO DMA but don't start trans */
203 	u32 _unused42;
204 	volatile u32 dmaddnpgo;		/* Set GIO DMA addr + start transfer */
205 	u32 _unused43;
206 	volatile u32 dmamode;		/* DMA mode config bit settings */
207 	u32 _unused44;
208 	volatile u32 dmaccount;		/* Zoom and byte count for DMA */
209 	u32 _unused45;
210 	volatile u32 dmastart;		/* Pedal to the metal. */
211 	u32 _unused46;
212 	volatile u32 dmarunning;	/* DMA op is in progress */
213 	u32 _unused47;
214 	volatile u32 maddrdefstart;	/* Set dma addr, defaults, and kick it */
215 };
216 
217 extern struct sgimc_regs *sgimc;
218 #define SGIMC_BASE		0x1fa00000	/* physical */
219 
220 /* Base location of the two ram banks found in IP2[0268] machines. */
221 #define SGIMC_SEG0_BADDR	0x08000000
222 #define SGIMC_SEG1_BADDR	0x20000000
223 
224 /* Maximum size of the above banks are per machine. */
225 #define SGIMC_SEG0_SIZE_ALL		0x10000000 /* 256MB */
226 #define SGIMC_SEG1_SIZE_IP20_IP22	0x08000000 /* 128MB */
227 #define SGIMC_SEG1_SIZE_IP26_IP28	0x20000000 /* 512MB */
228 
229 extern void sgimc_init(void);
230 
231 #endif /* _SGI_MC_H */
232