1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Copyright (C) 2021 Marvell
4  *
5  * Authors:
6  *   Konstantin Porotchkin <kostap@marvell.com>
7  *
8  * Marvell CP110 UTMI PHY driver
9  */
10 
11 #include <linux/io.h>
12 #include <linux/iopoll.h>
13 #include <linux/mfd/syscon.h>
14 #include <linux/module.h>
15 #include <linux/of.h>
16 #include <linux/phy/phy.h>
17 #include <linux/platform_device.h>
18 #include <linux/regmap.h>
19 #include <linux/usb/of.h>
20 #include <linux/usb/otg.h>
21 
22 #define UTMI_PHY_PORTS				2
23 
24 /* CP110 UTMI register macro definetions */
25 #define SYSCON_USB_CFG_REG			0x420
26 #define   USB_CFG_DEVICE_EN_MASK		BIT(0)
27 #define   USB_CFG_DEVICE_MUX_OFFSET		1
28 #define   USB_CFG_DEVICE_MUX_MASK		BIT(1)
29 #define   USB_CFG_PLL_MASK			BIT(25)
30 
31 #define SYSCON_UTMI_CFG_REG(id)			(0x440 + (id) * 4)
32 #define   UTMI_PHY_CFG_PU_MASK			BIT(5)
33 
34 #define UTMI_PLL_CTRL_REG			0x0
35 #define   PLL_REFDIV_OFFSET			0
36 #define   PLL_REFDIV_MASK			GENMASK(6, 0)
37 #define   PLL_REFDIV_VAL			0x5
38 #define   PLL_FBDIV_OFFSET			16
39 #define   PLL_FBDIV_MASK			GENMASK(24, 16)
40 #define   PLL_FBDIV_VAL				0x60
41 #define   PLL_SEL_LPFR_MASK			GENMASK(29, 28)
42 #define   PLL_RDY				BIT(31)
43 #define UTMI_CAL_CTRL_REG			0x8
44 #define   IMPCAL_VTH_OFFSET			8
45 #define   IMPCAL_VTH_MASK			GENMASK(10, 8)
46 #define   IMPCAL_VTH_VAL			0x7
47 #define   IMPCAL_DONE				BIT(23)
48 #define   PLLCAL_DONE				BIT(31)
49 #define UTMI_TX_CH_CTRL_REG			0xC
50 #define   DRV_EN_LS_OFFSET			12
51 #define   DRV_EN_LS_MASK			GENMASK(15, 12)
52 #define   IMP_SEL_LS_OFFSET			16
53 #define   IMP_SEL_LS_MASK			GENMASK(19, 16)
54 #define   TX_AMP_OFFSET				20
55 #define   TX_AMP_MASK				GENMASK(22, 20)
56 #define   TX_AMP_VAL				0x4
57 #define UTMI_RX_CH_CTRL0_REG			0x14
58 #define   SQ_DET_EN				BIT(15)
59 #define   SQ_ANA_DTC_SEL			BIT(28)
60 #define UTMI_RX_CH_CTRL1_REG			0x18
61 #define   SQ_AMP_CAL_OFFSET			0
62 #define   SQ_AMP_CAL_MASK			GENMASK(2, 0)
63 #define   SQ_AMP_CAL_VAL			1
64 #define   SQ_AMP_CAL_EN				BIT(3)
65 #define UTMI_CTRL_STATUS0_REG			0x24
66 #define   SUSPENDM				BIT(22)
67 #define   TEST_SEL				BIT(25)
68 #define UTMI_CHGDTC_CTRL_REG			0x38
69 #define   VDAT_OFFSET				8
70 #define   VDAT_MASK				GENMASK(9, 8)
71 #define   VDAT_VAL				1
72 #define   VSRC_OFFSET				10
73 #define   VSRC_MASK				GENMASK(11, 10)
74 #define   VSRC_VAL				1
75 
76 #define PLL_LOCK_DELAY_US			10000
77 #define PLL_LOCK_TIMEOUT_US			1000000
78 
79 #define PORT_REGS(p)				((p)->priv->regs + (p)->id * 0x1000)
80 
81 /**
82  * struct mvebu_cp110_utmi - PHY driver data
83  *
84  * @regs: PHY registers
85  * @syscon: Regmap with system controller registers
86  * @dev: device driver handle
87  * @ops: phy ops
88  */
89 struct mvebu_cp110_utmi {
90 	void __iomem *regs;
91 	struct regmap *syscon;
92 	struct device *dev;
93 	const struct phy_ops *ops;
94 };
95 
96 /**
97  * struct mvebu_cp110_utmi_port - PHY port data
98  *
99  * @priv: PHY driver data
100  * @id: PHY port ID
101  * @dr_mode: PHY connection: USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL
102  */
103 struct mvebu_cp110_utmi_port {
104 	struct mvebu_cp110_utmi *priv;
105 	u32 id;
106 	enum usb_dr_mode dr_mode;
107 };
108 
mvebu_cp110_utmi_port_setup(struct mvebu_cp110_utmi_port * port)109 static void mvebu_cp110_utmi_port_setup(struct mvebu_cp110_utmi_port *port)
110 {
111 	u32 reg;
112 
113 	/*
114 	 * Setup PLL.
115 	 * The reference clock is the frequency of quartz resonator
116 	 * connected to pins REFCLK_XIN and REFCLK_XOUT of the SoC.
117 	 * Register init values are matching the 40MHz default clock.
118 	 * The crystal used for all platform boards is now 25MHz.
119 	 * See the functional specification for details.
120 	 */
121 	reg = readl(PORT_REGS(port) + UTMI_PLL_CTRL_REG);
122 	reg &= ~(PLL_REFDIV_MASK | PLL_FBDIV_MASK | PLL_SEL_LPFR_MASK);
123 	reg |= (PLL_REFDIV_VAL << PLL_REFDIV_OFFSET) |
124 	       (PLL_FBDIV_VAL << PLL_FBDIV_OFFSET);
125 	writel(reg, PORT_REGS(port) + UTMI_PLL_CTRL_REG);
126 
127 	/* Impedance Calibration Threshold Setting */
128 	reg = readl(PORT_REGS(port) + UTMI_CAL_CTRL_REG);
129 	reg &= ~IMPCAL_VTH_MASK;
130 	reg |= IMPCAL_VTH_VAL << IMPCAL_VTH_OFFSET;
131 	writel(reg, PORT_REGS(port) + UTMI_CAL_CTRL_REG);
132 
133 	/* Set LS TX driver strength coarse control */
134 	reg = readl(PORT_REGS(port) + UTMI_TX_CH_CTRL_REG);
135 	reg &= ~TX_AMP_MASK;
136 	reg |= TX_AMP_VAL << TX_AMP_OFFSET;
137 	writel(reg, PORT_REGS(port) + UTMI_TX_CH_CTRL_REG);
138 
139 	/* Disable SQ and enable analog squelch detect */
140 	reg = readl(PORT_REGS(port) + UTMI_RX_CH_CTRL0_REG);
141 	reg &= ~SQ_DET_EN;
142 	reg |= SQ_ANA_DTC_SEL;
143 	writel(reg, PORT_REGS(port) + UTMI_RX_CH_CTRL0_REG);
144 
145 	/*
146 	 * Set External squelch calibration number and
147 	 * enable the External squelch calibration
148 	 */
149 	reg = readl(PORT_REGS(port) + UTMI_RX_CH_CTRL1_REG);
150 	reg &= ~SQ_AMP_CAL_MASK;
151 	reg |= (SQ_AMP_CAL_VAL << SQ_AMP_CAL_OFFSET) | SQ_AMP_CAL_EN;
152 	writel(reg, PORT_REGS(port) + UTMI_RX_CH_CTRL1_REG);
153 
154 	/*
155 	 * Set Control VDAT Reference Voltage - 0.325V and
156 	 * Control VSRC Reference Voltage - 0.6V
157 	 */
158 	reg = readl(PORT_REGS(port) + UTMI_CHGDTC_CTRL_REG);
159 	reg &= ~(VDAT_MASK | VSRC_MASK);
160 	reg |= (VDAT_VAL << VDAT_OFFSET) | (VSRC_VAL << VSRC_OFFSET);
161 	writel(reg, PORT_REGS(port) + UTMI_CHGDTC_CTRL_REG);
162 }
163 
mvebu_cp110_utmi_phy_power_off(struct phy * phy)164 static int mvebu_cp110_utmi_phy_power_off(struct phy *phy)
165 {
166 	struct mvebu_cp110_utmi_port *port = phy_get_drvdata(phy);
167 	struct mvebu_cp110_utmi *utmi = port->priv;
168 	int i;
169 
170 	/* Power down UTMI PHY port */
171 	regmap_clear_bits(utmi->syscon, SYSCON_UTMI_CFG_REG(port->id),
172 			  UTMI_PHY_CFG_PU_MASK);
173 
174 	for (i = 0; i < UTMI_PHY_PORTS; i++) {
175 		int test = regmap_test_bits(utmi->syscon,
176 					    SYSCON_UTMI_CFG_REG(i),
177 					    UTMI_PHY_CFG_PU_MASK);
178 		/* skip PLL shutdown if there are active UTMI PHY ports */
179 		if (test != 0)
180 			return 0;
181 	}
182 
183 	/* PLL Power down if all UTMI PHYs are down */
184 	regmap_clear_bits(utmi->syscon, SYSCON_USB_CFG_REG, USB_CFG_PLL_MASK);
185 
186 	return 0;
187 }
188 
mvebu_cp110_utmi_phy_power_on(struct phy * phy)189 static int mvebu_cp110_utmi_phy_power_on(struct phy *phy)
190 {
191 	struct mvebu_cp110_utmi_port *port = phy_get_drvdata(phy);
192 	struct mvebu_cp110_utmi *utmi = port->priv;
193 	struct device *dev = &phy->dev;
194 	int ret;
195 	u32 reg;
196 
197 	/* It is necessary to power off UTMI before configuration */
198 	ret = mvebu_cp110_utmi_phy_power_off(phy);
199 	if (ret) {
200 		dev_err(dev, "UTMI power OFF before power ON failed\n");
201 		return ret;
202 	}
203 
204 	/*
205 	 * If UTMI port is connected to USB Device controller,
206 	 * configure the USB MUX prior to UTMI PHY initialization.
207 	 * The single USB device controller can be connected
208 	 * to UTMI0 or to UTMI1 PHY port, but not to both.
209 	 */
210 	if (port->dr_mode == USB_DR_MODE_PERIPHERAL) {
211 		regmap_update_bits(utmi->syscon, SYSCON_USB_CFG_REG,
212 				   USB_CFG_DEVICE_EN_MASK | USB_CFG_DEVICE_MUX_MASK,
213 				   USB_CFG_DEVICE_EN_MASK |
214 				   (port->id << USB_CFG_DEVICE_MUX_OFFSET));
215 	}
216 
217 	/* Set Test suspendm mode and enable Test UTMI select */
218 	reg = readl(PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
219 	reg |= SUSPENDM | TEST_SEL;
220 	writel(reg, PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
221 
222 	/* Wait for UTMI power down */
223 	mdelay(1);
224 
225 	/* PHY port setup first */
226 	mvebu_cp110_utmi_port_setup(port);
227 
228 	/* Power UP UTMI PHY */
229 	regmap_set_bits(utmi->syscon, SYSCON_UTMI_CFG_REG(port->id),
230 			UTMI_PHY_CFG_PU_MASK);
231 
232 	/* Disable Test UTMI select */
233 	reg = readl(PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
234 	reg &= ~TEST_SEL;
235 	writel(reg, PORT_REGS(port) + UTMI_CTRL_STATUS0_REG);
236 
237 	/* Wait for impedance calibration */
238 	ret = readl_poll_timeout(PORT_REGS(port) + UTMI_CAL_CTRL_REG, reg,
239 				 reg & IMPCAL_DONE,
240 				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
241 	if (ret) {
242 		dev_err(dev, "Failed to end UTMI impedance calibration\n");
243 		return ret;
244 	}
245 
246 	/* Wait for PLL calibration */
247 	ret = readl_poll_timeout(PORT_REGS(port) + UTMI_CAL_CTRL_REG, reg,
248 				 reg & PLLCAL_DONE,
249 				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
250 	if (ret) {
251 		dev_err(dev, "Failed to end UTMI PLL calibration\n");
252 		return ret;
253 	}
254 
255 	/* Wait for PLL ready */
256 	ret = readl_poll_timeout(PORT_REGS(port) + UTMI_PLL_CTRL_REG, reg,
257 				 reg & PLL_RDY,
258 				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
259 	if (ret) {
260 		dev_err(dev, "PLL is not ready\n");
261 		return ret;
262 	}
263 
264 	/* PLL Power up */
265 	regmap_set_bits(utmi->syscon, SYSCON_USB_CFG_REG, USB_CFG_PLL_MASK);
266 
267 	return 0;
268 }
269 
270 static const struct phy_ops mvebu_cp110_utmi_phy_ops = {
271 	.power_on = mvebu_cp110_utmi_phy_power_on,
272 	.power_off = mvebu_cp110_utmi_phy_power_off,
273 	.owner = THIS_MODULE,
274 };
275 
276 static const struct of_device_id mvebu_cp110_utmi_of_match[] = {
277 	{ .compatible = "marvell,cp110-utmi-phy" },
278 	{},
279 };
280 MODULE_DEVICE_TABLE(of, mvebu_cp110_utmi_of_match);
281 
mvebu_cp110_utmi_phy_probe(struct platform_device * pdev)282 static int mvebu_cp110_utmi_phy_probe(struct platform_device *pdev)
283 {
284 	struct device *dev = &pdev->dev;
285 	struct mvebu_cp110_utmi *utmi;
286 	struct phy_provider *provider;
287 	struct device_node *child;
288 	u32 usb_devices = 0;
289 
290 	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
291 	if (!utmi)
292 		return -ENOMEM;
293 
294 	utmi->dev = dev;
295 
296 	/* Get system controller region */
297 	utmi->syscon = syscon_regmap_lookup_by_phandle(dev->of_node,
298 						       "marvell,system-controller");
299 	if (IS_ERR(utmi->syscon)) {
300 		dev_err(dev, "Missing UTMI system controller\n");
301 		return PTR_ERR(utmi->syscon);
302 	}
303 
304 	/* Get UTMI memory region */
305 	utmi->regs = devm_platform_ioremap_resource(pdev, 0);
306 	if (IS_ERR(utmi->regs))
307 		return PTR_ERR(utmi->regs);
308 
309 	for_each_available_child_of_node(dev->of_node, child) {
310 		struct mvebu_cp110_utmi_port *port;
311 		struct phy *phy;
312 		int ret;
313 		u32 port_id;
314 
315 		ret = of_property_read_u32(child, "reg", &port_id);
316 		if ((ret < 0) || (port_id >= UTMI_PHY_PORTS)) {
317 			dev_err(dev,
318 				"invalid 'reg' property on child %pOF\n",
319 				child);
320 			continue;
321 		}
322 
323 		port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
324 		if (!port) {
325 			of_node_put(child);
326 			return -ENOMEM;
327 		}
328 
329 		port->dr_mode = of_usb_get_dr_mode_by_phy(child, -1);
330 		if ((port->dr_mode != USB_DR_MODE_HOST) &&
331 		    (port->dr_mode != USB_DR_MODE_PERIPHERAL)) {
332 			dev_err(&pdev->dev,
333 				"Missing dual role setting of the port%d, will use HOST mode\n",
334 				port_id);
335 			port->dr_mode = USB_DR_MODE_HOST;
336 		}
337 
338 		if (port->dr_mode == USB_DR_MODE_PERIPHERAL) {
339 			usb_devices++;
340 			if (usb_devices > 1) {
341 				dev_err(dev,
342 					"Single USB device allowed! Port%d will use HOST mode\n",
343 					port_id);
344 				port->dr_mode = USB_DR_MODE_HOST;
345 			}
346 		}
347 
348 		/* Retrieve PHY capabilities */
349 		utmi->ops = &mvebu_cp110_utmi_phy_ops;
350 
351 		/* Instantiate the PHY */
352 		phy = devm_phy_create(dev, child, utmi->ops);
353 		if (IS_ERR(phy)) {
354 			dev_err(dev, "Failed to create the UTMI PHY\n");
355 			of_node_put(child);
356 			return PTR_ERR(phy);
357 		}
358 
359 		port->priv = utmi;
360 		port->id = port_id;
361 		phy_set_drvdata(phy, port);
362 
363 		/* Ensure the PHY is powered off */
364 		mvebu_cp110_utmi_phy_power_off(phy);
365 	}
366 
367 	dev_set_drvdata(dev, utmi);
368 	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
369 
370 	return PTR_ERR_OR_ZERO(provider);
371 }
372 
373 static struct platform_driver mvebu_cp110_utmi_driver = {
374 	.probe	= mvebu_cp110_utmi_phy_probe,
375 	.driver	= {
376 		.name		= "mvebu-cp110-utmi-phy",
377 		.of_match_table	= mvebu_cp110_utmi_of_match,
378 	 },
379 };
380 module_platform_driver(mvebu_cp110_utmi_driver);
381 
382 MODULE_AUTHOR("Konstatin Porotchkin <kostap@marvell.com>");
383 MODULE_DESCRIPTION("Marvell Armada CP110 UTMI PHY driver");
384 MODULE_LICENSE("GPL v2");
385