1 /* SPDX-License-Identifier: GPL-2.0 */
2 /* Copyright(c) 2013 - 2018 Intel Corporation. */
3
4 #ifndef _IAVF_TXRX_H_
5 #define _IAVF_TXRX_H_
6
7 /* Interrupt Throttling and Rate Limiting Goodies */
8 #define IAVF_DEFAULT_IRQ_WORK 256
9
10 /* The datasheet for the X710 and XL710 indicate that the maximum value for
11 * the ITR is 8160usec which is then called out as 0xFF0 with a 2usec
12 * resolution. 8160 is 0x1FE0 when written out in hex. So instead of storing
13 * the register value which is divided by 2 lets use the actual values and
14 * avoid an excessive amount of translation.
15 */
16 #define IAVF_ITR_DYNAMIC 0x8000 /* use top bit as a flag */
17 #define IAVF_ITR_MASK 0x1FFE /* mask for ITR register value */
18 #define IAVF_ITR_100K 10 /* all values below must be even */
19 #define IAVF_ITR_50K 20
20 #define IAVF_ITR_20K 50
21 #define IAVF_ITR_18K 60
22 #define IAVF_ITR_8K 122
23 #define IAVF_MAX_ITR 8160 /* maximum value as per datasheet */
24 #define ITR_TO_REG(setting) ((setting) & ~IAVF_ITR_DYNAMIC)
25 #define ITR_REG_ALIGN(setting) __ALIGN_MASK(setting, ~IAVF_ITR_MASK)
26 #define ITR_IS_DYNAMIC(setting) (!!((setting) & IAVF_ITR_DYNAMIC))
27
28 #define IAVF_ITR_RX_DEF (IAVF_ITR_20K | IAVF_ITR_DYNAMIC)
29 #define IAVF_ITR_TX_DEF (IAVF_ITR_20K | IAVF_ITR_DYNAMIC)
30
31 /* 0x40 is the enable bit for interrupt rate limiting, and must be set if
32 * the value of the rate limit is non-zero
33 */
34 #define INTRL_ENA BIT(6)
35 #define IAVF_MAX_INTRL 0x3B /* reg uses 4 usec resolution */
36 #define INTRL_REG_TO_USEC(intrl) ((intrl & ~INTRL_ENA) << 2)
37 #define INTRL_USEC_TO_REG(set) ((set) ? ((set) >> 2) | INTRL_ENA : 0)
38 #define IAVF_INTRL_8K 125 /* 8000 ints/sec */
39 #define IAVF_INTRL_62K 16 /* 62500 ints/sec */
40 #define IAVF_INTRL_83K 12 /* 83333 ints/sec */
41
42 #define IAVF_QUEUE_END_OF_LIST 0x7FF
43
44 /* this enum matches hardware bits and is meant to be used by DYN_CTLN
45 * registers and QINT registers or more generally anywhere in the manual
46 * mentioning ITR_INDX, ITR_NONE cannot be used as an index 'n' into any
47 * register but instead is a special value meaning "don't update" ITR0/1/2.
48 */
49 enum iavf_dyn_idx_t {
50 IAVF_IDX_ITR0 = 0,
51 IAVF_IDX_ITR1 = 1,
52 IAVF_IDX_ITR2 = 2,
53 IAVF_ITR_NONE = 3 /* ITR_NONE must not be used as an index */
54 };
55
56 /* these are indexes into ITRN registers */
57 #define IAVF_RX_ITR IAVF_IDX_ITR0
58 #define IAVF_TX_ITR IAVF_IDX_ITR1
59 #define IAVF_PE_ITR IAVF_IDX_ITR2
60
61 /* Supported RSS offloads */
62 #define IAVF_DEFAULT_RSS_HENA ( \
63 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV4_UDP) | \
64 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV4_SCTP) | \
65 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV4_TCP) | \
66 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV4_OTHER) | \
67 BIT_ULL(IAVF_FILTER_PCTYPE_FRAG_IPV4) | \
68 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV6_UDP) | \
69 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV6_TCP) | \
70 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV6_SCTP) | \
71 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV6_OTHER) | \
72 BIT_ULL(IAVF_FILTER_PCTYPE_FRAG_IPV6) | \
73 BIT_ULL(IAVF_FILTER_PCTYPE_L2_PAYLOAD))
74
75 #define IAVF_DEFAULT_RSS_HENA_EXPANDED (IAVF_DEFAULT_RSS_HENA | \
76 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV4_TCP_SYN_NO_ACK) | \
77 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_UNICAST_IPV4_UDP) | \
78 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_MULTICAST_IPV4_UDP) | \
79 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_IPV6_TCP_SYN_NO_ACK) | \
80 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_UNICAST_IPV6_UDP) | \
81 BIT_ULL(IAVF_FILTER_PCTYPE_NONF_MULTICAST_IPV6_UDP))
82
83 /* Supported Rx Buffer Sizes (a multiple of 128) */
84 #define IAVF_RXBUFFER_256 256
85 #define IAVF_RXBUFFER_1536 1536 /* 128B aligned standard Ethernet frame */
86 #define IAVF_RXBUFFER_2048 2048
87 #define IAVF_RXBUFFER_3072 3072 /* Used for large frames w/ padding */
88 #define IAVF_MAX_RXBUFFER 9728 /* largest size for single descriptor */
89
90 /* NOTE: netdev_alloc_skb reserves up to 64 bytes, NET_IP_ALIGN means we
91 * reserve 2 more, and skb_shared_info adds an additional 384 bytes more,
92 * this adds up to 512 bytes of extra data meaning the smallest allocation
93 * we could have is 1K.
94 * i.e. RXBUFFER_256 --> 960 byte skb (size-1024 slab)
95 * i.e. RXBUFFER_512 --> 1216 byte skb (size-2048 slab)
96 */
97 #define IAVF_RX_HDR_SIZE IAVF_RXBUFFER_256
98 #define IAVF_PACKET_HDR_PAD (ETH_HLEN + ETH_FCS_LEN + (VLAN_HLEN * 2))
99 #define iavf_rx_desc iavf_32byte_rx_desc
100
101 #define IAVF_RX_DMA_ATTR \
102 (DMA_ATTR_SKIP_CPU_SYNC | DMA_ATTR_WEAK_ORDERING)
103
104 /* Attempt to maximize the headroom available for incoming frames. We
105 * use a 2K buffer for receives and need 1536/1534 to store the data for
106 * the frame. This leaves us with 512 bytes of room. From that we need
107 * to deduct the space needed for the shared info and the padding needed
108 * to IP align the frame.
109 *
110 * Note: For cache line sizes 256 or larger this value is going to end
111 * up negative. In these cases we should fall back to the legacy
112 * receive path.
113 */
114 #if (PAGE_SIZE < 8192)
115 #define IAVF_2K_TOO_SMALL_WITH_PADDING \
116 ((NET_SKB_PAD + IAVF_RXBUFFER_1536) > SKB_WITH_OVERHEAD(IAVF_RXBUFFER_2048))
117
iavf_compute_pad(int rx_buf_len)118 static inline int iavf_compute_pad(int rx_buf_len)
119 {
120 int page_size, pad_size;
121
122 page_size = ALIGN(rx_buf_len, PAGE_SIZE / 2);
123 pad_size = SKB_WITH_OVERHEAD(page_size) - rx_buf_len;
124
125 return pad_size;
126 }
127
iavf_skb_pad(void)128 static inline int iavf_skb_pad(void)
129 {
130 int rx_buf_len;
131
132 /* If a 2K buffer cannot handle a standard Ethernet frame then
133 * optimize padding for a 3K buffer instead of a 1.5K buffer.
134 *
135 * For a 3K buffer we need to add enough padding to allow for
136 * tailroom due to NET_IP_ALIGN possibly shifting us out of
137 * cache-line alignment.
138 */
139 if (IAVF_2K_TOO_SMALL_WITH_PADDING)
140 rx_buf_len = IAVF_RXBUFFER_3072 + SKB_DATA_ALIGN(NET_IP_ALIGN);
141 else
142 rx_buf_len = IAVF_RXBUFFER_1536;
143
144 /* if needed make room for NET_IP_ALIGN */
145 rx_buf_len -= NET_IP_ALIGN;
146
147 return iavf_compute_pad(rx_buf_len);
148 }
149
150 #define IAVF_SKB_PAD iavf_skb_pad()
151 #else
152 #define IAVF_2K_TOO_SMALL_WITH_PADDING false
153 #define IAVF_SKB_PAD (NET_SKB_PAD + NET_IP_ALIGN)
154 #endif
155
156 /**
157 * iavf_test_staterr - tests bits in Rx descriptor status and error fields
158 * @rx_desc: pointer to receive descriptor (in le64 format)
159 * @stat_err_bits: value to mask
160 *
161 * This function does some fast chicanery in order to return the
162 * value of the mask which is really only used for boolean tests.
163 * The status_error_len doesn't need to be shifted because it begins
164 * at offset zero.
165 */
iavf_test_staterr(union iavf_rx_desc * rx_desc,const u64 stat_err_bits)166 static inline bool iavf_test_staterr(union iavf_rx_desc *rx_desc,
167 const u64 stat_err_bits)
168 {
169 return !!(rx_desc->wb.qword1.status_error_len &
170 cpu_to_le64(stat_err_bits));
171 }
172
173 /* How many Rx Buffers do we bundle into one write to the hardware ? */
174 #define IAVF_RX_INCREMENT(r, i) \
175 do { \
176 (i)++; \
177 if ((i) == (r)->count) \
178 i = 0; \
179 r->next_to_clean = i; \
180 } while (0)
181
182 #define IAVF_RX_NEXT_DESC(r, i, n) \
183 do { \
184 (i)++; \
185 if ((i) == (r)->count) \
186 i = 0; \
187 (n) = IAVF_RX_DESC((r), (i)); \
188 } while (0)
189
190 #define IAVF_RX_NEXT_DESC_PREFETCH(r, i, n) \
191 do { \
192 IAVF_RX_NEXT_DESC((r), (i), (n)); \
193 prefetch((n)); \
194 } while (0)
195
196 #define IAVF_MAX_BUFFER_TXD 8
197 #define IAVF_MIN_TX_LEN 17
198
199 /* The size limit for a transmit buffer in a descriptor is (16K - 1).
200 * In order to align with the read requests we will align the value to
201 * the nearest 4K which represents our maximum read request size.
202 */
203 #define IAVF_MAX_READ_REQ_SIZE 4096
204 #define IAVF_MAX_DATA_PER_TXD (16 * 1024 - 1)
205 #define IAVF_MAX_DATA_PER_TXD_ALIGNED \
206 (IAVF_MAX_DATA_PER_TXD & ~(IAVF_MAX_READ_REQ_SIZE - 1))
207
208 /**
209 * iavf_txd_use_count - estimate the number of descriptors needed for Tx
210 * @size: transmit request size in bytes
211 *
212 * Due to hardware alignment restrictions (4K alignment), we need to
213 * assume that we can have no more than 12K of data per descriptor, even
214 * though each descriptor can take up to 16K - 1 bytes of aligned memory.
215 * Thus, we need to divide by 12K. But division is slow! Instead,
216 * we decompose the operation into shifts and one relatively cheap
217 * multiply operation.
218 *
219 * To divide by 12K, we first divide by 4K, then divide by 3:
220 * To divide by 4K, shift right by 12 bits
221 * To divide by 3, multiply by 85, then divide by 256
222 * (Divide by 256 is done by shifting right by 8 bits)
223 * Finally, we add one to round up. Because 256 isn't an exact multiple of
224 * 3, we'll underestimate near each multiple of 12K. This is actually more
225 * accurate as we have 4K - 1 of wiggle room that we can fit into the last
226 * segment. For our purposes this is accurate out to 1M which is orders of
227 * magnitude greater than our largest possible GSO size.
228 *
229 * This would then be implemented as:
230 * return (((size >> 12) * 85) >> 8) + 1;
231 *
232 * Since multiplication and division are commutative, we can reorder
233 * operations into:
234 * return ((size * 85) >> 20) + 1;
235 */
iavf_txd_use_count(unsigned int size)236 static inline unsigned int iavf_txd_use_count(unsigned int size)
237 {
238 return ((size * 85) >> 20) + 1;
239 }
240
241 /* Tx Descriptors needed, worst case */
242 #define DESC_NEEDED (MAX_SKB_FRAGS + 6)
243 #define IAVF_MIN_DESC_PENDING 4
244
245 #define IAVF_TX_FLAGS_HW_VLAN BIT(1)
246 #define IAVF_TX_FLAGS_SW_VLAN BIT(2)
247 #define IAVF_TX_FLAGS_TSO BIT(3)
248 #define IAVF_TX_FLAGS_IPV4 BIT(4)
249 #define IAVF_TX_FLAGS_IPV6 BIT(5)
250 #define IAVF_TX_FLAGS_FCCRC BIT(6)
251 #define IAVF_TX_FLAGS_FSO BIT(7)
252 #define IAVF_TX_FLAGS_FD_SB BIT(9)
253 #define IAVF_TX_FLAGS_VXLAN_TUNNEL BIT(10)
254 #define IAVF_TX_FLAGS_HW_OUTER_SINGLE_VLAN BIT(11)
255 #define IAVF_TX_FLAGS_VLAN_MASK 0xffff0000
256 #define IAVF_TX_FLAGS_VLAN_PRIO_MASK 0xe0000000
257 #define IAVF_TX_FLAGS_VLAN_PRIO_SHIFT 29
258 #define IAVF_TX_FLAGS_VLAN_SHIFT 16
259
260 struct iavf_tx_buffer {
261 struct iavf_tx_desc *next_to_watch;
262 union {
263 struct sk_buff *skb;
264 void *raw_buf;
265 };
266 unsigned int bytecount;
267 unsigned short gso_segs;
268
269 DEFINE_DMA_UNMAP_ADDR(dma);
270 DEFINE_DMA_UNMAP_LEN(len);
271 u32 tx_flags;
272 };
273
274 struct iavf_rx_buffer {
275 dma_addr_t dma;
276 struct page *page;
277 #if (BITS_PER_LONG > 32) || (PAGE_SIZE >= 65536)
278 __u32 page_offset;
279 #else
280 __u16 page_offset;
281 #endif
282 __u16 pagecnt_bias;
283 };
284
285 struct iavf_queue_stats {
286 u64 packets;
287 u64 bytes;
288 };
289
290 struct iavf_tx_queue_stats {
291 u64 restart_queue;
292 u64 tx_busy;
293 u64 tx_done_old;
294 u64 tx_linearize;
295 u64 tx_force_wb;
296 int prev_pkt_ctr;
297 u64 tx_lost_interrupt;
298 };
299
300 struct iavf_rx_queue_stats {
301 u64 non_eop_descs;
302 u64 alloc_page_failed;
303 u64 alloc_buff_failed;
304 u64 page_reuse_count;
305 u64 realloc_count;
306 };
307
308 enum iavf_ring_state_t {
309 __IAVF_TX_FDIR_INIT_DONE,
310 __IAVF_TX_XPS_INIT_DONE,
311 __IAVF_RING_STATE_NBITS /* must be last */
312 };
313
314 /* some useful defines for virtchannel interface, which
315 * is the only remaining user of header split
316 */
317 #define IAVF_RX_DTYPE_NO_SPLIT 0
318 #define IAVF_RX_DTYPE_HEADER_SPLIT 1
319 #define IAVF_RX_DTYPE_SPLIT_ALWAYS 2
320 #define IAVF_RX_SPLIT_L2 0x1
321 #define IAVF_RX_SPLIT_IP 0x2
322 #define IAVF_RX_SPLIT_TCP_UDP 0x4
323 #define IAVF_RX_SPLIT_SCTP 0x8
324
325 /* struct that defines a descriptor ring, associated with a VSI */
326 struct iavf_ring {
327 struct iavf_ring *next; /* pointer to next ring in q_vector */
328 void *desc; /* Descriptor ring memory */
329 struct device *dev; /* Used for DMA mapping */
330 struct net_device *netdev; /* netdev ring maps to */
331 union {
332 struct iavf_tx_buffer *tx_bi;
333 struct iavf_rx_buffer *rx_bi;
334 };
335 DECLARE_BITMAP(state, __IAVF_RING_STATE_NBITS);
336 u16 queue_index; /* Queue number of ring */
337 u8 dcb_tc; /* Traffic class of ring */
338 u8 __iomem *tail;
339
340 /* high bit set means dynamic, use accessors routines to read/write.
341 * hardware only supports 2us resolution for the ITR registers.
342 * these values always store the USER setting, and must be converted
343 * before programming to a register.
344 */
345 u16 itr_setting;
346
347 u16 count; /* Number of descriptors */
348 u16 reg_idx; /* HW register index of the ring */
349 u16 rx_buf_len;
350
351 /* used in interrupt processing */
352 u16 next_to_use;
353 u16 next_to_clean;
354
355 u8 atr_sample_rate;
356 u8 atr_count;
357
358 bool ring_active; /* is ring online or not */
359 bool arm_wb; /* do something to arm write back */
360 u8 packet_stride;
361
362 u16 flags;
363 #define IAVF_TXR_FLAGS_WB_ON_ITR BIT(0)
364 #define IAVF_RXR_FLAGS_BUILD_SKB_ENABLED BIT(1)
365 #define IAVF_TXRX_FLAGS_VLAN_TAG_LOC_L2TAG1 BIT(3)
366 #define IAVF_TXR_FLAGS_VLAN_TAG_LOC_L2TAG2 BIT(4)
367 #define IAVF_RXR_FLAGS_VLAN_TAG_LOC_L2TAG2_2 BIT(5)
368
369 /* stats structs */
370 struct iavf_queue_stats stats;
371 struct u64_stats_sync syncp;
372 union {
373 struct iavf_tx_queue_stats tx_stats;
374 struct iavf_rx_queue_stats rx_stats;
375 };
376
377 unsigned int size; /* length of descriptor ring in bytes */
378 dma_addr_t dma; /* physical address of ring */
379
380 struct iavf_vsi *vsi; /* Backreference to associated VSI */
381 struct iavf_q_vector *q_vector; /* Backreference to associated vector */
382
383 struct rcu_head rcu; /* to avoid race on free */
384 u16 next_to_alloc;
385 struct sk_buff *skb; /* When iavf_clean_rx_ring_irq() must
386 * return before it sees the EOP for
387 * the current packet, we save that skb
388 * here and resume receiving this
389 * packet the next time
390 * iavf_clean_rx_ring_irq() is called
391 * for this ring.
392 */
393 } ____cacheline_internodealigned_in_smp;
394
ring_uses_build_skb(struct iavf_ring * ring)395 static inline bool ring_uses_build_skb(struct iavf_ring *ring)
396 {
397 return !!(ring->flags & IAVF_RXR_FLAGS_BUILD_SKB_ENABLED);
398 }
399
set_ring_build_skb_enabled(struct iavf_ring * ring)400 static inline void set_ring_build_skb_enabled(struct iavf_ring *ring)
401 {
402 ring->flags |= IAVF_RXR_FLAGS_BUILD_SKB_ENABLED;
403 }
404
clear_ring_build_skb_enabled(struct iavf_ring * ring)405 static inline void clear_ring_build_skb_enabled(struct iavf_ring *ring)
406 {
407 ring->flags &= ~IAVF_RXR_FLAGS_BUILD_SKB_ENABLED;
408 }
409
410 #define IAVF_ITR_ADAPTIVE_MIN_INC 0x0002
411 #define IAVF_ITR_ADAPTIVE_MIN_USECS 0x0002
412 #define IAVF_ITR_ADAPTIVE_MAX_USECS 0x007e
413 #define IAVF_ITR_ADAPTIVE_LATENCY 0x8000
414 #define IAVF_ITR_ADAPTIVE_BULK 0x0000
415 #define ITR_IS_BULK(x) (!((x) & IAVF_ITR_ADAPTIVE_LATENCY))
416
417 struct iavf_ring_container {
418 struct iavf_ring *ring; /* pointer to linked list of ring(s) */
419 unsigned long next_update; /* jiffies value of next update */
420 unsigned int total_bytes; /* total bytes processed this int */
421 unsigned int total_packets; /* total packets processed this int */
422 u16 count;
423 u16 target_itr; /* target ITR setting for ring(s) */
424 u16 current_itr; /* current ITR setting for ring(s) */
425 };
426
427 /* iterator for handling rings in ring container */
428 #define iavf_for_each_ring(pos, head) \
429 for (pos = (head).ring; pos != NULL; pos = pos->next)
430
iavf_rx_pg_order(struct iavf_ring * ring)431 static inline unsigned int iavf_rx_pg_order(struct iavf_ring *ring)
432 {
433 #if (PAGE_SIZE < 8192)
434 if (ring->rx_buf_len > (PAGE_SIZE / 2))
435 return 1;
436 #endif
437 return 0;
438 }
439
440 #define iavf_rx_pg_size(_ring) (PAGE_SIZE << iavf_rx_pg_order(_ring))
441
442 bool iavf_alloc_rx_buffers(struct iavf_ring *rxr, u16 cleaned_count);
443 netdev_tx_t iavf_xmit_frame(struct sk_buff *skb, struct net_device *netdev);
444 int iavf_setup_tx_descriptors(struct iavf_ring *tx_ring);
445 int iavf_setup_rx_descriptors(struct iavf_ring *rx_ring);
446 void iavf_free_tx_resources(struct iavf_ring *tx_ring);
447 void iavf_free_rx_resources(struct iavf_ring *rx_ring);
448 int iavf_napi_poll(struct napi_struct *napi, int budget);
449 void iavf_detect_recover_hung(struct iavf_vsi *vsi);
450 int __iavf_maybe_stop_tx(struct iavf_ring *tx_ring, int size);
451 bool __iavf_chk_linearize(struct sk_buff *skb);
452
453 /**
454 * iavf_xmit_descriptor_count - calculate number of Tx descriptors needed
455 * @skb: send buffer
456 *
457 * Returns number of data descriptors needed for this skb. Returns 0 to indicate
458 * there is not enough descriptors available in this ring since we need at least
459 * one descriptor.
460 **/
iavf_xmit_descriptor_count(struct sk_buff * skb)461 static inline int iavf_xmit_descriptor_count(struct sk_buff *skb)
462 {
463 const skb_frag_t *frag = &skb_shinfo(skb)->frags[0];
464 unsigned int nr_frags = skb_shinfo(skb)->nr_frags;
465 int count = 0, size = skb_headlen(skb);
466
467 for (;;) {
468 count += iavf_txd_use_count(size);
469
470 if (!nr_frags--)
471 break;
472
473 size = skb_frag_size(frag++);
474 }
475
476 return count;
477 }
478
479 /**
480 * iavf_maybe_stop_tx - 1st level check for Tx stop conditions
481 * @tx_ring: the ring to be checked
482 * @size: the size buffer we want to assure is available
483 *
484 * Returns 0 if stop is not needed
485 **/
iavf_maybe_stop_tx(struct iavf_ring * tx_ring,int size)486 static inline int iavf_maybe_stop_tx(struct iavf_ring *tx_ring, int size)
487 {
488 if (likely(IAVF_DESC_UNUSED(tx_ring) >= size))
489 return 0;
490 return __iavf_maybe_stop_tx(tx_ring, size);
491 }
492
493 /**
494 * iavf_chk_linearize - Check if there are more than 8 fragments per packet
495 * @skb: send buffer
496 * @count: number of buffers used
497 *
498 * Note: Our HW can't scatter-gather more than 8 fragments to build
499 * a packet on the wire and so we need to figure out the cases where we
500 * need to linearize the skb.
501 **/
iavf_chk_linearize(struct sk_buff * skb,int count)502 static inline bool iavf_chk_linearize(struct sk_buff *skb, int count)
503 {
504 /* Both TSO and single send will work if count is less than 8 */
505 if (likely(count < IAVF_MAX_BUFFER_TXD))
506 return false;
507
508 if (skb_is_gso(skb))
509 return __iavf_chk_linearize(skb);
510
511 /* we can support up to 8 data buffers for a single send */
512 return count != IAVF_MAX_BUFFER_TXD;
513 }
514 /**
515 * txring_txq - helper to convert from a ring to a queue
516 * @ring: Tx ring to find the netdev equivalent of
517 **/
txring_txq(const struct iavf_ring * ring)518 static inline struct netdev_queue *txring_txq(const struct iavf_ring *ring)
519 {
520 return netdev_get_tx_queue(ring->netdev, ring->queue_index);
521 }
522 #endif /* _IAVF_TXRX_H_ */
523