xref: /openbmc/u-boot/include/configs/lx2160ardb.h (revision c507d306)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright 2018 NXP
4  */
5 
6 #ifndef __LX2_RDB_H
7 #define __LX2_RDB_H
8 
9 #include "lx2160a_common.h"
10 
11 /* Qixis */
12 #define QIXIS_XMAP_MASK			0x07
13 #define QIXIS_XMAP_SHIFT		5
14 #define QIXIS_RST_CTL_RESET_EN		0x30
15 #define QIXIS_LBMAP_DFLTBANK		0x00
16 #define QIXIS_LBMAP_ALTBANK		0x20
17 #define QIXIS_LBMAP_QSPI		0x00
18 #define QIXIS_RCW_SRC_QSPI		0xff
19 #define QIXIS_RST_CTL_RESET		0x31
20 #define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
21 #define QIXIS_RCFG_CTL_RECONFIG_START	0x21
22 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
23 #define QIXIS_LBMAP_MASK		0x0f
24 #define QIXIS_LBMAP_SD
25 #define QIXIS_RCW_SRC_SD           0x08
26 #define NON_EXTENDED_DUTCFG
27 
28 /* VID */
29 
30 #define I2C_MUX_CH_VOL_MONITOR		0xA
31 /* Voltage monitor on channel 2*/
32 #define I2C_VOL_MONITOR_ADDR		0x63
33 #define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
34 #define I2C_VOL_MONITOR_BUS_V_OVF	0x1
35 #define I2C_VOL_MONITOR_BUS_V_SHIFT	3
36 #define CONFIG_VID_FLS_ENV		"lx2160ardb_vdd_mv"
37 #define CONFIG_VID
38 
39 /* The lowest and highest voltage allowed*/
40 #define VDD_MV_MIN			775
41 #define VDD_MV_MAX			855
42 
43 /* PM Bus commands code for LTC3882*/
44 #define PMBUS_CMD_PAGE                  0x0
45 #define PMBUS_CMD_READ_VOUT             0x8B
46 #define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
47 #define PMBUS_CMD_VOUT_COMMAND          0x21
48 #define PWM_CHANNEL0                    0x0
49 
50 #define CONFIG_VOL_MONITOR_LTC3882_SET
51 #define CONFIG_VOL_MONITOR_LTC3882_READ
52 
53 /* RTC */
54 #define CONFIG_SYS_RTC_BUS_NUM		4
55 
56 /* MAC/PHY configuration */
57 #if defined(CONFIG_FSL_MC_ENET)
58 #define CONFIG_MII
59 #define CONFIG_ETHPRIME		"DPMAC1@xgmii"
60 
61 #define AQR107_PHY_ADDR1	0x04
62 #define AQR107_PHY_ADDR2	0x05
63 
64 #define CORTINA_NO_FW_UPLOAD
65 #define CORTINA_PHY_ADDR1	0x0
66 #define INPHI_PHY_ADDR1		0x0
67 
68 #define RGMII_PHY_ADDR1		0x01
69 #define RGMII_PHY_ADDR2		0x02
70 
71 #endif
72 
73 /* EMC2305 */
74 #define I2C_MUX_CH_EMC2305		0x09
75 #define I2C_EMC2305_ADDR		0x4D
76 #define I2C_EMC2305_CMD		0x40
77 #define I2C_EMC2305_PWM		0x80
78 
79 /* EEPROM */
80 #define CONFIG_ID_EEPROM
81 #define CONFIG_SYS_I2C_EEPROM_NXID
82 #define CONFIG_SYS_EEPROM_BUS_NUM	           0
83 #define CONFIG_SYS_I2C_EEPROM_ADDR	           0x57
84 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	    1
85 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     3
86 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
87 
88 /* Initial environment variables */
89 #define CONFIG_EXTRA_ENV_SETTINGS		\
90 	EXTRA_ENV_SETTINGS			\
91 	"lx2160ardb_vdd_mv=800\0"		\
92 	"BOARD=lx2160ardb\0"			\
93 	"xspi_bootcmd=echo Trying load from flexspi..;"		\
94 		"sf probe 0:0 && sf read $load_addr "		\
95 		"$kernel_start $kernel_size ; env exists secureboot &&"	\
96 		"sf read $kernelheader_addr_r $kernelheader_start "	\
97 		"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
98 		" bootm $load_addr#$BOARD\0"			\
99 	"sd_bootcmd=echo Trying load from sd card..;"		\
100 		"mmcinfo; mmc read $load_addr "			\
101 		"$kernel_addr_sd $kernel_size_sd ;"		\
102 		"env exists secureboot && mmc read $kernelheader_addr_r "\
103 		"$kernelhdr_addr_sd $kernelhdr_size_sd "	\
104 		" && esbc_validate ${kernelheader_addr_r};"	\
105 		"bootm $load_addr#$BOARD\0"
106 
107 #include <asm/fsl_secure_boot.h>
108 
109 #endif /* __LX2_RDB_H */
110