1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (C) 2012 Simon Budig, <simon.budig@kernelconcepts.de>
4 * Daniel Wagener <daniel.wagener@kernelconcepts.de> (M09 firmware support)
5 * Lothar Waßmann <LW@KARO-electronics.de> (DT support)
6 * Dario Binacchi <dario.binacchi@amarulasolutions.com> (regmap support)
7 */
8
9 /*
10 * This is a driver for the EDT "Polytouch" family of touch controllers
11 * based on the FocalTech FT5x06 line of chips.
12 *
13 * Development of this driver has been sponsored by Glyn:
14 * http://www.glyn.com/Products/Displays
15 */
16
17 #include <linux/debugfs.h>
18 #include <linux/delay.h>
19 #include <linux/gpio/consumer.h>
20 #include <linux/i2c.h>
21 #include <linux/interrupt.h>
22 #include <linux/input.h>
23 #include <linux/input/mt.h>
24 #include <linux/input/touchscreen.h>
25 #include <linux/irq.h>
26 #include <linux/kernel.h>
27 #include <linux/module.h>
28 #include <linux/property.h>
29 #include <linux/ratelimit.h>
30 #include <linux/regmap.h>
31 #include <linux/regulator/consumer.h>
32 #include <linux/slab.h>
33 #include <linux/uaccess.h>
34
35 #include <asm/unaligned.h>
36
37 #define WORK_REGISTER_THRESHOLD 0x00
38 #define WORK_REGISTER_REPORT_RATE 0x08
39 #define WORK_REGISTER_GAIN 0x30
40 #define WORK_REGISTER_OFFSET 0x31
41 #define WORK_REGISTER_NUM_X 0x33
42 #define WORK_REGISTER_NUM_Y 0x34
43
44 #define PMOD_REGISTER_ACTIVE 0x00
45 #define PMOD_REGISTER_HIBERNATE 0x03
46
47 #define M09_REGISTER_THRESHOLD 0x80
48 #define M09_REGISTER_GAIN 0x92
49 #define M09_REGISTER_OFFSET 0x93
50 #define M09_REGISTER_NUM_X 0x94
51 #define M09_REGISTER_NUM_Y 0x95
52
53 #define M12_REGISTER_REPORT_RATE 0x88
54
55 #define EV_REGISTER_THRESHOLD 0x40
56 #define EV_REGISTER_GAIN 0x41
57 #define EV_REGISTER_OFFSET_Y 0x45
58 #define EV_REGISTER_OFFSET_X 0x46
59
60 #define NO_REGISTER 0xff
61
62 #define WORK_REGISTER_OPMODE 0x3c
63 #define FACTORY_REGISTER_OPMODE 0x01
64 #define PMOD_REGISTER_OPMODE 0xa5
65
66 #define TOUCH_EVENT_DOWN 0x00
67 #define TOUCH_EVENT_UP 0x01
68 #define TOUCH_EVENT_ON 0x02
69 #define TOUCH_EVENT_RESERVED 0x03
70
71 #define EDT_NAME_LEN 23
72 #define EDT_SWITCH_MODE_RETRIES 10
73 #define EDT_SWITCH_MODE_DELAY 5 /* msec */
74 #define EDT_RAW_DATA_RETRIES 100
75 #define EDT_RAW_DATA_DELAY 1000 /* usec */
76
77 #define EDT_DEFAULT_NUM_X 1024
78 #define EDT_DEFAULT_NUM_Y 1024
79
80 #define M06_REG_CMD(factory) ((factory) ? 0xf3 : 0xfc)
81 #define M06_REG_ADDR(factory, addr) ((factory) ? (addr) & 0x7f : (addr) & 0x3f)
82
83 enum edt_pmode {
84 EDT_PMODE_NOT_SUPPORTED,
85 EDT_PMODE_HIBERNATE,
86 EDT_PMODE_POWEROFF,
87 };
88
89 enum edt_ver {
90 EDT_M06,
91 EDT_M09,
92 EDT_M12,
93 EV_FT,
94 GENERIC_FT,
95 };
96
97 struct edt_reg_addr {
98 int reg_threshold;
99 int reg_report_rate;
100 int reg_gain;
101 int reg_offset;
102 int reg_offset_x;
103 int reg_offset_y;
104 int reg_num_x;
105 int reg_num_y;
106 };
107
108 struct edt_ft5x06_ts_data {
109 struct i2c_client *client;
110 struct input_dev *input;
111 struct touchscreen_properties prop;
112 u16 num_x;
113 u16 num_y;
114 struct regulator *vcc;
115 struct regulator *iovcc;
116
117 struct gpio_desc *reset_gpio;
118 struct gpio_desc *wake_gpio;
119
120 struct regmap *regmap;
121
122 #if defined(CONFIG_DEBUG_FS)
123 struct dentry *debug_dir;
124 u8 *raw_buffer;
125 size_t raw_bufsize;
126 #endif
127
128 struct mutex mutex;
129 bool factory_mode;
130 enum edt_pmode suspend_mode;
131 int threshold;
132 int gain;
133 int offset;
134 int offset_x;
135 int offset_y;
136 int report_rate;
137 int max_support_points;
138 int point_len;
139 u8 tdata_cmd;
140 int tdata_len;
141 int tdata_offset;
142
143 char name[EDT_NAME_LEN];
144 char fw_version[EDT_NAME_LEN];
145
146 struct edt_reg_addr reg_addr;
147 enum edt_ver version;
148 unsigned int crc_errors;
149 unsigned int header_errors;
150 };
151
152 struct edt_i2c_chip_data {
153 int max_support_points;
154 };
155
156 static const struct regmap_config edt_ft5x06_i2c_regmap_config = {
157 .reg_bits = 8,
158 .val_bits = 8,
159 };
160
edt_ft5x06_ts_check_crc(struct edt_ft5x06_ts_data * tsdata,u8 * buf,int buflen)161 static bool edt_ft5x06_ts_check_crc(struct edt_ft5x06_ts_data *tsdata,
162 u8 *buf, int buflen)
163 {
164 int i;
165 u8 crc = 0;
166
167 for (i = 0; i < buflen - 1; i++)
168 crc ^= buf[i];
169
170 if (crc != buf[buflen - 1]) {
171 tsdata->crc_errors++;
172 dev_err_ratelimited(&tsdata->client->dev,
173 "crc error: 0x%02x expected, got 0x%02x\n",
174 crc, buf[buflen - 1]);
175 return false;
176 }
177
178 return true;
179 }
180
edt_M06_i2c_read(void * context,const void * reg_buf,size_t reg_size,void * val_buf,size_t val_size)181 static int edt_M06_i2c_read(void *context, const void *reg_buf, size_t reg_size,
182 void *val_buf, size_t val_size)
183 {
184 struct device *dev = context;
185 struct i2c_client *i2c = to_i2c_client(dev);
186 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(i2c);
187 struct i2c_msg xfer[2];
188 bool reg_read = false;
189 u8 addr;
190 u8 wlen;
191 u8 wbuf[4], rbuf[3];
192 int ret;
193
194 addr = *((u8 *)reg_buf);
195 wbuf[0] = addr;
196 switch (addr) {
197 case 0xf5:
198 wlen = 3;
199 wbuf[0] = 0xf5;
200 wbuf[1] = 0xe;
201 wbuf[2] = *((u8 *)val_buf);
202 break;
203 case 0xf9:
204 wlen = 1;
205 break;
206 default:
207 wlen = 2;
208 reg_read = true;
209 wbuf[0] = M06_REG_CMD(tsdata->factory_mode);
210 wbuf[1] = M06_REG_ADDR(tsdata->factory_mode, addr);
211 wbuf[1] |= tsdata->factory_mode ? 0x80 : 0x40;
212 }
213
214 xfer[0].addr = i2c->addr;
215 xfer[0].flags = 0;
216 xfer[0].len = wlen;
217 xfer[0].buf = wbuf;
218
219 xfer[1].addr = i2c->addr;
220 xfer[1].flags = I2C_M_RD;
221 xfer[1].len = reg_read ? 2 : val_size;
222 xfer[1].buf = reg_read ? rbuf : val_buf;
223
224 ret = i2c_transfer(i2c->adapter, xfer, 2);
225 if (ret != 2) {
226 if (ret < 0)
227 return ret;
228
229 return -EIO;
230 }
231
232 if (addr == 0xf9) {
233 u8 *buf = (u8 *)val_buf;
234
235 if (buf[0] != 0xaa || buf[1] != 0xaa ||
236 buf[2] != val_size) {
237 tsdata->header_errors++;
238 dev_err_ratelimited(dev,
239 "Unexpected header: %02x%02x%02x\n",
240 buf[0], buf[1], buf[2]);
241 return -EIO;
242 }
243
244 if (!edt_ft5x06_ts_check_crc(tsdata, val_buf, val_size))
245 return -EIO;
246 } else if (reg_read) {
247 wbuf[2] = rbuf[0];
248 wbuf[3] = rbuf[1];
249 if (!edt_ft5x06_ts_check_crc(tsdata, wbuf, 4))
250 return -EIO;
251
252 *((u8 *)val_buf) = rbuf[0];
253 }
254
255 return 0;
256 }
257
edt_M06_i2c_write(void * context,const void * data,size_t count)258 static int edt_M06_i2c_write(void *context, const void *data, size_t count)
259 {
260 struct device *dev = context;
261 struct i2c_client *i2c = to_i2c_client(dev);
262 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(i2c);
263 u8 addr, val;
264 u8 wbuf[4];
265 struct i2c_msg xfer;
266 int ret;
267
268 addr = *((u8 *)data);
269 val = *((u8 *)data + 1);
270
271 wbuf[0] = M06_REG_CMD(tsdata->factory_mode);
272 wbuf[1] = M06_REG_ADDR(tsdata->factory_mode, addr);
273 wbuf[2] = val;
274 wbuf[3] = wbuf[0] ^ wbuf[1] ^ wbuf[2];
275
276 xfer.addr = i2c->addr;
277 xfer.flags = 0;
278 xfer.len = 4;
279 xfer.buf = wbuf;
280
281 ret = i2c_transfer(i2c->adapter, &xfer, 1);
282 if (ret != 1) {
283 if (ret < 0)
284 return ret;
285
286 return -EIO;
287 }
288
289 return 0;
290 }
291
292 static const struct regmap_config edt_M06_i2c_regmap_config = {
293 .reg_bits = 8,
294 .val_bits = 8,
295 .read = edt_M06_i2c_read,
296 .write = edt_M06_i2c_write,
297 };
298
edt_ft5x06_ts_isr(int irq,void * dev_id)299 static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
300 {
301 struct edt_ft5x06_ts_data *tsdata = dev_id;
302 struct device *dev = &tsdata->client->dev;
303 u8 rdbuf[63];
304 int i, type, x, y, id;
305 int error;
306
307 memset(rdbuf, 0, sizeof(rdbuf));
308 error = regmap_bulk_read(tsdata->regmap, tsdata->tdata_cmd, rdbuf,
309 tsdata->tdata_len);
310 if (error) {
311 dev_err_ratelimited(dev, "Unable to fetch data, error: %d\n",
312 error);
313 goto out;
314 }
315
316 for (i = 0; i < tsdata->max_support_points; i++) {
317 u8 *buf = &rdbuf[i * tsdata->point_len + tsdata->tdata_offset];
318
319 type = buf[0] >> 6;
320 /* ignore Reserved events */
321 if (type == TOUCH_EVENT_RESERVED)
322 continue;
323
324 /* M06 sometimes sends bogus coordinates in TOUCH_DOWN */
325 if (tsdata->version == EDT_M06 && type == TOUCH_EVENT_DOWN)
326 continue;
327
328 x = get_unaligned_be16(buf) & 0x0fff;
329 y = get_unaligned_be16(buf + 2) & 0x0fff;
330 /* The FT5x26 send the y coordinate first */
331 if (tsdata->version == EV_FT)
332 swap(x, y);
333
334 id = (buf[2] >> 4) & 0x0f;
335
336 input_mt_slot(tsdata->input, id);
337 if (input_mt_report_slot_state(tsdata->input, MT_TOOL_FINGER,
338 type != TOUCH_EVENT_UP))
339 touchscreen_report_pos(tsdata->input, &tsdata->prop,
340 x, y, true);
341 }
342
343 input_mt_report_pointer_emulation(tsdata->input, true);
344 input_sync(tsdata->input);
345
346 out:
347 return IRQ_HANDLED;
348 }
349
350 struct edt_ft5x06_attribute {
351 struct device_attribute dattr;
352 size_t field_offset;
353 u8 limit_low;
354 u8 limit_high;
355 u8 addr_m06;
356 u8 addr_m09;
357 u8 addr_ev;
358 };
359
360 #define EDT_ATTR(_field, _mode, _addr_m06, _addr_m09, _addr_ev, \
361 _limit_low, _limit_high) \
362 struct edt_ft5x06_attribute edt_ft5x06_attr_##_field = { \
363 .dattr = __ATTR(_field, _mode, \
364 edt_ft5x06_setting_show, \
365 edt_ft5x06_setting_store), \
366 .field_offset = offsetof(struct edt_ft5x06_ts_data, _field), \
367 .addr_m06 = _addr_m06, \
368 .addr_m09 = _addr_m09, \
369 .addr_ev = _addr_ev, \
370 .limit_low = _limit_low, \
371 .limit_high = _limit_high, \
372 }
373
edt_ft5x06_setting_show(struct device * dev,struct device_attribute * dattr,char * buf)374 static ssize_t edt_ft5x06_setting_show(struct device *dev,
375 struct device_attribute *dattr,
376 char *buf)
377 {
378 struct i2c_client *client = to_i2c_client(dev);
379 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
380 struct edt_ft5x06_attribute *attr =
381 container_of(dattr, struct edt_ft5x06_attribute, dattr);
382 u8 *field = (u8 *)tsdata + attr->field_offset;
383 unsigned int val;
384 size_t count = 0;
385 int error = 0;
386 u8 addr;
387
388 mutex_lock(&tsdata->mutex);
389
390 if (tsdata->factory_mode) {
391 error = -EIO;
392 goto out;
393 }
394
395 switch (tsdata->version) {
396 case EDT_M06:
397 addr = attr->addr_m06;
398 break;
399
400 case EDT_M09:
401 case EDT_M12:
402 case GENERIC_FT:
403 addr = attr->addr_m09;
404 break;
405
406 case EV_FT:
407 addr = attr->addr_ev;
408 break;
409
410 default:
411 error = -ENODEV;
412 goto out;
413 }
414
415 if (addr != NO_REGISTER) {
416 error = regmap_read(tsdata->regmap, addr, &val);
417 if (error) {
418 dev_err(&tsdata->client->dev,
419 "Failed to fetch attribute %s, error %d\n",
420 dattr->attr.name, error);
421 goto out;
422 }
423 } else {
424 val = *field;
425 }
426
427 if (val != *field) {
428 dev_warn(&tsdata->client->dev,
429 "%s: read (%d) and stored value (%d) differ\n",
430 dattr->attr.name, val, *field);
431 *field = val;
432 }
433
434 count = scnprintf(buf, PAGE_SIZE, "%d\n", val);
435 out:
436 mutex_unlock(&tsdata->mutex);
437 return error ?: count;
438 }
439
edt_ft5x06_setting_store(struct device * dev,struct device_attribute * dattr,const char * buf,size_t count)440 static ssize_t edt_ft5x06_setting_store(struct device *dev,
441 struct device_attribute *dattr,
442 const char *buf, size_t count)
443 {
444 struct i2c_client *client = to_i2c_client(dev);
445 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
446 struct edt_ft5x06_attribute *attr =
447 container_of(dattr, struct edt_ft5x06_attribute, dattr);
448 u8 *field = (u8 *)tsdata + attr->field_offset;
449 unsigned int val;
450 int error;
451 u8 addr;
452
453 mutex_lock(&tsdata->mutex);
454
455 if (tsdata->factory_mode) {
456 error = -EIO;
457 goto out;
458 }
459
460 error = kstrtouint(buf, 0, &val);
461 if (error)
462 goto out;
463
464 if (val < attr->limit_low || val > attr->limit_high) {
465 error = -ERANGE;
466 goto out;
467 }
468
469 switch (tsdata->version) {
470 case EDT_M06:
471 addr = attr->addr_m06;
472 break;
473
474 case EDT_M09:
475 case EDT_M12:
476 case GENERIC_FT:
477 addr = attr->addr_m09;
478 break;
479
480 case EV_FT:
481 addr = attr->addr_ev;
482 break;
483
484 default:
485 error = -ENODEV;
486 goto out;
487 }
488
489 if (addr != NO_REGISTER) {
490 error = regmap_write(tsdata->regmap, addr, val);
491 if (error) {
492 dev_err(&tsdata->client->dev,
493 "Failed to update attribute %s, error: %d\n",
494 dattr->attr.name, error);
495 goto out;
496 }
497 }
498 *field = val;
499
500 out:
501 mutex_unlock(&tsdata->mutex);
502 return error ?: count;
503 }
504
505 /* m06, m09: range 0-31, m12: range 0-5 */
506 static EDT_ATTR(gain, S_IWUSR | S_IRUGO, WORK_REGISTER_GAIN,
507 M09_REGISTER_GAIN, EV_REGISTER_GAIN, 0, 31);
508 /* m06, m09: range 0-31, m12: range 0-16 */
509 static EDT_ATTR(offset, S_IWUSR | S_IRUGO, WORK_REGISTER_OFFSET,
510 M09_REGISTER_OFFSET, NO_REGISTER, 0, 31);
511 /* m06, m09, m12: no supported, ev_ft: range 0-80 */
512 static EDT_ATTR(offset_x, S_IWUSR | S_IRUGO, NO_REGISTER, NO_REGISTER,
513 EV_REGISTER_OFFSET_X, 0, 80);
514 /* m06, m09, m12: no supported, ev_ft: range 0-80 */
515 static EDT_ATTR(offset_y, S_IWUSR | S_IRUGO, NO_REGISTER, NO_REGISTER,
516 EV_REGISTER_OFFSET_Y, 0, 80);
517 /* m06: range 20 to 80, m09: range 0 to 30, m12: range 1 to 255... */
518 static EDT_ATTR(threshold, S_IWUSR | S_IRUGO, WORK_REGISTER_THRESHOLD,
519 M09_REGISTER_THRESHOLD, EV_REGISTER_THRESHOLD, 0, 255);
520 /* m06: range 3 to 14, m12: range 1 to 255 */
521 static EDT_ATTR(report_rate, S_IWUSR | S_IRUGO, WORK_REGISTER_REPORT_RATE,
522 M12_REGISTER_REPORT_RATE, NO_REGISTER, 0, 255);
523
model_show(struct device * dev,struct device_attribute * attr,char * buf)524 static ssize_t model_show(struct device *dev, struct device_attribute *attr,
525 char *buf)
526 {
527 struct i2c_client *client = to_i2c_client(dev);
528 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
529
530 return sysfs_emit(buf, "%s\n", tsdata->name);
531 }
532
533 static DEVICE_ATTR_RO(model);
534
fw_version_show(struct device * dev,struct device_attribute * attr,char * buf)535 static ssize_t fw_version_show(struct device *dev,
536 struct device_attribute *attr, char *buf)
537 {
538 struct i2c_client *client = to_i2c_client(dev);
539 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
540
541 return sysfs_emit(buf, "%s\n", tsdata->fw_version);
542 }
543
544 static DEVICE_ATTR_RO(fw_version);
545
546 /* m06 only */
header_errors_show(struct device * dev,struct device_attribute * attr,char * buf)547 static ssize_t header_errors_show(struct device *dev,
548 struct device_attribute *attr, char *buf)
549 {
550 struct i2c_client *client = to_i2c_client(dev);
551 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
552
553 return sysfs_emit(buf, "%d\n", tsdata->header_errors);
554 }
555
556 static DEVICE_ATTR_RO(header_errors);
557
558 /* m06 only */
crc_errors_show(struct device * dev,struct device_attribute * attr,char * buf)559 static ssize_t crc_errors_show(struct device *dev,
560 struct device_attribute *attr, char *buf)
561 {
562 struct i2c_client *client = to_i2c_client(dev);
563 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
564
565 return sysfs_emit(buf, "%d\n", tsdata->crc_errors);
566 }
567
568 static DEVICE_ATTR_RO(crc_errors);
569
570 static struct attribute *edt_ft5x06_attrs[] = {
571 &edt_ft5x06_attr_gain.dattr.attr,
572 &edt_ft5x06_attr_offset.dattr.attr,
573 &edt_ft5x06_attr_offset_x.dattr.attr,
574 &edt_ft5x06_attr_offset_y.dattr.attr,
575 &edt_ft5x06_attr_threshold.dattr.attr,
576 &edt_ft5x06_attr_report_rate.dattr.attr,
577 &dev_attr_model.attr,
578 &dev_attr_fw_version.attr,
579 &dev_attr_header_errors.attr,
580 &dev_attr_crc_errors.attr,
581 NULL
582 };
583
584 static const struct attribute_group edt_ft5x06_attr_group = {
585 .attrs = edt_ft5x06_attrs,
586 };
587
edt_ft5x06_restore_reg_parameters(struct edt_ft5x06_ts_data * tsdata)588 static void edt_ft5x06_restore_reg_parameters(struct edt_ft5x06_ts_data *tsdata)
589 {
590 struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
591 struct regmap *regmap = tsdata->regmap;
592
593 regmap_write(regmap, reg_addr->reg_threshold, tsdata->threshold);
594 regmap_write(regmap, reg_addr->reg_gain, tsdata->gain);
595 if (reg_addr->reg_offset != NO_REGISTER)
596 regmap_write(regmap, reg_addr->reg_offset, tsdata->offset);
597 if (reg_addr->reg_offset_x != NO_REGISTER)
598 regmap_write(regmap, reg_addr->reg_offset_x, tsdata->offset_x);
599 if (reg_addr->reg_offset_y != NO_REGISTER)
600 regmap_write(regmap, reg_addr->reg_offset_y, tsdata->offset_y);
601 if (reg_addr->reg_report_rate != NO_REGISTER)
602 regmap_write(regmap, reg_addr->reg_report_rate,
603 tsdata->report_rate);
604 }
605
606 #ifdef CONFIG_DEBUG_FS
edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data * tsdata)607 static int edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data *tsdata)
608 {
609 struct i2c_client *client = tsdata->client;
610 int retries = EDT_SWITCH_MODE_RETRIES;
611 unsigned int val;
612 int error;
613
614 if (tsdata->version != EDT_M06) {
615 dev_err(&client->dev,
616 "No factory mode support for non-M06 devices\n");
617 return -EINVAL;
618 }
619
620 disable_irq(client->irq);
621
622 if (!tsdata->raw_buffer) {
623 tsdata->raw_bufsize = tsdata->num_x * tsdata->num_y *
624 sizeof(u16);
625 tsdata->raw_buffer = kzalloc(tsdata->raw_bufsize, GFP_KERNEL);
626 if (!tsdata->raw_buffer) {
627 error = -ENOMEM;
628 goto err_out;
629 }
630 }
631
632 /* mode register is 0x3c when in the work mode */
633 error = regmap_write(tsdata->regmap, WORK_REGISTER_OPMODE, 0x03);
634 if (error) {
635 dev_err(&client->dev,
636 "failed to switch to factory mode, error %d\n", error);
637 goto err_out;
638 }
639
640 tsdata->factory_mode = true;
641 do {
642 mdelay(EDT_SWITCH_MODE_DELAY);
643 /* mode register is 0x01 when in factory mode */
644 error = regmap_read(tsdata->regmap, FACTORY_REGISTER_OPMODE,
645 &val);
646 if (!error && val == 0x03)
647 break;
648 } while (--retries > 0);
649
650 if (retries == 0) {
651 dev_err(&client->dev, "not in factory mode after %dms.\n",
652 EDT_SWITCH_MODE_RETRIES * EDT_SWITCH_MODE_DELAY);
653 error = -EIO;
654 goto err_out;
655 }
656
657 return 0;
658
659 err_out:
660 kfree(tsdata->raw_buffer);
661 tsdata->raw_buffer = NULL;
662 tsdata->factory_mode = false;
663 enable_irq(client->irq);
664
665 return error;
666 }
667
edt_ft5x06_work_mode(struct edt_ft5x06_ts_data * tsdata)668 static int edt_ft5x06_work_mode(struct edt_ft5x06_ts_data *tsdata)
669 {
670 struct i2c_client *client = tsdata->client;
671 int retries = EDT_SWITCH_MODE_RETRIES;
672 unsigned int val;
673 int error;
674
675 /* mode register is 0x01 when in the factory mode */
676 error = regmap_write(tsdata->regmap, FACTORY_REGISTER_OPMODE, 0x1);
677 if (error) {
678 dev_err(&client->dev,
679 "failed to switch to work mode, error: %d\n", error);
680 return error;
681 }
682
683 tsdata->factory_mode = false;
684
685 do {
686 mdelay(EDT_SWITCH_MODE_DELAY);
687 /* mode register is 0x01 when in factory mode */
688 error = regmap_read(tsdata->regmap, WORK_REGISTER_OPMODE, &val);
689 if (!error && val == 0x01)
690 break;
691 } while (--retries > 0);
692
693 if (retries == 0) {
694 dev_err(&client->dev, "not in work mode after %dms.\n",
695 EDT_SWITCH_MODE_RETRIES * EDT_SWITCH_MODE_DELAY);
696 tsdata->factory_mode = true;
697 return -EIO;
698 }
699
700 kfree(tsdata->raw_buffer);
701 tsdata->raw_buffer = NULL;
702
703 edt_ft5x06_restore_reg_parameters(tsdata);
704 enable_irq(client->irq);
705
706 return 0;
707 }
708
edt_ft5x06_debugfs_mode_get(void * data,u64 * mode)709 static int edt_ft5x06_debugfs_mode_get(void *data, u64 *mode)
710 {
711 struct edt_ft5x06_ts_data *tsdata = data;
712
713 *mode = tsdata->factory_mode;
714
715 return 0;
716 };
717
edt_ft5x06_debugfs_mode_set(void * data,u64 mode)718 static int edt_ft5x06_debugfs_mode_set(void *data, u64 mode)
719 {
720 struct edt_ft5x06_ts_data *tsdata = data;
721 int retval = 0;
722
723 if (mode > 1)
724 return -ERANGE;
725
726 mutex_lock(&tsdata->mutex);
727
728 if (mode != tsdata->factory_mode) {
729 retval = mode ? edt_ft5x06_factory_mode(tsdata) :
730 edt_ft5x06_work_mode(tsdata);
731 }
732
733 mutex_unlock(&tsdata->mutex);
734
735 return retval;
736 };
737
738 DEFINE_SIMPLE_ATTRIBUTE(debugfs_mode_fops, edt_ft5x06_debugfs_mode_get,
739 edt_ft5x06_debugfs_mode_set, "%llu\n");
740
edt_ft5x06_debugfs_raw_data_read(struct file * file,char __user * buf,size_t count,loff_t * off)741 static ssize_t edt_ft5x06_debugfs_raw_data_read(struct file *file,
742 char __user *buf, size_t count,
743 loff_t *off)
744 {
745 struct edt_ft5x06_ts_data *tsdata = file->private_data;
746 struct i2c_client *client = tsdata->client;
747 int retries = EDT_RAW_DATA_RETRIES;
748 unsigned int val;
749 int i, error;
750 size_t read = 0;
751 int colbytes;
752 u8 *rdbuf;
753
754 if (*off < 0 || *off >= tsdata->raw_bufsize)
755 return 0;
756
757 mutex_lock(&tsdata->mutex);
758
759 if (!tsdata->factory_mode || !tsdata->raw_buffer) {
760 error = -EIO;
761 goto out;
762 }
763
764 error = regmap_write(tsdata->regmap, 0x08, 0x01);
765 if (error) {
766 dev_err(&client->dev,
767 "failed to write 0x08 register, error %d\n", error);
768 goto out;
769 }
770
771 do {
772 usleep_range(EDT_RAW_DATA_DELAY, EDT_RAW_DATA_DELAY + 100);
773 error = regmap_read(tsdata->regmap, 0x08, &val);
774 if (error) {
775 dev_err(&client->dev,
776 "failed to read 0x08 register, error %d\n",
777 error);
778 goto out;
779 }
780
781 if (val == 1)
782 break;
783 } while (--retries > 0);
784
785 if (retries == 0) {
786 dev_err(&client->dev,
787 "timed out waiting for register to settle\n");
788 error = -ETIMEDOUT;
789 goto out;
790 }
791
792 rdbuf = tsdata->raw_buffer;
793 colbytes = tsdata->num_y * sizeof(u16);
794
795 for (i = 0; i < tsdata->num_x; i++) {
796 rdbuf[0] = i; /* column index */
797 error = regmap_bulk_read(tsdata->regmap, 0xf5, rdbuf, colbytes);
798 if (error)
799 goto out;
800
801 rdbuf += colbytes;
802 }
803
804 read = min_t(size_t, count, tsdata->raw_bufsize - *off);
805 if (copy_to_user(buf, tsdata->raw_buffer + *off, read)) {
806 error = -EFAULT;
807 goto out;
808 }
809
810 *off += read;
811 out:
812 mutex_unlock(&tsdata->mutex);
813 return error ?: read;
814 };
815
816 static const struct file_operations debugfs_raw_data_fops = {
817 .open = simple_open,
818 .read = edt_ft5x06_debugfs_raw_data_read,
819 };
820
edt_ft5x06_ts_prepare_debugfs(struct edt_ft5x06_ts_data * tsdata,const char * debugfs_name)821 static void edt_ft5x06_ts_prepare_debugfs(struct edt_ft5x06_ts_data *tsdata,
822 const char *debugfs_name)
823 {
824 tsdata->debug_dir = debugfs_create_dir(debugfs_name, NULL);
825
826 debugfs_create_u16("num_x", S_IRUSR, tsdata->debug_dir, &tsdata->num_x);
827 debugfs_create_u16("num_y", S_IRUSR, tsdata->debug_dir, &tsdata->num_y);
828
829 debugfs_create_file("mode", S_IRUSR | S_IWUSR,
830 tsdata->debug_dir, tsdata, &debugfs_mode_fops);
831 debugfs_create_file("raw_data", S_IRUSR,
832 tsdata->debug_dir, tsdata, &debugfs_raw_data_fops);
833 }
834
edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data * tsdata)835 static void edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
836 {
837 debugfs_remove_recursive(tsdata->debug_dir);
838 kfree(tsdata->raw_buffer);
839 }
840
841 #else
842
edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data * tsdata)843 static int edt_ft5x06_factory_mode(struct edt_ft5x06_ts_data *tsdata)
844 {
845 return -ENOSYS;
846 }
847
edt_ft5x06_ts_prepare_debugfs(struct edt_ft5x06_ts_data * tsdata,const char * debugfs_name)848 static void edt_ft5x06_ts_prepare_debugfs(struct edt_ft5x06_ts_data *tsdata,
849 const char *debugfs_name)
850 {
851 }
852
edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data * tsdata)853 static void edt_ft5x06_ts_teardown_debugfs(struct edt_ft5x06_ts_data *tsdata)
854 {
855 }
856
857 #endif /* CONFIG_DEBUGFS */
858
edt_ft5x06_ts_identify(struct i2c_client * client,struct edt_ft5x06_ts_data * tsdata)859 static int edt_ft5x06_ts_identify(struct i2c_client *client,
860 struct edt_ft5x06_ts_data *tsdata)
861 {
862 u8 rdbuf[EDT_NAME_LEN];
863 char *p;
864 int error;
865 char *model_name = tsdata->name;
866 char *fw_version = tsdata->fw_version;
867
868 /* see what we find if we assume it is a M06 *
869 * if we get less than EDT_NAME_LEN, we don't want
870 * to have garbage in there
871 */
872 memset(rdbuf, 0, sizeof(rdbuf));
873 error = regmap_bulk_read(tsdata->regmap, 0xBB, rdbuf, EDT_NAME_LEN - 1);
874 if (error)
875 return error;
876
877 /* Probe content for something consistent.
878 * M06 starts with a response byte, M12 gives the data directly.
879 * M09/Generic does not provide model number information.
880 */
881 if (!strncasecmp(rdbuf + 1, "EP0", 3)) {
882 tsdata->version = EDT_M06;
883
884 /* remove last '$' end marker */
885 rdbuf[EDT_NAME_LEN - 1] = '\0';
886 if (rdbuf[EDT_NAME_LEN - 2] == '$')
887 rdbuf[EDT_NAME_LEN - 2] = '\0';
888
889 /* look for Model/Version separator */
890 p = strchr(rdbuf, '*');
891 if (p)
892 *p++ = '\0';
893 strscpy(model_name, rdbuf + 1, EDT_NAME_LEN);
894 strscpy(fw_version, p ? p : "", EDT_NAME_LEN);
895
896 regmap_exit(tsdata->regmap);
897 tsdata->regmap = regmap_init_i2c(client,
898 &edt_M06_i2c_regmap_config);
899 if (IS_ERR(tsdata->regmap)) {
900 dev_err(&client->dev, "regmap allocation failed\n");
901 return PTR_ERR(tsdata->regmap);
902 }
903 } else if (!strncasecmp(rdbuf, "EP0", 3)) {
904 tsdata->version = EDT_M12;
905
906 /* remove last '$' end marker */
907 rdbuf[EDT_NAME_LEN - 2] = '\0';
908 if (rdbuf[EDT_NAME_LEN - 3] == '$')
909 rdbuf[EDT_NAME_LEN - 3] = '\0';
910
911 /* look for Model/Version separator */
912 p = strchr(rdbuf, '*');
913 if (p)
914 *p++ = '\0';
915 strscpy(model_name, rdbuf, EDT_NAME_LEN);
916 strscpy(fw_version, p ? p : "", EDT_NAME_LEN);
917 } else {
918 /* If it is not an EDT M06/M12 touchscreen, then the model
919 * detection is a bit hairy. The different ft5x06
920 * firmwares around don't reliably implement the
921 * identification registers. Well, we'll take a shot.
922 *
923 * The main difference between generic focaltec based
924 * touches and EDT M09 is that we know how to retrieve
925 * the max coordinates for the latter.
926 */
927 tsdata->version = GENERIC_FT;
928
929 error = regmap_bulk_read(tsdata->regmap, 0xA6, rdbuf, 2);
930 if (error)
931 return error;
932
933 strscpy(fw_version, rdbuf, 2);
934
935 error = regmap_bulk_read(tsdata->regmap, 0xA8, rdbuf, 1);
936 if (error)
937 return error;
938
939 /* This "model identification" is not exact. Unfortunately
940 * not all firmwares for the ft5x06 put useful values in
941 * the identification registers.
942 */
943 switch (rdbuf[0]) {
944 case 0x11: /* EDT EP0110M09 */
945 case 0x35: /* EDT EP0350M09 */
946 case 0x43: /* EDT EP0430M09 */
947 case 0x50: /* EDT EP0500M09 */
948 case 0x57: /* EDT EP0570M09 */
949 case 0x70: /* EDT EP0700M09 */
950 tsdata->version = EDT_M09;
951 snprintf(model_name, EDT_NAME_LEN, "EP0%i%i0M09",
952 rdbuf[0] >> 4, rdbuf[0] & 0x0F);
953 break;
954 case 0xa1: /* EDT EP1010ML00 */
955 tsdata->version = EDT_M09;
956 snprintf(model_name, EDT_NAME_LEN, "EP%i%i0ML00",
957 rdbuf[0] >> 4, rdbuf[0] & 0x0F);
958 break;
959 case 0x5a: /* Solomon Goldentek Display */
960 snprintf(model_name, EDT_NAME_LEN, "GKTW50SCED1R0");
961 break;
962 case 0x59: /* Evervision Display with FT5xx6 TS */
963 tsdata->version = EV_FT;
964 error = regmap_bulk_read(tsdata->regmap, 0x53, rdbuf, 1);
965 if (error)
966 return error;
967 strscpy(fw_version, rdbuf, 1);
968 snprintf(model_name, EDT_NAME_LEN,
969 "EVERVISION-FT5726NEi");
970 break;
971 default:
972 snprintf(model_name, EDT_NAME_LEN,
973 "generic ft5x06 (%02x)",
974 rdbuf[0]);
975 break;
976 }
977 }
978
979 return 0;
980 }
981
edt_ft5x06_ts_get_defaults(struct device * dev,struct edt_ft5x06_ts_data * tsdata)982 static void edt_ft5x06_ts_get_defaults(struct device *dev,
983 struct edt_ft5x06_ts_data *tsdata)
984 {
985 struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
986 struct regmap *regmap = tsdata->regmap;
987 u32 val;
988 int error;
989
990 error = device_property_read_u32(dev, "threshold", &val);
991 if (!error) {
992 regmap_write(regmap, reg_addr->reg_threshold, val);
993 tsdata->threshold = val;
994 }
995
996 error = device_property_read_u32(dev, "gain", &val);
997 if (!error) {
998 regmap_write(regmap, reg_addr->reg_gain, val);
999 tsdata->gain = val;
1000 }
1001
1002 error = device_property_read_u32(dev, "offset", &val);
1003 if (!error) {
1004 if (reg_addr->reg_offset != NO_REGISTER)
1005 regmap_write(regmap, reg_addr->reg_offset, val);
1006 tsdata->offset = val;
1007 }
1008
1009 error = device_property_read_u32(dev, "offset-x", &val);
1010 if (!error) {
1011 if (reg_addr->reg_offset_x != NO_REGISTER)
1012 regmap_write(regmap, reg_addr->reg_offset_x, val);
1013 tsdata->offset_x = val;
1014 }
1015
1016 error = device_property_read_u32(dev, "offset-y", &val);
1017 if (!error) {
1018 if (reg_addr->reg_offset_y != NO_REGISTER)
1019 regmap_write(regmap, reg_addr->reg_offset_y, val);
1020 tsdata->offset_y = val;
1021 }
1022 }
1023
edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data * tsdata)1024 static void edt_ft5x06_ts_get_parameters(struct edt_ft5x06_ts_data *tsdata)
1025 {
1026 struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
1027 struct regmap *regmap = tsdata->regmap;
1028 unsigned int val;
1029
1030 regmap_read(regmap, reg_addr->reg_threshold, &tsdata->threshold);
1031 regmap_read(regmap, reg_addr->reg_gain, &tsdata->gain);
1032 if (reg_addr->reg_offset != NO_REGISTER)
1033 regmap_read(regmap, reg_addr->reg_offset, &tsdata->offset);
1034 if (reg_addr->reg_offset_x != NO_REGISTER)
1035 regmap_read(regmap, reg_addr->reg_offset_x, &tsdata->offset_x);
1036 if (reg_addr->reg_offset_y != NO_REGISTER)
1037 regmap_read(regmap, reg_addr->reg_offset_y, &tsdata->offset_y);
1038 if (reg_addr->reg_report_rate != NO_REGISTER)
1039 regmap_read(regmap, reg_addr->reg_report_rate,
1040 &tsdata->report_rate);
1041 tsdata->num_x = EDT_DEFAULT_NUM_X;
1042 if (reg_addr->reg_num_x != NO_REGISTER) {
1043 if (!regmap_read(regmap, reg_addr->reg_num_x, &val))
1044 tsdata->num_x = val;
1045 }
1046 tsdata->num_y = EDT_DEFAULT_NUM_Y;
1047 if (reg_addr->reg_num_y != NO_REGISTER) {
1048 if (!regmap_read(regmap, reg_addr->reg_num_y, &val))
1049 tsdata->num_y = val;
1050 }
1051 }
1052
edt_ft5x06_ts_set_tdata_parameters(struct edt_ft5x06_ts_data * tsdata)1053 static void edt_ft5x06_ts_set_tdata_parameters(struct edt_ft5x06_ts_data *tsdata)
1054 {
1055 int crclen;
1056
1057 if (tsdata->version == EDT_M06) {
1058 tsdata->tdata_cmd = 0xf9;
1059 tsdata->tdata_offset = 5;
1060 tsdata->point_len = 4;
1061 crclen = 1;
1062 } else {
1063 tsdata->tdata_cmd = 0x0;
1064 tsdata->tdata_offset = 3;
1065 tsdata->point_len = 6;
1066 crclen = 0;
1067 }
1068
1069 tsdata->tdata_len = tsdata->point_len * tsdata->max_support_points +
1070 tsdata->tdata_offset + crclen;
1071 }
1072
edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data * tsdata)1073 static void edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
1074 {
1075 struct edt_reg_addr *reg_addr = &tsdata->reg_addr;
1076
1077 switch (tsdata->version) {
1078 case EDT_M06:
1079 reg_addr->reg_threshold = WORK_REGISTER_THRESHOLD;
1080 reg_addr->reg_report_rate = WORK_REGISTER_REPORT_RATE;
1081 reg_addr->reg_gain = WORK_REGISTER_GAIN;
1082 reg_addr->reg_offset = WORK_REGISTER_OFFSET;
1083 reg_addr->reg_offset_x = NO_REGISTER;
1084 reg_addr->reg_offset_y = NO_REGISTER;
1085 reg_addr->reg_num_x = WORK_REGISTER_NUM_X;
1086 reg_addr->reg_num_y = WORK_REGISTER_NUM_Y;
1087 break;
1088
1089 case EDT_M09:
1090 case EDT_M12:
1091 reg_addr->reg_threshold = M09_REGISTER_THRESHOLD;
1092 reg_addr->reg_report_rate = tsdata->version == EDT_M12 ?
1093 M12_REGISTER_REPORT_RATE : NO_REGISTER;
1094 reg_addr->reg_gain = M09_REGISTER_GAIN;
1095 reg_addr->reg_offset = M09_REGISTER_OFFSET;
1096 reg_addr->reg_offset_x = NO_REGISTER;
1097 reg_addr->reg_offset_y = NO_REGISTER;
1098 reg_addr->reg_num_x = M09_REGISTER_NUM_X;
1099 reg_addr->reg_num_y = M09_REGISTER_NUM_Y;
1100 break;
1101
1102 case EV_FT:
1103 reg_addr->reg_threshold = EV_REGISTER_THRESHOLD;
1104 reg_addr->reg_report_rate = NO_REGISTER;
1105 reg_addr->reg_gain = EV_REGISTER_GAIN;
1106 reg_addr->reg_offset = NO_REGISTER;
1107 reg_addr->reg_offset_x = EV_REGISTER_OFFSET_X;
1108 reg_addr->reg_offset_y = EV_REGISTER_OFFSET_Y;
1109 reg_addr->reg_num_x = NO_REGISTER;
1110 reg_addr->reg_num_y = NO_REGISTER;
1111 break;
1112
1113 case GENERIC_FT:
1114 /* this is a guesswork */
1115 reg_addr->reg_threshold = M09_REGISTER_THRESHOLD;
1116 reg_addr->reg_report_rate = NO_REGISTER;
1117 reg_addr->reg_gain = M09_REGISTER_GAIN;
1118 reg_addr->reg_offset = M09_REGISTER_OFFSET;
1119 reg_addr->reg_offset_x = NO_REGISTER;
1120 reg_addr->reg_offset_y = NO_REGISTER;
1121 reg_addr->reg_num_x = NO_REGISTER;
1122 reg_addr->reg_num_y = NO_REGISTER;
1123 break;
1124 }
1125 }
1126
edt_ft5x06_exit_regmap(void * arg)1127 static void edt_ft5x06_exit_regmap(void *arg)
1128 {
1129 struct edt_ft5x06_ts_data *data = arg;
1130
1131 if (!IS_ERR_OR_NULL(data->regmap))
1132 regmap_exit(data->regmap);
1133 }
1134
edt_ft5x06_disable_regulators(void * arg)1135 static void edt_ft5x06_disable_regulators(void *arg)
1136 {
1137 struct edt_ft5x06_ts_data *data = arg;
1138
1139 regulator_disable(data->vcc);
1140 regulator_disable(data->iovcc);
1141 }
1142
edt_ft5x06_ts_probe(struct i2c_client * client)1143 static int edt_ft5x06_ts_probe(struct i2c_client *client)
1144 {
1145 const struct i2c_device_id *id = i2c_client_get_device_id(client);
1146 const struct edt_i2c_chip_data *chip_data;
1147 struct edt_ft5x06_ts_data *tsdata;
1148 unsigned int val;
1149 struct input_dev *input;
1150 unsigned long irq_flags;
1151 int error;
1152 u32 report_rate;
1153
1154 dev_dbg(&client->dev, "probing for EDT FT5x06 I2C\n");
1155
1156 tsdata = devm_kzalloc(&client->dev, sizeof(*tsdata), GFP_KERNEL);
1157 if (!tsdata) {
1158 dev_err(&client->dev, "failed to allocate driver data.\n");
1159 return -ENOMEM;
1160 }
1161
1162 tsdata->regmap = regmap_init_i2c(client, &edt_ft5x06_i2c_regmap_config);
1163 if (IS_ERR(tsdata->regmap)) {
1164 dev_err(&client->dev, "regmap allocation failed\n");
1165 return PTR_ERR(tsdata->regmap);
1166 }
1167
1168 /*
1169 * We are not using devm_regmap_init_i2c() and instead install a
1170 * custom action because we may replace regmap with M06-specific one
1171 * and we need to make sure that it will not be released too early.
1172 */
1173 error = devm_add_action_or_reset(&client->dev, edt_ft5x06_exit_regmap,
1174 tsdata);
1175 if (error)
1176 return error;
1177
1178 chip_data = device_get_match_data(&client->dev);
1179 if (!chip_data)
1180 chip_data = (const struct edt_i2c_chip_data *)id->driver_data;
1181 if (!chip_data || !chip_data->max_support_points) {
1182 dev_err(&client->dev, "invalid or missing chip data\n");
1183 return -EINVAL;
1184 }
1185
1186 tsdata->max_support_points = chip_data->max_support_points;
1187
1188 tsdata->vcc = devm_regulator_get(&client->dev, "vcc");
1189 if (IS_ERR(tsdata->vcc))
1190 return dev_err_probe(&client->dev, PTR_ERR(tsdata->vcc),
1191 "failed to request regulator\n");
1192
1193 tsdata->iovcc = devm_regulator_get(&client->dev, "iovcc");
1194 if (IS_ERR(tsdata->iovcc)) {
1195 error = PTR_ERR(tsdata->iovcc);
1196 if (error != -EPROBE_DEFER)
1197 dev_err(&client->dev,
1198 "failed to request iovcc regulator: %d\n", error);
1199 return error;
1200 }
1201
1202 error = regulator_enable(tsdata->iovcc);
1203 if (error < 0) {
1204 dev_err(&client->dev, "failed to enable iovcc: %d\n", error);
1205 return error;
1206 }
1207
1208 /* Delay enabling VCC for > 10us (T_ivd) after IOVCC */
1209 usleep_range(10, 100);
1210
1211 error = regulator_enable(tsdata->vcc);
1212 if (error < 0) {
1213 dev_err(&client->dev, "failed to enable vcc: %d\n", error);
1214 regulator_disable(tsdata->iovcc);
1215 return error;
1216 }
1217
1218 error = devm_add_action_or_reset(&client->dev,
1219 edt_ft5x06_disable_regulators,
1220 tsdata);
1221 if (error)
1222 return error;
1223
1224 tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
1225 "reset", GPIOD_OUT_HIGH);
1226 if (IS_ERR(tsdata->reset_gpio)) {
1227 error = PTR_ERR(tsdata->reset_gpio);
1228 dev_err(&client->dev,
1229 "Failed to request GPIO reset pin, error %d\n", error);
1230 return error;
1231 }
1232
1233 tsdata->wake_gpio = devm_gpiod_get_optional(&client->dev,
1234 "wake", GPIOD_OUT_LOW);
1235 if (IS_ERR(tsdata->wake_gpio)) {
1236 error = PTR_ERR(tsdata->wake_gpio);
1237 dev_err(&client->dev,
1238 "Failed to request GPIO wake pin, error %d\n", error);
1239 return error;
1240 }
1241
1242 /*
1243 * Check which sleep modes we can support. Power-off requieres the
1244 * reset-pin to ensure correct power-down/power-up behaviour. Start with
1245 * the EDT_PMODE_POWEROFF test since this is the deepest possible sleep
1246 * mode.
1247 */
1248 if (tsdata->reset_gpio)
1249 tsdata->suspend_mode = EDT_PMODE_POWEROFF;
1250 else if (tsdata->wake_gpio)
1251 tsdata->suspend_mode = EDT_PMODE_HIBERNATE;
1252 else
1253 tsdata->suspend_mode = EDT_PMODE_NOT_SUPPORTED;
1254
1255 if (tsdata->wake_gpio) {
1256 usleep_range(5000, 6000);
1257 gpiod_set_value_cansleep(tsdata->wake_gpio, 1);
1258 usleep_range(5000, 6000);
1259 }
1260
1261 if (tsdata->reset_gpio) {
1262 usleep_range(5000, 6000);
1263 gpiod_set_value_cansleep(tsdata->reset_gpio, 0);
1264 msleep(300);
1265 }
1266
1267 input = devm_input_allocate_device(&client->dev);
1268 if (!input) {
1269 dev_err(&client->dev, "failed to allocate input device.\n");
1270 return -ENOMEM;
1271 }
1272
1273 mutex_init(&tsdata->mutex);
1274 tsdata->client = client;
1275 tsdata->input = input;
1276 tsdata->factory_mode = false;
1277 i2c_set_clientdata(client, tsdata);
1278
1279 error = edt_ft5x06_ts_identify(client, tsdata);
1280 if (error) {
1281 dev_err(&client->dev, "touchscreen probe failed\n");
1282 return error;
1283 }
1284
1285 /*
1286 * Dummy read access. EP0700MLP1 returns bogus data on the first
1287 * register read access and ignores writes.
1288 */
1289 regmap_read(tsdata->regmap, 0x00, &val);
1290
1291 edt_ft5x06_ts_set_tdata_parameters(tsdata);
1292 edt_ft5x06_ts_set_regs(tsdata);
1293 edt_ft5x06_ts_get_defaults(&client->dev, tsdata);
1294 edt_ft5x06_ts_get_parameters(tsdata);
1295
1296 if (tsdata->reg_addr.reg_report_rate != NO_REGISTER &&
1297 !device_property_read_u32(&client->dev,
1298 "report-rate-hz", &report_rate)) {
1299 if (tsdata->version == EDT_M06)
1300 tsdata->report_rate = clamp_val(report_rate, 30, 140);
1301 else
1302 tsdata->report_rate = clamp_val(report_rate, 1, 255);
1303
1304 if (report_rate != tsdata->report_rate)
1305 dev_warn(&client->dev,
1306 "report-rate %dHz is unsupported, use %dHz\n",
1307 report_rate, tsdata->report_rate);
1308
1309 if (tsdata->version == EDT_M06)
1310 tsdata->report_rate /= 10;
1311
1312 regmap_write(tsdata->regmap, tsdata->reg_addr.reg_report_rate,
1313 tsdata->report_rate);
1314 }
1315
1316 dev_dbg(&client->dev,
1317 "Model \"%s\", Rev. \"%s\", %dx%d sensors\n",
1318 tsdata->name, tsdata->fw_version, tsdata->num_x, tsdata->num_y);
1319
1320 input->name = tsdata->name;
1321 input->id.bustype = BUS_I2C;
1322 input->dev.parent = &client->dev;
1323
1324 input_set_abs_params(input, ABS_MT_POSITION_X,
1325 0, tsdata->num_x * 64 - 1, 0, 0);
1326 input_set_abs_params(input, ABS_MT_POSITION_Y,
1327 0, tsdata->num_y * 64 - 1, 0, 0);
1328
1329 touchscreen_parse_properties(input, true, &tsdata->prop);
1330
1331 error = input_mt_init_slots(input, tsdata->max_support_points,
1332 INPUT_MT_DIRECT);
1333 if (error) {
1334 dev_err(&client->dev, "Unable to init MT slots.\n");
1335 return error;
1336 }
1337
1338 irq_flags = irq_get_trigger_type(client->irq);
1339 if (irq_flags == IRQF_TRIGGER_NONE)
1340 irq_flags = IRQF_TRIGGER_FALLING;
1341 irq_flags |= IRQF_ONESHOT;
1342
1343 error = devm_request_threaded_irq(&client->dev, client->irq,
1344 NULL, edt_ft5x06_ts_isr, irq_flags,
1345 client->name, tsdata);
1346 if (error) {
1347 dev_err(&client->dev, "Unable to request touchscreen IRQ.\n");
1348 return error;
1349 }
1350
1351 error = devm_device_add_group(&client->dev, &edt_ft5x06_attr_group);
1352 if (error)
1353 return error;
1354
1355 error = input_register_device(input);
1356 if (error)
1357 return error;
1358
1359 edt_ft5x06_ts_prepare_debugfs(tsdata, dev_driver_string(&client->dev));
1360
1361 dev_dbg(&client->dev,
1362 "EDT FT5x06 initialized: IRQ %d, WAKE pin %d, Reset pin %d.\n",
1363 client->irq,
1364 tsdata->wake_gpio ? desc_to_gpio(tsdata->wake_gpio) : -1,
1365 tsdata->reset_gpio ? desc_to_gpio(tsdata->reset_gpio) : -1);
1366
1367 return 0;
1368 }
1369
edt_ft5x06_ts_remove(struct i2c_client * client)1370 static void edt_ft5x06_ts_remove(struct i2c_client *client)
1371 {
1372 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
1373
1374 edt_ft5x06_ts_teardown_debugfs(tsdata);
1375 }
1376
edt_ft5x06_ts_suspend(struct device * dev)1377 static int edt_ft5x06_ts_suspend(struct device *dev)
1378 {
1379 struct i2c_client *client = to_i2c_client(dev);
1380 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
1381 struct gpio_desc *reset_gpio = tsdata->reset_gpio;
1382 int ret;
1383
1384 if (device_may_wakeup(dev))
1385 return 0;
1386
1387 if (tsdata->suspend_mode == EDT_PMODE_NOT_SUPPORTED)
1388 return 0;
1389
1390 /* Enter hibernate mode. */
1391 ret = regmap_write(tsdata->regmap, PMOD_REGISTER_OPMODE,
1392 PMOD_REGISTER_HIBERNATE);
1393 if (ret)
1394 dev_warn(dev, "Failed to set hibernate mode\n");
1395
1396 if (tsdata->suspend_mode == EDT_PMODE_HIBERNATE)
1397 return 0;
1398
1399 /*
1400 * Power-off according the datasheet. Cut the power may leaf the irq
1401 * line in an undefined state depending on the host pull resistor
1402 * settings. Disable the irq to avoid adjusting each host till the
1403 * device is back in a full functional state.
1404 */
1405 disable_irq(tsdata->client->irq);
1406
1407 gpiod_set_value_cansleep(reset_gpio, 1);
1408 usleep_range(1000, 2000);
1409
1410 ret = regulator_disable(tsdata->vcc);
1411 if (ret)
1412 dev_warn(dev, "Failed to disable vcc\n");
1413 ret = regulator_disable(tsdata->iovcc);
1414 if (ret)
1415 dev_warn(dev, "Failed to disable iovcc\n");
1416
1417 return 0;
1418 }
1419
edt_ft5x06_ts_resume(struct device * dev)1420 static int edt_ft5x06_ts_resume(struct device *dev)
1421 {
1422 struct i2c_client *client = to_i2c_client(dev);
1423 struct edt_ft5x06_ts_data *tsdata = i2c_get_clientdata(client);
1424 int ret = 0;
1425
1426 if (device_may_wakeup(dev))
1427 return 0;
1428
1429 if (tsdata->suspend_mode == EDT_PMODE_NOT_SUPPORTED)
1430 return 0;
1431
1432 if (tsdata->suspend_mode == EDT_PMODE_POWEROFF) {
1433 struct gpio_desc *reset_gpio = tsdata->reset_gpio;
1434
1435 /*
1436 * We can't check if the regulator is a dummy or a real
1437 * regulator. So we need to specify the 5ms reset time (T_rst)
1438 * here instead of the 100us T_rtp time. We also need to wait
1439 * 300ms in case it was a real supply and the power was cutted
1440 * of. Toggle the reset pin is also a way to exit the hibernate
1441 * mode.
1442 */
1443 gpiod_set_value_cansleep(reset_gpio, 1);
1444 usleep_range(5000, 6000);
1445
1446 ret = regulator_enable(tsdata->iovcc);
1447 if (ret) {
1448 dev_err(dev, "Failed to enable iovcc\n");
1449 return ret;
1450 }
1451
1452 /* Delay enabling VCC for > 10us (T_ivd) after IOVCC */
1453 usleep_range(10, 100);
1454
1455 ret = regulator_enable(tsdata->vcc);
1456 if (ret) {
1457 dev_err(dev, "Failed to enable vcc\n");
1458 regulator_disable(tsdata->iovcc);
1459 return ret;
1460 }
1461
1462 usleep_range(1000, 2000);
1463 gpiod_set_value_cansleep(reset_gpio, 0);
1464 msleep(300);
1465
1466 edt_ft5x06_restore_reg_parameters(tsdata);
1467 enable_irq(tsdata->client->irq);
1468
1469 if (tsdata->factory_mode)
1470 ret = edt_ft5x06_factory_mode(tsdata);
1471 } else {
1472 struct gpio_desc *wake_gpio = tsdata->wake_gpio;
1473
1474 gpiod_set_value_cansleep(wake_gpio, 0);
1475 usleep_range(5000, 6000);
1476 gpiod_set_value_cansleep(wake_gpio, 1);
1477 }
1478
1479 return ret;
1480 }
1481
1482 static DEFINE_SIMPLE_DEV_PM_OPS(edt_ft5x06_ts_pm_ops,
1483 edt_ft5x06_ts_suspend, edt_ft5x06_ts_resume);
1484
1485 static const struct edt_i2c_chip_data edt_ft5x06_data = {
1486 .max_support_points = 5,
1487 };
1488
1489 static const struct edt_i2c_chip_data edt_ft5506_data = {
1490 .max_support_points = 10,
1491 };
1492
1493 static const struct edt_i2c_chip_data edt_ft6236_data = {
1494 .max_support_points = 2,
1495 };
1496
1497 static const struct i2c_device_id edt_ft5x06_ts_id[] = {
1498 { .name = "edt-ft5x06", .driver_data = (long)&edt_ft5x06_data },
1499 { .name = "edt-ft5506", .driver_data = (long)&edt_ft5506_data },
1500 { .name = "ev-ft5726", .driver_data = (long)&edt_ft5506_data },
1501 /* Note no edt- prefix for compatibility with the ft6236.c driver */
1502 { .name = "ft6236", .driver_data = (long)&edt_ft6236_data },
1503 { /* sentinel */ }
1504 };
1505 MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
1506
1507 static const struct of_device_id edt_ft5x06_of_match[] = {
1508 { .compatible = "edt,edt-ft5206", .data = &edt_ft5x06_data },
1509 { .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data },
1510 { .compatible = "edt,edt-ft5406", .data = &edt_ft5x06_data },
1511 { .compatible = "edt,edt-ft5506", .data = &edt_ft5506_data },
1512 { .compatible = "evervision,ev-ft5726", .data = &edt_ft5506_data },
1513 /* Note focaltech vendor prefix for compatibility with ft6236.c */
1514 { .compatible = "focaltech,ft6236", .data = &edt_ft6236_data },
1515 { /* sentinel */ }
1516 };
1517 MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
1518
1519 static struct i2c_driver edt_ft5x06_ts_driver = {
1520 .driver = {
1521 .name = "edt_ft5x06",
1522 .of_match_table = edt_ft5x06_of_match,
1523 .pm = pm_sleep_ptr(&edt_ft5x06_ts_pm_ops),
1524 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
1525 },
1526 .id_table = edt_ft5x06_ts_id,
1527 .probe = edt_ft5x06_ts_probe,
1528 .remove = edt_ft5x06_ts_remove,
1529 };
1530
1531 module_i2c_driver(edt_ft5x06_ts_driver);
1532
1533 MODULE_AUTHOR("Simon Budig <simon.budig@kernelconcepts.de>");
1534 MODULE_DESCRIPTION("EDT FT5x06 I2C Touchscreen Driver");
1535 MODULE_LICENSE("GPL v2");
1536