xref: /openbmc/linux/net/sched/Kconfig (revision e420bed0)
1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Traffic control configuration.
4#
5
6menuconfig NET_SCHED
7	bool "QoS and/or fair queueing"
8	select NET_SCH_FIFO
9	help
10	  When the kernel has several packets to send out over a network
11	  device, it has to decide which ones to send first, which ones to
12	  delay, and which ones to drop. This is the job of the queueing
13	  disciplines, several different algorithms for how to do this
14	  "fairly" have been proposed.
15
16	  If you say N here, you will get the standard packet scheduler, which
17	  is a FIFO (first come, first served). If you say Y here, you will be
18	  able to choose from among several alternative algorithms which can
19	  then be attached to different network devices. This is useful for
20	  example if some of your network devices are real time devices that
21	  need a certain minimum data flow rate, or if you need to limit the
22	  maximum data flow rate for traffic which matches specified criteria.
23	  This code is considered to be experimental.
24
25	  To administer these schedulers, you'll need the user-level utilities
26	  from the package iproute2+tc at
27	  <https://www.kernel.org/pub/linux/utils/net/iproute2/>.  That package
28	  also contains some documentation; for more, check out
29	  <http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2>.
30
31	  This Quality of Service (QoS) support will enable you to use
32	  Differentiated Services (diffserv) and Resource Reservation Protocol
33	  (RSVP) on your Linux router if you also say Y to the corresponding
34	  classifiers below.  Documentation and software is at
35	  <http://diffserv.sourceforge.net/>.
36
37	  If you say Y here and to "/proc file system" below, you will be able
38	  to read status information about packet schedulers from the file
39	  /proc/net/psched.
40
41	  The available schedulers are listed in the following questions; you
42	  can say Y to as many as you like. If unsure, say N now.
43
44if NET_SCHED
45
46comment "Queueing/Scheduling"
47
48config NET_SCH_HTB
49	tristate "Hierarchical Token Bucket (HTB)"
50	help
51	  Say Y here if you want to use the Hierarchical Token Buckets (HTB)
52	  packet scheduling algorithm. See
53	  <http://luxik.cdi.cz/~devik/qos/htb/> for complete manual and
54	  in-depth articles.
55
56	  HTB is very similar to CBQ regarding its goals however is has
57	  different properties and different algorithm.
58
59	  To compile this code as a module, choose M here: the
60	  module will be called sch_htb.
61
62config NET_SCH_HFSC
63	tristate "Hierarchical Fair Service Curve (HFSC)"
64	help
65	  Say Y here if you want to use the Hierarchical Fair Service Curve
66	  (HFSC) packet scheduling algorithm.
67
68	  To compile this code as a module, choose M here: the
69	  module will be called sch_hfsc.
70
71config NET_SCH_PRIO
72	tristate "Multi Band Priority Queueing (PRIO)"
73	help
74	  Say Y here if you want to use an n-band priority queue packet
75	  scheduler.
76
77	  To compile this code as a module, choose M here: the
78	  module will be called sch_prio.
79
80config NET_SCH_MULTIQ
81	tristate "Hardware Multiqueue-aware Multi Band Queuing (MULTIQ)"
82	help
83	  Say Y here if you want to use an n-band queue packet scheduler
84	  to support devices that have multiple hardware transmit queues.
85
86	  To compile this code as a module, choose M here: the
87	  module will be called sch_multiq.
88
89config NET_SCH_RED
90	tristate "Random Early Detection (RED)"
91	help
92	  Say Y here if you want to use the Random Early Detection (RED)
93	  packet scheduling algorithm.
94
95	  See the top of <file:net/sched/sch_red.c> for more details.
96
97	  To compile this code as a module, choose M here: the
98	  module will be called sch_red.
99
100config NET_SCH_SFB
101	tristate "Stochastic Fair Blue (SFB)"
102	help
103	  Say Y here if you want to use the Stochastic Fair Blue (SFB)
104	  packet scheduling algorithm.
105
106	  See the top of <file:net/sched/sch_sfb.c> for more details.
107
108	  To compile this code as a module, choose M here: the
109	  module will be called sch_sfb.
110
111config NET_SCH_SFQ
112	tristate "Stochastic Fairness Queueing (SFQ)"
113	help
114	  Say Y here if you want to use the Stochastic Fairness Queueing (SFQ)
115	  packet scheduling algorithm.
116
117	  See the top of <file:net/sched/sch_sfq.c> for more details.
118
119	  To compile this code as a module, choose M here: the
120	  module will be called sch_sfq.
121
122config NET_SCH_TEQL
123	tristate "True Link Equalizer (TEQL)"
124	help
125	  Say Y here if you want to use the True Link Equalizer (TLE) packet
126	  scheduling algorithm. This queueing discipline allows the combination
127	  of several physical devices into one virtual device.
128
129	  See the top of <file:net/sched/sch_teql.c> for more details.
130
131	  To compile this code as a module, choose M here: the
132	  module will be called sch_teql.
133
134config NET_SCH_TBF
135	tristate "Token Bucket Filter (TBF)"
136	help
137	  Say Y here if you want to use the Token Bucket Filter (TBF) packet
138	  scheduling algorithm.
139
140	  See the top of <file:net/sched/sch_tbf.c> for more details.
141
142	  To compile this code as a module, choose M here: the
143	  module will be called sch_tbf.
144
145config NET_SCH_CBS
146	tristate "Credit Based Shaper (CBS)"
147	help
148	  Say Y here if you want to use the Credit Based Shaper (CBS) packet
149	  scheduling algorithm.
150
151	  See the top of <file:net/sched/sch_cbs.c> for more details.
152
153	  To compile this code as a module, choose M here: the
154	  module will be called sch_cbs.
155
156config NET_SCH_ETF
157	tristate "Earliest TxTime First (ETF)"
158	help
159	  Say Y here if you want to use the Earliest TxTime First (ETF) packet
160	  scheduling algorithm.
161
162	  See the top of <file:net/sched/sch_etf.c> for more details.
163
164	  To compile this code as a module, choose M here: the
165	  module will be called sch_etf.
166
167config NET_SCH_MQPRIO_LIB
168	tristate
169	help
170	  Common library for manipulating mqprio queue configurations.
171
172config NET_SCH_TAPRIO
173	tristate "Time Aware Priority (taprio) Scheduler"
174	select NET_SCH_MQPRIO_LIB
175	help
176	  Say Y here if you want to use the Time Aware Priority (taprio) packet
177	  scheduling algorithm.
178
179	  See the top of <file:net/sched/sch_taprio.c> for more details.
180
181	  To compile this code as a module, choose M here: the
182	  module will be called sch_taprio.
183
184config NET_SCH_GRED
185	tristate "Generic Random Early Detection (GRED)"
186	help
187	  Say Y here if you want to use the Generic Random Early Detection
188	  (GRED) packet scheduling algorithm for some of your network devices
189	  (see the top of <file:net/sched/sch_red.c> for details and
190	  references about the algorithm).
191
192	  To compile this code as a module, choose M here: the
193	  module will be called sch_gred.
194
195config NET_SCH_NETEM
196	tristate "Network emulator (NETEM)"
197	help
198	  Say Y if you want to emulate network delay, loss, and packet
199	  re-ordering. This is often useful to simulate networks when
200	  testing applications or protocols.
201
202	  To compile this driver as a module, choose M here: the module
203	  will be called sch_netem.
204
205	  If unsure, say N.
206
207config NET_SCH_DRR
208	tristate "Deficit Round Robin scheduler (DRR)"
209	help
210	  Say Y here if you want to use the Deficit Round Robin (DRR) packet
211	  scheduling algorithm.
212
213	  To compile this driver as a module, choose M here: the module
214	  will be called sch_drr.
215
216	  If unsure, say N.
217
218config NET_SCH_MQPRIO
219	tristate "Multi-queue priority scheduler (MQPRIO)"
220	select NET_SCH_MQPRIO_LIB
221	help
222	  Say Y here if you want to use the Multi-queue Priority scheduler.
223	  This scheduler allows QOS to be offloaded on NICs that have support
224	  for offloading QOS schedulers.
225
226	  To compile this driver as a module, choose M here: the module will
227	  be called sch_mqprio.
228
229	  If unsure, say N.
230
231config NET_SCH_SKBPRIO
232	tristate "SKB priority queue scheduler (SKBPRIO)"
233	help
234	  Say Y here if you want to use the SKB priority queue
235	  scheduler. This schedules packets according to skb->priority,
236	  which is useful for request packets in DoS mitigation systems such
237	  as Gatekeeper.
238
239	  To compile this driver as a module, choose M here: the module will
240	  be called sch_skbprio.
241
242	  If unsure, say N.
243
244config NET_SCH_CHOKE
245	tristate "CHOose and Keep responsive flow scheduler (CHOKE)"
246	help
247	  Say Y here if you want to use the CHOKe packet scheduler (CHOose
248	  and Keep for responsive flows, CHOose and Kill for unresponsive
249	  flows). This is a variation of RED which tries to penalize flows
250	  that monopolize the queue.
251
252	  To compile this code as a module, choose M here: the
253	  module will be called sch_choke.
254
255config NET_SCH_QFQ
256	tristate "Quick Fair Queueing scheduler (QFQ)"
257	help
258	  Say Y here if you want to use the Quick Fair Queueing Scheduler (QFQ)
259	  packet scheduling algorithm.
260
261	  To compile this driver as a module, choose M here: the module
262	  will be called sch_qfq.
263
264	  If unsure, say N.
265
266config NET_SCH_CODEL
267	tristate "Controlled Delay AQM (CODEL)"
268	help
269	  Say Y here if you want to use the Controlled Delay (CODEL)
270	  packet scheduling algorithm.
271
272	  To compile this driver as a module, choose M here: the module
273	  will be called sch_codel.
274
275	  If unsure, say N.
276
277config NET_SCH_FQ_CODEL
278	tristate "Fair Queue Controlled Delay AQM (FQ_CODEL)"
279	help
280	  Say Y here if you want to use the FQ Controlled Delay (FQ_CODEL)
281	  packet scheduling algorithm.
282
283	  To compile this driver as a module, choose M here: the module
284	  will be called sch_fq_codel.
285
286	  If unsure, say N.
287
288config NET_SCH_CAKE
289	tristate "Common Applications Kept Enhanced (CAKE)"
290	help
291	  Say Y here if you want to use the Common Applications Kept Enhanced
292	  (CAKE) queue management algorithm.
293
294	  To compile this driver as a module, choose M here: the module
295	  will be called sch_cake.
296
297	  If unsure, say N.
298
299config NET_SCH_FQ
300	tristate "Fair Queue"
301	help
302	  Say Y here if you want to use the FQ packet scheduling algorithm.
303
304	  FQ does flow separation, and is able to respect pacing requirements
305	  set by TCP stack into sk->sk_pacing_rate (for locally generated
306	  traffic)
307
308	  To compile this driver as a module, choose M here: the module
309	  will be called sch_fq.
310
311	  If unsure, say N.
312
313config NET_SCH_HHF
314	tristate "Heavy-Hitter Filter (HHF)"
315	help
316	  Say Y here if you want to use the Heavy-Hitter Filter (HHF)
317	  packet scheduling algorithm.
318
319	  To compile this driver as a module, choose M here: the module
320	  will be called sch_hhf.
321
322config NET_SCH_PIE
323	tristate "Proportional Integral controller Enhanced (PIE) scheduler"
324	help
325	  Say Y here if you want to use the Proportional Integral controller
326	  Enhanced scheduler packet scheduling algorithm.
327	  For more information, please see https://tools.ietf.org/html/rfc8033
328
329	  To compile this driver as a module, choose M here: the module
330	  will be called sch_pie.
331
332	  If unsure, say N.
333
334config NET_SCH_FQ_PIE
335	depends on NET_SCH_PIE
336	tristate "Flow Queue Proportional Integral controller Enhanced (FQ-PIE)"
337	help
338	  Say Y here if you want to use the Flow Queue Proportional Integral
339	  controller Enhanced (FQ-PIE) packet scheduling algorithm.
340	  For more information, please see https://tools.ietf.org/html/rfc8033
341
342	  To compile this driver as a module, choose M here: the module
343	  will be called sch_fq_pie.
344
345	  If unsure, say N.
346
347config NET_SCH_INGRESS
348	tristate "Ingress/classifier-action Qdisc"
349	depends on NET_CLS_ACT
350	select NET_XGRESS
351	help
352	  Say Y here if you want to use classifiers for incoming and/or outgoing
353	  packets. This qdisc doesn't do anything else besides running classifiers,
354	  which can also have actions attached to them. In case of outgoing packets,
355	  classifiers that this qdisc holds are executed in the transmit path
356	  before real enqueuing to an egress qdisc happens.
357
358	  If unsure, say Y.
359
360	  To compile this code as a module, choose M here: the module will be
361	  called sch_ingress with alias of sch_clsact.
362
363config NET_SCH_PLUG
364	tristate "Plug network traffic until release (PLUG)"
365	help
366
367	  This queuing discipline allows userspace to plug/unplug a network
368	  output queue, using the netlink interface.  When it receives an
369	  enqueue command it inserts a plug into the outbound queue that
370	  causes following packets to enqueue until a dequeue command arrives
371	  over netlink, causing the plug to be removed and resuming the normal
372	  packet flow.
373
374	  This module also provides a generic "network output buffering"
375	  functionality (aka output commit), wherein upon arrival of a dequeue
376	  command, only packets up to the first plug are released for delivery.
377	  The Remus HA project uses this module to enable speculative execution
378	  of virtual machines by allowing the generated network output to be rolled
379	  back if needed.
380
381	  For more information, please refer to <http://wiki.xenproject.org/wiki/Remus>
382
383	  Say Y here if you are using this kernel for Xen dom0 and
384	  want to protect Xen guests with Remus.
385
386	  To compile this code as a module, choose M here: the
387	  module will be called sch_plug.
388
389config NET_SCH_ETS
390	tristate "Enhanced transmission selection scheduler (ETS)"
391	help
392          The Enhanced Transmission Selection scheduler is a classful
393          queuing discipline that merges functionality of PRIO and DRR
394          qdiscs in one scheduler. ETS makes it easy to configure a set of
395          strict and bandwidth-sharing bands to implement the transmission
396          selection described in 802.1Qaz.
397
398	  Say Y here if you want to use the ETS packet scheduling
399	  algorithm.
400
401	  To compile this driver as a module, choose M here: the module
402	  will be called sch_ets.
403
404	  If unsure, say N.
405
406menuconfig NET_SCH_DEFAULT
407	bool "Allow override default queue discipline"
408	help
409	  Support for selection of default queuing discipline.
410
411	  Nearly all users can safely say no here, and the default
412	  of pfifo_fast will be used. Many distributions already set
413	  the default value via /proc/sys/net/core/default_qdisc.
414
415	  If unsure, say N.
416
417if NET_SCH_DEFAULT
418
419choice
420	prompt "Default queuing discipline"
421	default DEFAULT_PFIFO_FAST
422	help
423	  Select the queueing discipline that will be used by default
424	  for all network devices.
425
426	config DEFAULT_FQ
427		bool "Fair Queue" if NET_SCH_FQ
428
429	config DEFAULT_CODEL
430		bool "Controlled Delay" if NET_SCH_CODEL
431
432	config DEFAULT_FQ_CODEL
433		bool "Fair Queue Controlled Delay" if NET_SCH_FQ_CODEL
434
435	config DEFAULT_FQ_PIE
436		bool "Flow Queue Proportional Integral controller Enhanced" if NET_SCH_FQ_PIE
437
438	config DEFAULT_SFQ
439		bool "Stochastic Fair Queue" if NET_SCH_SFQ
440
441	config DEFAULT_PFIFO_FAST
442		bool "Priority FIFO Fast"
443endchoice
444
445config DEFAULT_NET_SCH
446	string
447	default "pfifo_fast" if DEFAULT_PFIFO_FAST
448	default "fq" if DEFAULT_FQ
449	default "fq_codel" if DEFAULT_FQ_CODEL
450	default "fq_pie" if DEFAULT_FQ_PIE
451	default "sfq" if DEFAULT_SFQ
452	default "pfifo_fast"
453endif
454
455comment "Classification"
456
457config NET_CLS
458	bool
459
460config NET_CLS_BASIC
461	tristate "Elementary classification (BASIC)"
462	select NET_CLS
463	help
464	  Say Y here if you want to be able to classify packets using
465	  only extended matches and actions.
466
467	  To compile this code as a module, choose M here: the
468	  module will be called cls_basic.
469
470config NET_CLS_ROUTE4
471	tristate "Routing decision (ROUTE)"
472	depends on INET
473	select IP_ROUTE_CLASSID
474	select NET_CLS
475	help
476	  If you say Y here, you will be able to classify packets
477	  according to the route table entry they matched.
478
479	  To compile this code as a module, choose M here: the
480	  module will be called cls_route.
481
482config NET_CLS_FW
483	tristate "Netfilter mark (FW)"
484	select NET_CLS
485	help
486	  If you say Y here, you will be able to classify packets
487	  according to netfilter/firewall marks.
488
489	  To compile this code as a module, choose M here: the
490	  module will be called cls_fw.
491
492config NET_CLS_U32
493	tristate "Universal 32bit comparisons w/ hashing (U32)"
494	select NET_CLS
495	help
496	  Say Y here to be able to classify packets using a universal
497	  32bit pieces based comparison scheme.
498
499	  To compile this code as a module, choose M here: the
500	  module will be called cls_u32.
501
502config CLS_U32_PERF
503	bool "Performance counters support"
504	depends on NET_CLS_U32
505	help
506	  Say Y here to make u32 gather additional statistics useful for
507	  fine tuning u32 classifiers.
508
509config CLS_U32_MARK
510	bool "Netfilter marks support"
511	depends on NET_CLS_U32
512	help
513	  Say Y here to be able to use netfilter marks as u32 key.
514
515config NET_CLS_FLOW
516	tristate "Flow classifier"
517	select NET_CLS
518	help
519	  If you say Y here, you will be able to classify packets based on
520	  a configurable combination of packet keys. This is mostly useful
521	  in combination with SFQ.
522
523	  To compile this code as a module, choose M here: the
524	  module will be called cls_flow.
525
526config NET_CLS_CGROUP
527	tristate "Control Group Classifier"
528	select NET_CLS
529	select CGROUP_NET_CLASSID
530	depends on CGROUPS
531	help
532	  Say Y here if you want to classify packets based on the control
533	  cgroup of their process.
534
535	  To compile this code as a module, choose M here: the
536	  module will be called cls_cgroup.
537
538config NET_CLS_BPF
539	tristate "BPF-based classifier"
540	select NET_CLS
541	help
542	  If you say Y here, you will be able to classify packets based on
543	  programmable BPF (JIT'ed) filters as an alternative to ematches.
544
545	  To compile this code as a module, choose M here: the module will
546	  be called cls_bpf.
547
548config NET_CLS_FLOWER
549	tristate "Flower classifier"
550	select NET_CLS
551	help
552	  If you say Y here, you will be able to classify packets based on
553	  a configurable combination of packet keys and masks.
554
555	  To compile this code as a module, choose M here: the module will
556	  be called cls_flower.
557
558config NET_CLS_MATCHALL
559	tristate "Match-all classifier"
560	select NET_CLS
561	help
562	  If you say Y here, you will be able to classify packets based on
563	  nothing. Every packet will match.
564
565	  To compile this code as a module, choose M here: the module will
566	  be called cls_matchall.
567
568config NET_EMATCH
569	bool "Extended Matches"
570	select NET_CLS
571	help
572	  Say Y here if you want to use extended matches on top of classifiers
573	  and select the extended matches below.
574
575	  Extended matches are small classification helpers not worth writing
576	  a separate classifier for.
577
578	  A recent version of the iproute2 package is required to use
579	  extended matches.
580
581config NET_EMATCH_STACK
582	int "Stack size"
583	depends on NET_EMATCH
584	default "32"
585	help
586	  Size of the local stack variable used while evaluating the tree of
587	  ematches. Limits the depth of the tree, i.e. the number of
588	  encapsulated precedences. Every level requires 4 bytes of additional
589	  stack space.
590
591config NET_EMATCH_CMP
592	tristate "Simple packet data comparison"
593	depends on NET_EMATCH
594	help
595	  Say Y here if you want to be able to classify packets based on
596	  simple packet data comparisons for 8, 16, and 32bit values.
597
598	  To compile this code as a module, choose M here: the
599	  module will be called em_cmp.
600
601config NET_EMATCH_NBYTE
602	tristate "Multi byte comparison"
603	depends on NET_EMATCH
604	help
605	  Say Y here if you want to be able to classify packets based on
606	  multiple byte comparisons mainly useful for IPv6 address comparisons.
607
608	  To compile this code as a module, choose M here: the
609	  module will be called em_nbyte.
610
611config NET_EMATCH_U32
612	tristate "U32 key"
613	depends on NET_EMATCH
614	help
615	  Say Y here if you want to be able to classify packets using
616	  the famous u32 key in combination with logic relations.
617
618	  To compile this code as a module, choose M here: the
619	  module will be called em_u32.
620
621config NET_EMATCH_META
622	tristate "Metadata"
623	depends on NET_EMATCH
624	help
625	  Say Y here if you want to be able to classify packets based on
626	  metadata such as load average, netfilter attributes, socket
627	  attributes and routing decisions.
628
629	  To compile this code as a module, choose M here: the
630	  module will be called em_meta.
631
632config NET_EMATCH_TEXT
633	tristate "Textsearch"
634	depends on NET_EMATCH
635	select TEXTSEARCH
636	select TEXTSEARCH_KMP
637	select TEXTSEARCH_BM
638	select TEXTSEARCH_FSM
639	help
640	  Say Y here if you want to be able to classify packets based on
641	  textsearch comparisons.
642
643	  To compile this code as a module, choose M here: the
644	  module will be called em_text.
645
646config NET_EMATCH_CANID
647	tristate "CAN Identifier"
648	depends on NET_EMATCH && (CAN=y || CAN=m)
649	help
650	  Say Y here if you want to be able to classify CAN frames based
651	  on CAN Identifier.
652
653	  To compile this code as a module, choose M here: the
654	  module will be called em_canid.
655
656config NET_EMATCH_IPSET
657	tristate "IPset"
658	depends on NET_EMATCH && IP_SET
659	help
660	  Say Y here if you want to be able to classify packets based on
661	  ipset membership.
662
663	  To compile this code as a module, choose M here: the
664	  module will be called em_ipset.
665
666config NET_EMATCH_IPT
667	tristate "IPtables Matches"
668	depends on NET_EMATCH && NETFILTER && NETFILTER_XTABLES
669	help
670	  Say Y here to be able to classify packets based on iptables
671	  matches.
672	  Current supported match is "policy" which allows packet classification
673	  based on IPsec policy that was used during decapsulation
674
675	  To compile this code as a module, choose M here: the
676	  module will be called em_ipt.
677
678config NET_CLS_ACT
679	bool "Actions"
680	select NET_CLS
681	select NET_XGRESS
682	help
683	  Say Y here if you want to use traffic control actions. Actions
684	  get attached to classifiers and are invoked after a successful
685	  classification. They are used to overwrite the classification
686	  result, instantly drop or redirect packets, etc.
687
688	  A recent version of the iproute2 package is required to use
689	  extended matches.
690
691config NET_ACT_POLICE
692	tristate "Traffic Policing"
693	depends on NET_CLS_ACT
694	help
695	  Say Y here if you want to do traffic policing, i.e. strict
696	  bandwidth limiting. This action replaces the existing policing
697	  module.
698
699	  To compile this code as a module, choose M here: the
700	  module will be called act_police.
701
702config NET_ACT_GACT
703	tristate "Generic actions"
704	depends on NET_CLS_ACT
705	help
706	  Say Y here to take generic actions such as dropping and
707	  accepting packets.
708
709	  To compile this code as a module, choose M here: the
710	  module will be called act_gact.
711
712config GACT_PROB
713	bool "Probability support"
714	depends on NET_ACT_GACT
715	help
716	  Say Y here to use the generic action randomly or deterministically.
717
718config NET_ACT_MIRRED
719	tristate "Redirecting and Mirroring"
720	depends on NET_CLS_ACT
721	help
722	  Say Y here to allow packets to be mirrored or redirected to
723	  other devices.
724
725	  To compile this code as a module, choose M here: the
726	  module will be called act_mirred.
727
728config NET_ACT_SAMPLE
729	tristate "Traffic Sampling"
730	depends on NET_CLS_ACT
731	select PSAMPLE
732	help
733	  Say Y here to allow packet sampling tc action. The packet sample
734	  action consists of statistically choosing packets and sampling
735	  them using the psample module.
736
737	  To compile this code as a module, choose M here: the
738	  module will be called act_sample.
739
740config NET_ACT_IPT
741	tristate "IPtables targets"
742	depends on NET_CLS_ACT && NETFILTER && NETFILTER_XTABLES
743	help
744	  Say Y here to be able to invoke iptables targets after successful
745	  classification.
746
747	  To compile this code as a module, choose M here: the
748	  module will be called act_ipt.
749
750config NET_ACT_NAT
751	tristate "Stateless NAT"
752	depends on NET_CLS_ACT
753	help
754	  Say Y here to do stateless NAT on IPv4 packets.  You should use
755	  netfilter for NAT unless you know what you are doing.
756
757	  To compile this code as a module, choose M here: the
758	  module will be called act_nat.
759
760config NET_ACT_PEDIT
761	tristate "Packet Editing"
762	depends on NET_CLS_ACT
763	help
764	  Say Y here if you want to mangle the content of packets.
765
766	  To compile this code as a module, choose M here: the
767	  module will be called act_pedit.
768
769config NET_ACT_SIMP
770	tristate "Simple Example (Debug)"
771	depends on NET_CLS_ACT
772	help
773	  Say Y here to add a simple action for demonstration purposes.
774	  It is meant as an example and for debugging purposes. It will
775	  print a configured policy string followed by the packet count
776	  to the console for every packet that passes by.
777
778	  If unsure, say N.
779
780	  To compile this code as a module, choose M here: the
781	  module will be called act_simple.
782
783config NET_ACT_SKBEDIT
784	tristate "SKB Editing"
785	depends on NET_CLS_ACT
786	help
787	  Say Y here to change skb priority or queue_mapping settings.
788
789	  If unsure, say N.
790
791	  To compile this code as a module, choose M here: the
792	  module will be called act_skbedit.
793
794config NET_ACT_CSUM
795	tristate "Checksum Updating"
796	depends on NET_CLS_ACT && INET
797	select LIBCRC32C
798	help
799	  Say Y here to update some common checksum after some direct
800	  packet alterations.
801
802	  To compile this code as a module, choose M here: the
803	  module will be called act_csum.
804
805config NET_ACT_MPLS
806	tristate "MPLS manipulation"
807	depends on NET_CLS_ACT
808	help
809	  Say Y here to push or pop MPLS headers.
810
811	  If unsure, say N.
812
813	  To compile this code as a module, choose M here: the
814	  module will be called act_mpls.
815
816config NET_ACT_VLAN
817	tristate "Vlan manipulation"
818	depends on NET_CLS_ACT
819	help
820	  Say Y here to push or pop vlan headers.
821
822	  If unsure, say N.
823
824	  To compile this code as a module, choose M here: the
825	  module will be called act_vlan.
826
827config NET_ACT_BPF
828	tristate "BPF based action"
829	depends on NET_CLS_ACT
830	help
831	  Say Y here to execute BPF code on packets. The BPF code will decide
832	  if the packet should be dropped or not.
833
834	  If unsure, say N.
835
836	  To compile this code as a module, choose M here: the
837	  module will be called act_bpf.
838
839config NET_ACT_CONNMARK
840	tristate "Netfilter Connection Mark Retriever"
841	depends on NET_CLS_ACT && NETFILTER
842	depends on NF_CONNTRACK && NF_CONNTRACK_MARK
843	help
844	  Say Y here to allow retrieving of conn mark
845
846	  If unsure, say N.
847
848	  To compile this code as a module, choose M here: the
849	  module will be called act_connmark.
850
851config NET_ACT_CTINFO
852	tristate "Netfilter Connection Mark Actions"
853	depends on NET_CLS_ACT && NETFILTER
854	depends on NF_CONNTRACK && NF_CONNTRACK_MARK
855	help
856	  Say Y here to allow transfer of a connmark stored information.
857	  Current actions transfer connmark stored DSCP into
858	  ipv4/v6 diffserv and/or to transfer connmark to packet
859	  mark.  Both are useful for restoring egress based marks
860	  back onto ingress connections for qdisc priority mapping
861	  purposes.
862
863	  If unsure, say N.
864
865	  To compile this code as a module, choose M here: the
866	  module will be called act_ctinfo.
867
868config NET_ACT_SKBMOD
869	tristate "skb data modification action"
870	depends on NET_CLS_ACT
871	help
872	 Say Y here to allow modification of skb data
873
874	 If unsure, say N.
875
876	 To compile this code as a module, choose M here: the
877	 module will be called act_skbmod.
878
879config NET_ACT_IFE
880	tristate "Inter-FE action based on IETF ForCES InterFE LFB"
881	depends on NET_CLS_ACT
882	select NET_IFE
883	help
884	  Say Y here to allow for sourcing and terminating metadata
885	  For details refer to netdev01 paper:
886	  "Distributing Linux Traffic Control Classifier-Action Subsystem"
887	   Authors: Jamal Hadi Salim and Damascene M. Joachimpillai
888
889	  To compile this code as a module, choose M here: the
890	  module will be called act_ife.
891
892config NET_ACT_TUNNEL_KEY
893	tristate "IP tunnel metadata manipulation"
894	depends on NET_CLS_ACT
895	help
896	  Say Y here to set/release ip tunnel metadata.
897
898	  If unsure, say N.
899
900	  To compile this code as a module, choose M here: the
901	  module will be called act_tunnel_key.
902
903config NET_ACT_CT
904	tristate "connection tracking tc action"
905	depends on NET_CLS_ACT && NF_CONNTRACK && (!NF_NAT || NF_NAT) && NF_FLOW_TABLE
906	select NF_CONNTRACK_OVS
907	select NF_NAT_OVS if NF_NAT
908	help
909	  Say Y here to allow sending the packets to conntrack module.
910
911	  If unsure, say N.
912
913	  To compile this code as a module, choose M here: the
914	  module will be called act_ct.
915
916config NET_ACT_GATE
917	tristate "Frame gate entry list control tc action"
918	depends on NET_CLS_ACT
919	help
920	  Say Y here to allow to control the ingress flow to be passed at
921	  specific time slot and be dropped at other specific time slot by
922	  the gate entry list.
923
924	  If unsure, say N.
925	  To compile this code as a module, choose M here: the
926	  module will be called act_gate.
927
928config NET_IFE_SKBMARK
929	tristate "Support to encoding decoding skb mark on IFE action"
930	depends on NET_ACT_IFE
931
932config NET_IFE_SKBPRIO
933	tristate "Support to encoding decoding skb prio on IFE action"
934	depends on NET_ACT_IFE
935
936config NET_IFE_SKBTCINDEX
937	tristate "Support to encoding decoding skb tcindex on IFE action"
938	depends on NET_ACT_IFE
939
940config NET_TC_SKB_EXT
941	bool "TC recirculation support"
942	depends on NET_CLS_ACT
943	select SKB_EXTENSIONS
944
945	help
946	  Say Y here to allow tc chain misses to continue in OvS datapath in
947	  the correct recirc_id, and hardware chain misses to continue in
948	  the correct chain in tc software datapath.
949
950	  Say N here if you won't be using tc<->ovs offload or tc chains offload.
951
952endif # NET_SCHED
953
954config NET_SCH_FIFO
955	bool
956