/* * Copyright (C) 2013 Gateworks Corporation * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __CONFIG_H #define __CONFIG_H /* SPL */ /* Location in NAND to read U-Boot from */ #define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * SZ_1M) /* Falcon Mode */ #define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000 /* Falcon Mode - NAND support: args@17MB kernel@18MB */ #define CONFIG_SYS_NAND_SPL_KERNEL_OFFS (18 * SZ_1M) /* Falcon Mode - MMC support: args@1MB kernel@2MB */ #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */ #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512) #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */ #include "imx6_spl.h" /* common IMX6 SPL configuration */ #include "mx6_common.h" #define CONFIG_DISPLAY_BOARDINFO_LATE #define CONFIG_MACH_TYPE 4520 /* Gateworks Ventana Platform */ /* Serial ATAG */ #define CONFIG_SERIAL_TAG /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) /* Init Functions */ #define CONFIG_MISC_INIT_R /* Driver Model */ #ifndef CONFIG_SPL_BUILD #define CONFIG_DM_GPIO #define CONFIG_DM_THERMAL #endif /* Thermal */ #define CONFIG_IMX_THERMAL /* Serial */ #define CONFIG_MXC_UART #define CONFIG_MXC_UART_BASE UART2_BASE #ifdef CONFIG_SPI_FLASH /* SPI */ #ifdef CONFIG_CMD_SF #define CONFIG_MXC_SPI #define CONFIG_SPI_FLASH_MTD #define CONFIG_SPI_FLASH_BAR #define CONFIG_SF_DEFAULT_BUS 0 #define CONFIG_SF_DEFAULT_CS 0 /* GPIO 3-19 (21248) */ #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) #endif #elif defined(CONFIG_SPL_NAND_SUPPORT) /* Enable NAND support */ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_MXS #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x40000000 #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_ONFI_DETECTION /* DMA stuff, needed for GPMI/MXS NAND support */ #define CONFIG_APBH_DMA #define CONFIG_APBH_DMA_BURST #define CONFIG_APBH_DMA_BURST8 #endif #endif /* CONFIG_SPI_FLASH */ /* I2C Configs */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ #define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ #define CONFIG_SYS_I2C_SPEED 100000 #define CONFIG_I2C_GSC 0 #define CONFIG_I2C_EDID /* MMC Configs */ #define CONFIG_SYS_FSL_ESDHC_ADDR 0 /* eMMC Configs */ #define CONFIG_SUPPORT_EMMC_BOOT #define CONFIG_SUPPORT_EMMC_RPMB /* * SATA Configs */ #ifdef CONFIG_CMD_SATA #define CONFIG_SYS_SATA_MAX_DEVICE 1 #define CONFIG_DWC_AHSATA_PORT_ID 0 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR #define CONFIG_LBA48 #endif /* * PCI express */ #ifdef CONFIG_CMD_PCI #define CONFIG_PCI_SCAN_SHOW #define CONFIG_PCI_FIXUP_DEV #define CONFIG_PCIE_IMX #endif /* * PMIC */ #define CONFIG_POWER #define CONFIG_POWER_I2C #define CONFIG_POWER_PFUZE100 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08 #define CONFIG_POWER_LTC3676 #define CONFIG_POWER_LTC3676_I2C_ADDR 0x3c /* Various command support */ #define CONFIG_CMD_UNZIP /* gzwrite */ /* Ethernet support */ #define CONFIG_FEC_MXC #define CONFIG_MII #define IMX_FEC_BASE ENET_BASE_ADDR #define CONFIG_FEC_XCV_TYPE RGMII #define CONFIG_FEC_MXC_PHYADDR 0 #define CONFIG_ARP_TIMEOUT 200UL /* USB Configs */ #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */ #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) #define CONFIG_MXC_USB_FLAGS 0 #define CONFIG_USBD_HS #define CONFIG_NETCONSOLE /* Framebuffer and LCD */ #define CONFIG_VIDEO_IPUV3 #define CONFIG_VIDEO_LOGO #define CONFIG_IMX_HDMI #define CONFIG_IMX_VIDEO_SKIP #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_SPLASH_SCREEN_ALIGN #define CONFIG_HIDE_LOGO_VERSION /* Custom config to hide U-boot version */ /* Miscellaneous configurable options */ #define CONFIG_HWCONFIG #define CONFIG_PREBOOT /* Memory configuration */ #define CONFIG_SYS_MEMTEST_START 0x10000000 #define CONFIG_SYS_MEMTEST_END 0x10010000 #define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 /* Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 1 #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE #define CONFIG_SYS_INIT_SP_OFFSET \ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) /* * MTD Command for mtdparts */ #define CONFIG_MTD_DEVICE #define CONFIG_MTD_PARTITIONS /* Persistent Environment Config */ #if defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_SYS_MMC_ENV_DEV 0 #define CONFIG_SYS_MMC_ENV_PART 1 #define CONFIG_ENV_OFFSET (709 * SZ_1K) #define CONFIG_ENV_SIZE (128 * SZ_1K) #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (128 * SZ_1K)) #elif defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_OFFSET (16 * SZ_1M) #define CONFIG_ENV_SECT_SIZE (128 * SZ_1K) #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (512 * SZ_1K)) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH) #define CONFIG_ENV_OFFSET (512 * SZ_1K) #define CONFIG_ENV_SECT_SIZE (64 * SZ_1K) #define CONFIG_ENV_SIZE (8 * SZ_1K) #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED #endif /* Environment */ #define CONFIG_IPADDR 192.168.1.1 #define CONFIG_SERVERIP 192.168.1.146 #define CONFIG_EXTRA_ENV_SETTINGS_COMMON \ "pcidisable=1\0" \ "splashpos=m,m\0" \ "usb_pgood_delay=2000\0" \ "console=ttymxc1\0" \ "bootdevs=usb mmc sata flash\0" \ "hwconfig=_UNKNOWN_\0" \ "video=\0" \ \ "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \ "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \ "disk=0\0" \ "part=1\0" \ \ "fdt_high=0xffffffff\0" \ "fdt_addr=0x18000000\0" \ "initrd_high=0xffffffff\0" \ "fixfdt=" \ "fdt addr ${fdt_addr}\0" \ "bootdir=boot\0" \ "loadfdt=" \ "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \ "echo Loaded DTB from ${bootdir}/${fdt_file}; " \ "run fixfdt; " \ "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \ "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \ "run fixfdt; " \ "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \ "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \ "run fixfdt; " \ "fi\0" \ \ "fs=ext4\0" \ "script=6x_bootscript-ventana\0" \ "loadscript=" \ "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \ "source ${loadaddr}; " \ "fi\0" \ \ "uimage=uImage\0" \ "mmc_root=mmcblk0p1\0" \ "mmc_boot=" \ "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \ "mmc dev ${disk} && mmc rescan && " \ "setenv dtype mmc; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ "root=/dev/${mmc_root} rootfstype=${fs} " \ "rootwait rw ${video} ${extra}; " \ "if run loadfdt; then " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "bootm; " \ "fi; " \ "fi\0" \ \ "sata_boot=" \ "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \ "sata init && " \ "setenv dtype sata; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ "root=/dev/sda1 rootfstype=${fs} " \ "rootwait rw ${video} ${extra}; " \ "if run loadfdt; then " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "bootm; " \ "fi; " \ "fi\0" \ "usb_boot=" \ "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \ "usb start && usb dev ${disk} && " \ "setenv dtype usb; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ "root=/dev/sda1 rootfstype=${fs} " \ "rootwait rw ${video} ${extra}; " \ "if run loadfdt; then " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "bootm; " \ "fi; " \ "fi\0" #ifdef CONFIG_SPI_FLASH #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_EXTRA_ENV_SETTINGS_COMMON \ "image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \ "image_uboot=ventana/u-boot_spi.imx\0" \ \ "spi_koffset=0x90000\0" \ "spi_klen=0x200000\0" \ \ "spi_updateuboot=echo Updating uboot from " \ "${serverip}:${image_uboot}...; " \ "tftpboot ${loadaddr} ${image_uboot} && " \ "sf probe && sf erase 0 80000 && " \ "sf write ${loadaddr} 400 ${filesize}\0" \ "spi_update=echo Updating OS from ${serverip}:${image_os} " \ "to ${spi_koffset} ...; " \ "tftp ${loadaddr} ${image_os} && " \ "sf probe && " \ "sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \ \ "flash_boot=" \ "if sf probe && " \ "sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \ "setenv bootargs console=${console},${baudrate} " \ "root=/dev/mtdblock3 " \ "rootfstype=squashfs,jffs2 " \ "${video} ${extra}; " \ "bootm; " \ "fi\0" #else #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_EXTRA_ENV_SETTINGS_COMMON \ \ "image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \ "nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \ "tftp ${loadaddr} ${image_rootfs} && " \ "nand erase.part rootfs && " \ "nand write ${loadaddr} rootfs ${filesize}\0" \ \ "flash_boot=" \ "setenv fsload 'ubifsload'; " \ "ubi part rootfs; " \ "if ubi check boot; then " \ "ubifsmount ubi0:boot; " \ "setenv root ubi0:rootfs ubi.mtd=2 " \ "rootfstype=squashfs,ubifs; " \ "setenv bootdir; " \ "elif ubi check rootfs; then " \ "ubifsmount ubi0:rootfs; " \ "setenv root ubi0:rootfs ubi.mtd=2 " \ "rootfstype=ubifs; " \ "fi; " \ "setenv dtype nand; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ "root=${root} ${video} ${extra}; " \ "if run loadfdt; then " \ "ubifsumount; " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "ubifsumount; bootm; " \ "fi; " \ "fi\0" #endif #define CONFIG_BOOTCOMMAND \ "for btype in ${bootdevs}; do " \ "echo; echo Attempting ${btype} boot...; " \ "if run ${btype}_boot; then; fi; " \ "done" #endif /* __CONFIG_H */