// SPDX-License-Identifier: GPL-2.0+ /* * ASPEED AST2500 FMC/SPI Controller driver * * Copyright (c) 2015-2018, IBM Corporation. */ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include #include #include #include #include #include #include #define ASPEED_SPI_MAX_CS 3 struct aspeed_spi_regs { u32 conf; /* 0x00 CE Type Setting */ u32 ctrl; /* 0x04 Control */ u32 intr_ctrl; /* 0x08 Interrupt Control and Status */ u32 cmd_ctrl; /* 0x0c Command Control */ u32 ce_ctrl[ASPEED_SPI_MAX_CS]; /* 0x10 .. 0x18 CEx Control */ u32 _reserved0[5]; /* .. */ u32 segment_addr[ASPEED_SPI_MAX_CS]; /* 0x30 .. 0x38 Segment Address */ u32 _reserved1[17]; /* .. */ u32 dma_ctrl; /* 0x80 DMA Control/Status */ u32 dma_flash_addr; /* 0x84 DMA Flash Side Address */ u32 dma_dram_addr; /* 0x88 DMA DRAM Side Address */ u32 dma_len; /* 0x8c DMA Length Register */ u32 dma_checksum; /* 0x90 Checksum Calculation Result */ u32 timings; /* 0x94 Read Timing Compensation */ /* not used */ u32 soft_strap_status; /* 0x9c Software Strap Status */ u32 write_cmd_filter_ctrl; /* 0xa0 Write Command Filter Control */ u32 write_addr_filter_ctrl; /* 0xa4 Write Address Filter Control */ u32 lock_ctrl_reset; /* 0xa8 Lock Control (SRST#) */ u32 lock_ctrl_wdt; /* 0xac Lock Control (Watchdog) */ u32 write_addr_filter[5]; /* 0xb0 Write Address Filter */ }; /* CE Type Setting Register */ #define CONF_ENABLE_W2 BIT(18) #define CONF_ENABLE_W1 BIT(17) #define CONF_ENABLE_W0 BIT(16) #define CONF_FLASH_TYPE2 4 #define CONF_FLASH_TYPE1 2 /* Hardwired to SPI */ #define CONF_FLASH_TYPE0 0 /* Hardwired to SPI */ #define CONF_FLASH_TYPE_NOR 0x0 #define CONF_FLASH_TYPE_SPI 0x2 /* CE Control Register */ #define CTRL_EXTENDED2 BIT(2) /* 32 bit addressing for SPI */ #define CTRL_EXTENDED1 BIT(1) /* 32 bit addressing for SPI */ #define CTRL_EXTENDED0 BIT(0) /* 32 bit addressing for SPI */ /* Interrupt Control and Status Register */ #define INTR_CTRL_DMA_STATUS BIT(11) #define INTR_CTRL_CMD_ABORT_STATUS BIT(10) #define INTR_CTRL_WRITE_PROTECT_STATUS BIT(9) #define INTR_CTRL_DMA_EN BIT(3) #define INTR_CTRL_CMD_ABORT_EN BIT(2) #define INTR_CTRL_WRITE_PROTECT_EN BIT(1) /* CEx Control Register */ #define CE_CTRL_IO_MODE_MASK GENMASK(31, 28) #define CE_CTRL_IO_DUAL_DATA BIT(29) #define CE_CTRL_IO_DUAL_ADDR_DATA (BIT(29) | BIT(28)) #define CE_CTRL_IO_QUAD_DATA BIT(30) #define CE_CTRL_IO_QUAD_ADDR_DATA (BIT(30) | BIT(28)) #define CE_CTRL_CMD_SHIFT 16 #define CE_CTRL_CMD_MASK 0xff #define CE_CTRL_CMD(cmd) \ (((cmd) & CE_CTRL_CMD_MASK) << CE_CTRL_CMD_SHIFT) #define CE_CTRL_DUMMY_HIGH_SHIFT 14 #define CE_CTRL_DUMMY_HIGH_MASK 0x1 #define CE_CTRL_CLOCK_FREQ_SHIFT 8 #define CE_CTRL_CLOCK_FREQ_MASK 0xf #define CE_CTRL_CLOCK_FREQ(div) \ (((div) & CE_CTRL_CLOCK_FREQ_MASK) << CE_CTRL_CLOCK_FREQ_SHIFT) #define CE_G6_CTRL_CLOCK_FREQ(div) \ ((((div) & CE_CTRL_CLOCK_FREQ_MASK) << CE_CTRL_CLOCK_FREQ_SHIFT) | (((div) & 0xf0) << 20)) #define CE_CTRL_DUMMY_LOW_SHIFT 6 /* 2 bits [7:6] */ #define CE_CTRL_DUMMY_LOW_MASK 0x3 #define CE_CTRL_DUMMY(dummy) \ (((((dummy) >> 2) & CE_CTRL_DUMMY_HIGH_MASK) \ << CE_CTRL_DUMMY_HIGH_SHIFT) | \ (((dummy) & CE_CTRL_DUMMY_LOW_MASK) << CE_CTRL_DUMMY_LOW_SHIFT)) #define CE_CTRL_STOP_ACTIVE BIT(2) #define CE_CTRL_MODE_MASK 0x3 #define CE_CTRL_READMODE 0x0 #define CE_CTRL_FREADMODE 0x1 #define CE_CTRL_WRITEMODE 0x2 #define CE_CTRL_USERMODE 0x3 /* * The Segment Register uses a 8MB unit to encode the start address * and the end address of the AHB window of a SPI flash device. * Default segment addresses are : * * CE0 0x20000000 - 0x2fffffff 128MB * CE1 0x28000000 - 0x29ffffff 32MB * CE2 0x2a000000 - 0x2bffffff 32MB * * The full address space of the AHB window of the controller is * covered and CE0 start address and CE2 end addresses are read-only. */ #define SEGMENT_ADDR_START(reg) ((((reg) >> 16) & 0xff) << 23) #define SEGMENT_ADDR_END(reg) ((((reg) >> 24) & 0xff) << 23) #define SEGMENT_ADDR_VALUE(start, end) \ (((((start) >> 23) & 0xff) << 16) | ((((end) >> 23) & 0xff) << 24)) #define G6_SEGMENT_ADDR_START(reg) (reg & 0xffff) #define G6_SEGMENT_ADDR_END(reg) ((reg >> 16) & 0xffff) #define G6_SEGMENT_ADDR_VALUE(start, end) \ ((((start) >> 16) & 0xffff) | (((end) - 0x100000) & 0xfff00000)) /* DMA Control/Status Register */ #define DMA_CTRL_DELAY_SHIFT 8 #define DMA_CTRL_DELAY_MASK 0xf #define DMA_CTRL_FREQ_SHIFT 4 #define DMA_CTRL_FREQ_MASK 0xf #define TIMING_MASK(div, delay) \ (((delay & DMA_CTRL_DELAY_MASK) << DMA_CTRL_DELAY_SHIFT) | \ ((div & DMA_CTRL_FREQ_MASK) << DMA_CTRL_FREQ_SHIFT)) #define DMA_CTRL_CALIB BIT(3) #define DMA_CTRL_CKSUM BIT(2) #define DMA_CTRL_WRITE BIT(1) #define DMA_CTRL_ENABLE BIT(0) /* * */ struct aspeed_spi_flash { u8 cs; bool init; /* Initialized when the SPI bus is * first claimed */ void __iomem *ahb_base; /* AHB Window for this device */ u32 ahb_size; /* AHB Window segment size */ u32 ce_ctrl_user; /* CE Control Register for USER mode */ u32 ce_ctrl_fread; /* CE Control Register for FREAD mode */ u32 iomode; struct spi_flash *spi; /* Associated SPI Flash device */ }; struct aspeed_spi_priv { struct aspeed_spi_regs *regs; void __iomem *ahb_base; /* AHB Window for all flash devices */ int new_ver; u32 ahb_size; /* AHB Window segments size */ ulong hclk_rate; /* AHB clock rate */ u32 max_hz; u8 num_cs; bool is_fmc; struct aspeed_spi_flash flashes[ASPEED_SPI_MAX_CS]; u32 flash_count; u8 cmd_buf[16]; /* SPI command in progress */ size_t cmd_len; }; static struct aspeed_spi_flash *aspeed_spi_get_flash(struct udevice *dev) { struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); struct aspeed_spi_priv *priv = dev_get_priv(dev->parent); u8 cs = slave_plat->cs; if (cs >= priv->flash_count) { pr_err("invalid CS %u\n", cs); return NULL; } return &priv->flashes[cs]; } static u32 aspeed_g6_spi_hclk_divisor(struct aspeed_spi_priv *priv, u32 max_hz) { u32 hclk_rate = priv->hclk_rate; /* HCLK/1 .. HCLK/16 */ const u8 hclk_masks[] = { 15, 7, 14, 6, 13, 5, 12, 4, 11, 3, 10, 2, 9, 1, 8, 0 }; u8 base_div = 0; // int done = 0; u32 i, j; u32 hclk_div_setting = 0; //for ast2600 spi freq = hclk / (([27:24] * 16) + [11:8]) for (j = 0; j < ARRAY_SIZE(hclk_masks); i++) { for (i = 0; i < ARRAY_SIZE(hclk_masks); i++) { if (max_hz >= (hclk_rate / ((i + 1) + (j * 16)))) { base_div = j * 16; // done = 1; break; } } // if (done) // break; if( j == 0) break; // todo check } debug("hclk=%d required=%d base_div is %d (mask %x, base_div %x) speed=%d\n", hclk_rate, max_hz, i + 1, hclk_masks[i], base_div, hclk_rate / ((i + 1) + base_div)); hclk_div_setting = ((j << 4) | hclk_masks[i]); return hclk_div_setting; } static u32 aspeed_spi_hclk_divisor(struct aspeed_spi_priv *priv, u32 max_hz) { u32 hclk_rate = priv->hclk_rate; /* HCLK/1 .. HCLK/16 */ const u8 hclk_masks[] = { 15, 7, 14, 6, 13, 5, 12, 4, 11, 3, 10, 2, 9, 1, 8, 0 }; u32 i; u32 hclk_div_setting = 0; for (i = 0; i < ARRAY_SIZE(hclk_masks); i++) { if (max_hz >= (hclk_rate / (i + 1))) break; } debug("hclk=%d required=%d divisor is %d (mask %x) speed=%d\n", hclk_rate, max_hz, i + 1, hclk_masks[i], hclk_rate / (i + 1)); hclk_div_setting = hclk_masks[i]; return hclk_div_setting; } /* * Use some address/size under the first flash device CE0 */ static u32 aspeed_spi_fmc_checksum(struct aspeed_spi_priv *priv, u8 div, u8 delay) { u32 flash_addr = (u32)priv->ahb_base + 0x10000; u32 flash_len = 0x200; u32 dma_ctrl; u32 checksum; writel(flash_addr, &priv->regs->dma_flash_addr); writel(flash_len, &priv->regs->dma_len); /* * When doing calibration, the SPI clock rate in the CE0 * Control Register and the data input delay cycles in the * Read Timing Compensation Register are replaced by bit[11:4]. */ dma_ctrl = DMA_CTRL_ENABLE | DMA_CTRL_CKSUM | DMA_CTRL_CALIB | TIMING_MASK(div, delay); writel(dma_ctrl, &priv->regs->dma_ctrl); while (!(readl(&priv->regs->intr_ctrl) & INTR_CTRL_DMA_STATUS)) ; writel(0x0, &priv->regs->intr_ctrl); checksum = readl(&priv->regs->dma_checksum); writel(0x0, &priv->regs->dma_ctrl); return checksum; } static u32 aspeed_spi_read_checksum(struct aspeed_spi_priv *priv, u8 div, u8 delay) { /* TODO(clg@kaod.org): the SPI controllers do not have the DMA * registers. The algorithm is the same. */ if (!priv->is_fmc) { pr_warn("No timing calibration support for SPI controllers"); return 0xbadc0de; } return aspeed_spi_fmc_checksum(priv, div, delay); } #define TIMING_DELAY_DI_4NS BIT(3) #define TIMING_DELAY_HCYCLE_MAX 5 static int aspeed_spi_timing_calibration(struct aspeed_spi_priv *priv) { /* HCLK/5 .. HCLK/1 */ const u8 hclk_masks[] = { 13, 6, 14, 7, 15 }; u32 timing_reg = 0; u32 checksum, gold_checksum; int i, hcycle; debug("Read timing calibration :\n"); /* Compute reference checksum at lowest freq HCLK/16 */ gold_checksum = aspeed_spi_read_checksum(priv, 0, 0); /* * Set CE0 Control Register to FAST READ command mode. The * HCLK divisor will be set through the DMA Control Register. */ writel(CE_CTRL_CMD(0xb) | CE_CTRL_DUMMY(1) | CE_CTRL_FREADMODE, &priv->regs->ce_ctrl[0]); /* Increase HCLK freq */ if (priv->new_ver) { for (i = 0; i < ARRAY_SIZE(hclk_masks) - 1; i++) { u32 hdiv = 5 - i; u32 hshift = (hdiv - 1) << 2; bool pass = false; u8 delay; if (priv->hclk_rate / hdiv > priv->max_hz) { debug("skipping freq %ld\n", priv->hclk_rate / hdiv); continue; } /* Increase HCLK cycles until read succeeds */ for (hcycle = 0; hcycle <= TIMING_DELAY_HCYCLE_MAX; hcycle++) { /* Try first with a 4ns DI delay */ delay = TIMING_DELAY_DI_4NS | hcycle; checksum = aspeed_spi_read_checksum(priv, hclk_masks[i], delay); pass = (checksum == gold_checksum); debug(" HCLK/%d, 4ns DI delay, %d HCLK cycle : %s\n", hdiv, hcycle, pass ? "PASS" : "FAIL"); /* Try again with more HCLK cycles */ if (!pass) continue; /* Try without the 4ns DI delay */ delay = hcycle; checksum = aspeed_spi_read_checksum(priv, hclk_masks[i], delay); pass = (checksum == gold_checksum); debug(" HCLK/%d, no DI delay, %d HCLK cycle : %s\n", hdiv, hcycle, pass ? "PASS" : "FAIL"); /* All good for this freq */ if (pass) break; } if (pass) { timing_reg &= ~(0xfu << hshift); timing_reg |= delay << hshift; } } } else { for (i = 0; i < ARRAY_SIZE(hclk_masks); i++) { u32 hdiv = 5 - i; u32 hshift = (hdiv - 1) << 2; bool pass = false; u8 delay; if (priv->hclk_rate / hdiv > priv->max_hz) { debug("skipping freq %ld\n", priv->hclk_rate / hdiv); continue; } /* Increase HCLK cycles until read succeeds */ for (hcycle = 0; hcycle <= TIMING_DELAY_HCYCLE_MAX; hcycle++) { /* Try first with a 4ns DI delay */ delay = TIMING_DELAY_DI_4NS | hcycle; checksum = aspeed_spi_read_checksum(priv, hclk_masks[i], delay); pass = (checksum == gold_checksum); debug(" HCLK/%d, 4ns DI delay, %d HCLK cycle : %s\n", hdiv, hcycle, pass ? "PASS" : "FAIL"); /* Try again with more HCLK cycles */ if (!pass) continue; /* Try without the 4ns DI delay */ delay = hcycle; checksum = aspeed_spi_read_checksum(priv, hclk_masks[i], delay); pass = (checksum == gold_checksum); debug(" HCLK/%d, no DI delay, %d HCLK cycle : %s\n", hdiv, hcycle, pass ? "PASS" : "FAIL"); /* All good for this freq */ if (pass) break; } if (pass) { timing_reg &= ~(0xfu << hshift); timing_reg |= delay << hshift; } } } debug("Read Timing Compensation set to 0x%08x\n", timing_reg); writel(timing_reg, &priv->regs->timings); /* Reset CE0 Control Register */ writel(0x0, &priv->regs->ce_ctrl[0]); return 0; } static int aspeed_spi_controller_init(struct aspeed_spi_priv *priv) { int cs, ret; /* * Enable write on all flash devices as USER command mode * requires it. */ setbits_le32(&priv->regs->conf, CONF_ENABLE_W2 | CONF_ENABLE_W1 | CONF_ENABLE_W0); /* * Set the Read Timing Compensation Register. This setting * applies to all devices. */ ret = aspeed_spi_timing_calibration(priv); if (ret) return ret; /* * Set safe default settings for each device. These will be * tuned after the SPI flash devices are probed. */ if (priv->new_ver) { for (cs = 0; cs < priv->flash_count; cs++) { struct aspeed_spi_flash *flash = &priv->flashes[cs]; u32 seg_addr = readl(&priv->regs->segment_addr[cs]); u32 addr_config = 0; switch(cs) { case 0: flash->ahb_base = cs ? (void *)G6_SEGMENT_ADDR_START(seg_addr) : priv->ahb_base; debug("cs0 mem-map : %x \n", (u32)flash->ahb_base); break; case 1: flash->ahb_base = priv->flashes[0].ahb_base + 0x8000000; //cs0 + 128Mb debug("cs1 mem-map : %x end %x \n", (u32)flash->ahb_base, (u32)flash->ahb_base + 0x8000000); addr_config = G6_SEGMENT_ADDR_VALUE((u32)flash->ahb_base, (u32)flash->ahb_base + 0x8000000); //add 128Mb writel(addr_config, &priv->regs->segment_addr[cs]); break; case 2: flash->ahb_base = priv->flashes[0].ahb_base + 0xc000000; //cs0 + 196Mb printf("cs2 mem-map : %x \n", (u32)flash->ahb_base); break; } flash->cs = cs; flash->ce_ctrl_user = CE_CTRL_USERMODE; flash->ce_ctrl_fread = CE_CTRL_READMODE; } } else { for (cs = 0; cs < priv->flash_count; cs++) { struct aspeed_spi_flash *flash = &priv->flashes[cs]; u32 seg_addr = readl(&priv->regs->segment_addr[cs]); /* * The start address of the AHB window of CE0 is * read-only and is the same as the address of the * overall AHB window of the controller for all flash * devices. */ flash->ahb_base = cs ? (void *)SEGMENT_ADDR_START(seg_addr) : priv->ahb_base; flash->cs = cs; flash->ce_ctrl_user = CE_CTRL_USERMODE; flash->ce_ctrl_fread = CE_CTRL_READMODE; } } return 0; } static int aspeed_spi_read_from_ahb(void __iomem *ahb_base, void *buf, size_t len) { size_t offset = 0; if (!((uintptr_t)buf % 4)) { readsl(ahb_base, buf, len >> 2); offset = len & ~0x3; len -= offset; } readsb(ahb_base, (u8 *)buf + offset, len); return 0; } static int aspeed_spi_write_to_ahb(void __iomem *ahb_base, const void *buf, size_t len) { size_t offset = 0; if (!((uintptr_t)buf % 4)) { writesl(ahb_base, buf, len >> 2); offset = len & ~0x3; len -= offset; } writesb(ahb_base, (u8 *)buf + offset, len); return 0; } static void aspeed_spi_start_user(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash) { u32 ctrl_reg = flash->ce_ctrl_user | CE_CTRL_STOP_ACTIVE; /* Deselect CS and set USER command mode */ writel(ctrl_reg, &priv->regs->ce_ctrl[flash->cs]); /* Select CS */ clrbits_le32(&priv->regs->ce_ctrl[flash->cs], CE_CTRL_STOP_ACTIVE); } static void aspeed_spi_stop_user(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash) { /* Deselect CS first */ setbits_le32(&priv->regs->ce_ctrl[flash->cs], CE_CTRL_STOP_ACTIVE); /* Restore default command mode */ writel(flash->ce_ctrl_fread, &priv->regs->ce_ctrl[flash->cs]); } static int aspeed_spi_read_reg(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, u8 opcode, u8 *read_buf, int len) { aspeed_spi_start_user(priv, flash); aspeed_spi_write_to_ahb(flash->ahb_base, &opcode, 1); aspeed_spi_read_from_ahb(flash->ahb_base, read_buf, len); aspeed_spi_stop_user(priv, flash); return 0; } static int aspeed_spi_write_reg(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, u8 opcode, const u8 *write_buf, int len) { aspeed_spi_start_user(priv, flash); aspeed_spi_write_to_ahb(flash->ahb_base, &opcode, 1); aspeed_spi_write_to_ahb(flash->ahb_base, write_buf, len); aspeed_spi_stop_user(priv, flash); switch(opcode) { case SPINOR_OP_EN4B: writel(readl(&priv->regs->ctrl) | BIT(flash->cs), &priv->regs->ctrl); break; case SPINOR_OP_EX4B: writel(readl(&priv->regs->ctrl) & ~BIT(flash->cs), &priv->regs->ctrl); break; } return 0; } static void aspeed_spi_send_cmd_addr(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, const u8 *cmdbuf, unsigned int cmdlen) { int i; u8 byte0 = 0x0; u8 addrlen = cmdlen - 1; /* First, send the opcode */ aspeed_spi_write_to_ahb(flash->ahb_base, &cmdbuf[0], 1); /* * The controller is configured for 4BYTE address mode. Fix * the address width and send an extra byte if the SPI Flash * layer uses 3 bytes addresses. */ if (addrlen == 3 && readl(&priv->regs->ctrl) & BIT(flash->cs)) aspeed_spi_write_to_ahb(flash->ahb_base, &byte0, 1); /* Then the address */ for (i = 1 ; i < cmdlen; i++) aspeed_spi_write_to_ahb(flash->ahb_base, &cmdbuf[i], 1); } static ssize_t aspeed_spi_read_user(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, unsigned int cmdlen, const u8 *cmdbuf, unsigned int len, u8 *read_buf) { u8 dummy = 0xff; int i; aspeed_spi_start_user(priv, flash); /* cmd buffer = cmd + addr + dummies */ aspeed_spi_send_cmd_addr(priv, flash, cmdbuf, cmdlen - (flash->spi->read_dummy/8)); for (i = 0 ; i < (flash->spi->read_dummy/8); i++) aspeed_spi_write_to_ahb(flash->ahb_base, &dummy, 1); if (flash->iomode) { clrbits_le32(&priv->regs->ce_ctrl[flash->cs], CE_CTRL_IO_MODE_MASK); setbits_le32(&priv->regs->ce_ctrl[flash->cs], flash->iomode); } aspeed_spi_read_from_ahb(flash->ahb_base, read_buf, len); aspeed_spi_stop_user(priv, flash); return 0; } static ssize_t aspeed_spi_write_user(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, unsigned int cmdlen, const u8 *cmdbuf, unsigned int len, const u8 *write_buf) { aspeed_spi_start_user(priv, flash); /* cmd buffer = cmd + addr */ aspeed_spi_send_cmd_addr(priv, flash, cmdbuf, cmdlen); aspeed_spi_write_to_ahb(flash->ahb_base, write_buf, len); aspeed_spi_stop_user(priv, flash); return 0; } static u32 aspeed_spi_flash_to_addr(struct aspeed_spi_flash *flash, const u8 *cmdbuf, unsigned int cmdlen) { u8 addrlen = cmdlen - 1; u32 addr = (cmdbuf[1] << 16) | (cmdbuf[2] << 8) | cmdbuf[3]; /* * U-Boot SPI Flash layer uses 3 bytes addresses, but it might * change one day */ if (addrlen == 4) addr = (addr << 8) | cmdbuf[4]; return addr; } /* TODO(clg@kaod.org): add support for XFER_MMAP instead ? */ static ssize_t aspeed_spi_read(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, unsigned int cmdlen, const u8 *cmdbuf, unsigned int len, u8 *read_buf) { /* cmd buffer = cmd + addr + dummies */ u32 offset = aspeed_spi_flash_to_addr(flash, cmdbuf, cmdlen - (flash->spi->read_dummy/8)); /* * Switch to USER command mode if the AHB window configured * for the device is too small for the read operation */ if (offset + len >= flash->ahb_size) { return aspeed_spi_read_user(priv, flash, cmdlen, cmdbuf, len, read_buf); } memcpy_fromio(read_buf, flash->ahb_base + offset, len); return 0; } static int aspeed_spi_xfer(struct udevice *dev, unsigned int bitlen, const void *dout, void *din, unsigned long flags) { struct udevice *bus = dev->parent; struct aspeed_spi_priv *priv = dev_get_priv(bus); struct aspeed_spi_flash *flash; u8 *cmd_buf = priv->cmd_buf; size_t data_bytes; int err = 0; flash = aspeed_spi_get_flash(dev); if (!flash) return -ENXIO; if (flags & SPI_XFER_BEGIN) { /* save command in progress */ priv->cmd_len = bitlen / 8; memcpy(cmd_buf, dout, priv->cmd_len); } if (flags == (SPI_XFER_BEGIN | SPI_XFER_END)) { /* if start and end bit are set, the data bytes is 0. */ data_bytes = 0; } else { data_bytes = bitlen / 8; } debug("CS%u: %s cmd %zu bytes data %zu bytes\n", flash->cs, din ? "read" : "write", priv->cmd_len, data_bytes); if ((flags & SPI_XFER_END) || flags == 0) { if (priv->cmd_len == 0) { pr_err("No command is progress !\n"); return -1; } if (din && data_bytes) { if (priv->cmd_len == 1) err = aspeed_spi_read_reg(priv, flash, cmd_buf[0], din, data_bytes); else err = aspeed_spi_read(priv, flash, priv->cmd_len, cmd_buf, data_bytes, din); } else if (dout) { if (priv->cmd_len == 1) err = aspeed_spi_write_reg(priv, flash, cmd_buf[0], dout, data_bytes); else err = aspeed_spi_write_user(priv, flash, priv->cmd_len, cmd_buf, data_bytes, dout); } if (flags & SPI_XFER_END) { /* clear command */ memset(cmd_buf, 0, sizeof(priv->cmd_buf)); priv->cmd_len = 0; } } return err; } static int aspeed_spi_child_pre_probe(struct udevice *dev) { struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); debug("pre_probe slave device on CS%u, max_hz %u, mode 0x%x.\n", slave_plat->cs, slave_plat->max_hz, slave_plat->mode); if (!aspeed_spi_get_flash(dev)) return -ENXIO; return 0; } /* * It is possible to automatically define a contiguous address space * on top of all CEs in the AHB window of the controller but it would * require much more work. Let's start with a simple mapping scheme * which should work fine for a single flash device. * * More complex schemes should probably be defined with the device * tree. */ static int aspeed_spi_flash_set_segment(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash) { u32 seg_addr; /* could be configured through the device tree */ flash->ahb_size = flash->spi->size; if (priv->new_ver) { seg_addr = G6_SEGMENT_ADDR_VALUE((u32)flash->ahb_base, (u32)flash->ahb_base + flash->ahb_size); } else { seg_addr = SEGMENT_ADDR_VALUE((u32)flash->ahb_base, (u32)flash->ahb_base + flash->ahb_size); } writel(seg_addr, &priv->regs->segment_addr[flash->cs]); return 0; } static int aspeed_spi_flash_init(struct aspeed_spi_priv *priv, struct aspeed_spi_flash *flash, struct udevice *dev) { struct spi_flash *spi_flash = dev_get_uclass_priv(dev); struct spi_slave *slave = dev_get_parent_priv(dev); u32 read_hclk; /* * The SPI flash device slave should not change, so initialize * it only once. */ if (flash->init) return 0; /* * The flash device has not been probed yet. Initial transfers * to read the JEDEC of the device will use the initial * default settings of the registers. */ if (!spi_flash->name) return 0; debug("CS%u: init %s flags:%x size:%d page:%d sector:%d erase:%d " "cmds [ erase:%x read=%x write:%x ] dummy:%d\n", flash->cs, spi_flash->name, spi_flash->flags, spi_flash->size, spi_flash->page_size, spi_flash->sector_size, spi_flash->erase_size, spi_flash->erase_opcode, spi_flash->read_opcode, spi_flash->program_opcode, spi_flash->read_dummy); flash->spi = spi_flash; flash->ce_ctrl_user = CE_CTRL_USERMODE; if(priv->new_ver) read_hclk = aspeed_g6_spi_hclk_divisor(priv, slave->speed); else read_hclk = aspeed_spi_hclk_divisor(priv, slave->speed); if (slave->mode & (SPI_RX_DUAL | SPI_TX_DUAL)) { debug("CS%u: setting dual data mode\n", flash->cs); flash->iomode = CE_CTRL_IO_DUAL_DATA; flash->spi->read_opcode = SPINOR_OP_READ_1_1_2; } else if (slave->mode & (SPI_RX_QUAD | SPI_TX_QUAD)) { flash->iomode = CE_CTRL_IO_QUAD_DATA; flash->spi->read_opcode = SPINOR_OP_READ_1_4_4; } else { debug("normal read \n"); } if(priv->new_ver) { flash->ce_ctrl_fread = CE_G6_CTRL_CLOCK_FREQ(read_hclk) | flash->iomode | CE_CTRL_CMD(flash->spi->read_opcode) | CE_CTRL_DUMMY((flash->spi->read_dummy/8)) | CE_CTRL_FREADMODE; } else { flash->ce_ctrl_fread = CE_CTRL_CLOCK_FREQ(read_hclk) | flash->iomode | CE_CTRL_CMD(flash->spi->read_opcode) | CE_CTRL_DUMMY((flash->spi->read_dummy/8)) | CE_CTRL_FREADMODE; } debug("CS%u: USER mode 0x%08x FREAD mode 0x%08x\n", flash->cs, flash->ce_ctrl_user, flash->ce_ctrl_fread); /* Set the CE Control Register default (FAST READ) */ writel(flash->ce_ctrl_fread, &priv->regs->ce_ctrl[flash->cs]); /* Set Address Segment Register for direct AHB accesses */ aspeed_spi_flash_set_segment(priv, flash); /* All done */ flash->init = true; return 0; } static int aspeed_spi_claim_bus(struct udevice *dev) { struct udevice *bus = dev->parent; struct aspeed_spi_priv *priv = dev_get_priv(bus); struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); struct aspeed_spi_flash *flash; debug("%s: claim bus CS%u\n", bus->name, slave_plat->cs); flash = aspeed_spi_get_flash(dev); if (!flash) return -ENODEV; return aspeed_spi_flash_init(priv, flash, dev); } static int aspeed_spi_release_bus(struct udevice *dev) { struct udevice *bus = dev->parent; struct dm_spi_slave_platdata *slave_plat = dev_get_parent_platdata(dev); debug("%s: release bus CS%u\n", bus->name, slave_plat->cs); if (!aspeed_spi_get_flash(dev)) return -ENODEV; return 0; } static int aspeed_spi_set_mode(struct udevice *bus, uint mode) { debug("%s: setting mode to %x\n", bus->name, mode); if (mode & (SPI_RX_QUAD | SPI_TX_QUAD)) { pr_err("%s invalid QUAD IO mode\n", bus->name); return -EINVAL; } /* The CE Control Register is set in claim_bus() */ return 0; } static int aspeed_spi_set_speed(struct udevice *bus, uint hz) { debug("%s: setting speed to %u\n", bus->name, hz); /* The CE Control Register is set in claim_bus() */ return 0; } static int aspeed_spi_count_flash_devices(struct udevice *bus) { ofnode node; int count = 0; dev_for_each_subnode(node, bus) { if (ofnode_is_available(node) && ofnode_device_is_compatible(node, "spi-flash")) count++; } return count; } static int aspeed_spi_bind(struct udevice *bus) { debug("%s assigned req_seq=%d seq=%d\n", bus->name, bus->req_seq, bus->seq); return 0; } static int aspeed_spi_probe(struct udevice *bus) { struct resource res_regs, res_ahb; struct aspeed_spi_priv *priv = dev_get_priv(bus); struct clk hclk; int ret; ret = dev_read_resource(bus, 0, &res_regs); if (ret < 0) return ret; priv->regs = (void __iomem *)res_regs.start; ret = dev_read_resource(bus, 1, &res_ahb); if (ret < 0) return ret; priv->ahb_base = (void __iomem *)res_ahb.start; priv->ahb_size = res_ahb.end - res_ahb.start; ret = clk_get_by_index(bus, 0, &hclk); if (ret < 0) { pr_err("%s could not get clock: %d\n", bus->name, ret); return ret; } priv->hclk_rate = clk_get_rate(&hclk); clk_free(&hclk); priv->max_hz = dev_read_u32_default(bus, "spi-max-frequency", 100000000); priv->num_cs = dev_read_u32_default(bus, "num-cs", ASPEED_SPI_MAX_CS); priv->flash_count = aspeed_spi_count_flash_devices(bus); if (priv->flash_count > priv->num_cs) { pr_err("%s has too many flash devices: %d\n", bus->name, priv->flash_count); return -EINVAL; } if (!priv->flash_count) { pr_err("%s has no flash devices ?!\n", bus->name); return -ENODEV; } if (device_is_compatible(bus, "aspeed,ast2600-fmc") || device_is_compatible(bus, "aspeed,ast2600-fmc")) { priv->new_ver = 1; } /* * There are some slight differences between the FMC and the * SPI controllers */ priv->is_fmc = dev_get_driver_data(bus); ret = aspeed_spi_controller_init(priv); if (ret) return ret; debug("%s probed regs=%p ahb_base=%p max-hz=%d cs=%d seq=%d\n", bus->name, priv->regs, priv->ahb_base, priv->max_hz, priv->flash_count, bus->seq); return 0; } static const struct dm_spi_ops aspeed_spi_ops = { .claim_bus = aspeed_spi_claim_bus, .release_bus = aspeed_spi_release_bus, .set_mode = aspeed_spi_set_mode, .set_speed = aspeed_spi_set_speed, .xfer = aspeed_spi_xfer, }; static const struct udevice_id aspeed_spi_ids[] = { { .compatible = "aspeed,ast2600-fmc", .data = 1 }, { .compatible = "aspeed,ast2600-spi", .data = 0 }, { .compatible = "aspeed,ast2500-fmc", .data = 1 }, { .compatible = "aspeed,ast2500-spi", .data = 0 }, { } }; U_BOOT_DRIVER(aspeed_spi) = { .name = "aspeed_spi", .id = UCLASS_SPI, .of_match = aspeed_spi_ids, .ops = &aspeed_spi_ops, .priv_auto_alloc_size = sizeof(struct aspeed_spi_priv), .child_pre_probe = aspeed_spi_child_pre_probe, .bind = aspeed_spi_bind, .probe = aspeed_spi_probe, };