// SPDX-License-Identifier: GPL-2.0 /* * Copyright (C) ASPEED Technology Inc. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "sdram_phy_ast2600.h" /* in order to speed up DRAM init time, write pre-defined values to registers * directly */ #define AST2600_SDRAMMC_MANUAL_CLK /* register offset */ #define AST_SCU_FPGA_STATUS 0x004 #define AST_SCU_HANDSHAKE 0x100 #define AST_SCU_MPLL 0x220 #define AST_SCU_MPLL_EXT 0x224 #define AST_SCU_FPGA_PLL 0x400 #define AST_SCU_HW_STRAP 0x500 #define AST_SCU_EFUSE_DATA 0x594 /* bit-field of AST_SCU_HW_STRAP */ #define SCU_HWSTRAP_VGAMEM_SHIFT 13 #define SCU_HWSTRAP_VGAMEM_MASK GENMASK(14, 13) /* bit-field of AST_SCU_EFUSE_DATA */ #define SCU_EFUSE_DATA_VGA_DIS_MASK BIT(14) /* bit-field of AST_SCU_HANDSHAKE */ #define SCU_SDRAM_SUPPORT_IKVM_HIGH_RES BIT(0) #define SCU_SDRAM_INIT_READY_MASK BIT(6) #define SCU_SDRAM_INIT_BY_SOC_MASK BIT(7) #define SCU_P2A_BRIDGE_DISABLE BIT(12) #define SCU_HANDSHAKE_MASK \ (SCU_SDRAM_INIT_READY_MASK | SCU_SDRAM_INIT_BY_SOC_MASK | \ SCU_P2A_BRIDGE_DISABLE | SCU_SDRAM_SUPPORT_IKVM_HIGH_RES) /* bit-field of AST_SCU_MPLL */ #define SCU_MPLL_RESET BIT(25) #define SCU_MPLL_BYPASS BIT(24) #define SCU_MPLL_TURN_OFF BIT(23) #define SCU_MPLL_FREQ_MASK GENMASK(22, 0) #define SCU_MPLL_FREQ_400M 0x0008405F #define SCU_MPLL_EXT_400M 0x0000002F //#define SCU_MPLL_FREQ_400M 0x0038007F //#define SCU_MPLL_EXT_400M 0x0000003F #define SCU_MPLL_FREQ_333M 0x00488299 #define SCU_MPLL_EXT_333M 0x0000014C #define SCU_MPLL_FREQ_200M 0x0078007F #define SCU_MPLL_EXT_200M 0x0000003F #define SCU_MPLL_FREQ_100M 0x0078003F #define SCU_MPLL_EXT_100M 0x0000001F /* MPLL configuration */ #if defined(CONFIG_ASPEED_DDR4_1600) #define SCU_MPLL_FREQ_CFG SCU_MPLL_FREQ_400M #define SCU_MPLL_EXT_CFG SCU_MPLL_EXT_400M #elif defined(CONFIG_ASPEED_DDR4_1333) #define SCU_MPLL_FREQ_CFG SCU_MPLL_FREQ_333M #define SCU_MPLL_EXT_CFG SCU_MPLL_EXT_333M #elif defined(CONFIG_ASPEED_DDR4_800) #define SCU_MPLL_FREQ_CFG SCU_MPLL_FREQ_200M #define SCU_MPLL_EXT_CFG SCU_MPLL_EXT_200M #elif defined(CONFIG_ASPEED_DDR4_400) #define SCU_MPLL_FREQ_CFG SCU_MPLL_FREQ_100M #define SCU_MPLL_EXT_CFG SCU_MPLL_EXT_100M #else #error "undefined DDR4 target rate\n" #endif /** * MR01[26:24] - ODT configuration (DRAM side) * b'001 : 60 ohm * b'101 : 48 ohm * b'011 : 40 ohm (default) */ #if defined(CONFIG_ASPEED_DDR4_DRAM_ODT60) #define MR01_DRAM_ODT (0x1 << 24) #elif defined(CONFIG_ASPEED_DDR4_DRAM_ODT48) #define MR01_DRAM_ODT (0x5 << 24) #else #define MR01_DRAM_ODT (0x3 << 24) #endif /* AC timing and SDRAM mode registers */ #if defined(CONFIG_FPGA_ASPEED) || defined(CONFIG_ASPEED_PALLADIUM) /* mode register settings for FPGA are fixed */ #define DDR4_MR01_MODE (MR01_DRAM_ODT | 0x00010100) #define DDR4_MR23_MODE 0x00000000 #define DDR4_MR45_MODE 0x04C00000 #define DDR4_MR6_MODE 0x00000050 #define DDR4_TRFC_FPGA 0x17263434 #define DDR4_TRFI 0x5d /* FPGA need for an additional initialization procedure: search read window */ #define SEARCH_RDWIN_ANCHOR_0 (CONFIG_SYS_SDRAM_BASE + 0x0000) #define SEARCH_RDWIN_ANCHOR_1 (CONFIG_SYS_SDRAM_BASE + 0x0004) #define SEARCH_RDWIN_PTRN_0 0x12345678 #define SEARCH_RDWIN_PTRN_1 0xaabbccdd #define SEARCH_RDWIN_PTRN_SUM 0xbcf02355 #else /* mode register setting for real chip are derived from the model GDDR4-1600 */ #define DDR4_MR01_MODE ((MR1_VAL << 16) | MR0_VAL) #define DDR4_MR23_MODE ((MR3_VAL << 16) | MR2_VAL) #define DDR4_MR45_MODE ((MR5_VAL << 16) | MR4_VAL) #define DDR4_MR6_MODE MR6_VAL #define DDR4_TRFC_1600 0x467299f1 #define DDR4_TRFC_1333 0x3a5f80c9 #define DDR4_TRFC_800 0x23394c78 #define DDR4_TRFC_400 0x111c263c /* * tRFI calculation * DDR4 spec. : * tRFI = 7.8 us if temperature is Less/equal than 85 degree celsius * tRFI = 3.9 us if temperature is greater than 85 degree celsius * * tRFI in MCR0C = floor(tRFI * 12.5M) - margin * normal temp. -> floor(7.8 * 12.5) - 2 = 0x5f * high temp. -> floor(3.9 * 12.5) - 1 = 0x2f */ #ifdef CONFIG_ASPEED_HI_TEMP_TRFI #define DDR4_TRFI 0x2f /* High temperature tRFI */ #else #define DDR4_TRFI 0x5f /* Normal temperature tRFI */ #endif /* end of "#ifdef CONFIG_ASPEED_HI_TEMP_TRFI" */ #endif /* end of "#if defined(CONFIG_FPGA_ASPEED) || \ defined(CONFIG_ASPEED_PALLADIUM)" */ #if defined(CONFIG_FPGA_ASPEED) || defined(CONFIG_ASPEED_PALLADIUM) #define DDR4_TRFC DDR4_TRFC_FPGA #else /* real chip setting */ #if defined(CONFIG_ASPEED_DDR4_1600) #define DDR4_TRFC DDR4_TRFC_1600 #define DDR4_PHY_TRAIN_TRFC 0xc30 #elif defined(CONFIG_ASPEED_DDR4_1333) #define DDR4_TRFC DDR4_TRFC_1333 #define DDR4_PHY_TRAIN_TRFC 0xa25 #elif defined(CONFIG_ASPEED_DDR4_800) #define DDR4_TRFC DDR4_TRFC_800 #define DDR4_PHY_TRAIN_TRFC 0x618 #elif defined(CONFIG_ASPEED_DDR4_400) #define DDR4_TRFC DDR4_TRFC_400 #define DDR4_PHY_TRAIN_TRFC 0x30c #else #error "undefined tRFC setting" #endif /* end of "#if (SCU_MPLL_FREQ_CFG == SCU_MPLL_FREQ_400M)" */ #endif /* end of "#if defined(CONFIG_FPGA_ASPEED) || \ defined(CONFIG_ASPEED_PALLADIUM)" */ /* supported SDRAM size */ #define SDRAM_SIZE_1KB (1024U) #define SDRAM_SIZE_1MB (SDRAM_SIZE_1KB * SDRAM_SIZE_1KB) #define SDRAM_MIN_SIZE (256 * SDRAM_SIZE_1MB) #define SDRAM_MAX_SIZE (2048 * SDRAM_SIZE_1MB) DECLARE_GLOBAL_DATA_PTR; /* * Bandwidth configuration parameters for different SDRAM requests. * These are hardcoded settings taken from Aspeed SDK. */ #if defined(CONFIG_FPGA_ASPEED) || defined(CONFIG_ASPEED_PALLADIUM) static const u32 ddr4_ac_timing[4] = { 0x030C0207, 0x04451133, 0x0E010200, 0x00000140 }; static const u32 ddr_max_grant_params[4] = { 0x88888888, 0x88888888, 0x88888888, 0x88888888 }; #else static const u32 ddr4_ac_timing[4] = { 0x040e0307, 0x0f4711f1, 0x0e060304, 0x00001240 }; static const u32 ddr_max_grant_params[4] = { 0x44484488, 0xee4444ee, 0x44444444, 0x44444444 }; #endif struct dram_info { struct ram_info info; struct clk ddr_clk; struct ast2600_sdrammc_regs *regs; void __iomem *scu; struct ast2600_ddr_phy *phy; void __iomem *phy_setting; void __iomem *phy_status; ulong clock_rate; }; static void ast2600_sdramphy_kick_training(struct dram_info *info) { #if !defined(CONFIG_FPGA_ASPEED) && !defined(CONFIG_ASPEED_PALLADIUM) struct ast2600_sdrammc_regs *regs = info->regs; u32 volatile data; writel(SDRAM_PHYCTRL0_NRST, ®s->phy_ctrl[0]); udelay(5); writel(SDRAM_PHYCTRL0_NRST | SDRAM_PHYCTRL0_INIT, ®s->phy_ctrl[0]); udelay(1000); while (1) { data = readl(®s->phy_ctrl[0]) & SDRAM_PHYCTRL0_INIT; if (data == 0) break; } #endif } /** * @brief load DDR-PHY configurations table to the PHY registers * @param[in] p_tbl - pointer to the configuration table * @param[in] info - pointer to the DRAM info struct * * There are two sets of MRS (Mode Registers) configuration in ast2600 memory * system: one is in the SDRAM MC (memory controller) which is used in run * time, and the other is in the DDR-PHY IP which is used during DDR-PHY * training. */ static void ast2600_sdramphy_init(u32 *p_tbl, struct dram_info *info) { #if !defined(CONFIG_FPGA_ASPEED) && !defined(CONFIG_ASPEED_PALLADIUM) u32 reg_base = (u32)info->phy_setting; u32 addr = p_tbl[0]; u32 data; int i = 1; writel(0, &info->regs->phy_ctrl[0]); udelay(10); //writel(SDRAM_PHYCTRL0_NRST, ®s->phy_ctrl[0]); /* load PHY configuration table into PHY-setting registers */ while (1) { if (addr < reg_base) { debug("invalid DDR-PHY addr: 0x%08x\n", addr); break; } data = p_tbl[i++]; if (data == DDR_PHY_TBL_END) { break; } else if (data == DDR_PHY_TBL_CHG_ADDR) { addr = p_tbl[i++]; } else { writel(data, addr); addr += 4; } } data = readl(info->phy_setting + 0x84) & ~GENMASK(16, 0); data |= DDR4_PHY_TRAIN_TRFC; writel(data, info->phy_setting + 0x84); #endif } static int ast2600_sdramphy_check_status(struct dram_info *info) { #if !defined(CONFIG_FPGA_ASPEED) && !defined(CONFIG_ASPEED_PALLADIUM) u32 value, tmp; u32 reg_base = (u32)info->phy_status; int need_retrain = 0; debug("\nSDRAM PHY training report:\n"); /* training status */ value = readl(reg_base + 0x00); debug("\nrO_DDRPHY_reg offset 0x00 = 0x%08x\n", value); if (value & BIT(3)) debug("\tinitial PVT calibration fail\n"); if (value & BIT(5)) debug("\truntime calibration fail\n"); /* PU & PD */ value = readl(reg_base + 0x30); debug("\nrO_DDRPHY_reg offset 0x30 = 0x%08x\n", value); debug(" PU = 0x%02lx\n", FIELD_GET(GENMASK(7, 0), value)); debug(" PD = 0x%02lx\n", FIELD_GET(GENMASK(23, 16), value)); /* read eye window */ value = readl(reg_base + 0x68); if (FIELD_GET(GENMASK(7, 0), value) == 0) need_retrain = 1; debug("\nrO_DDRPHY_reg offset 0x68 = 0x%08x\n", value); debug(" rising edge of read data eye training pass window\n"); tmp = FIELD_GET(GENMASK(7, 0), value) * 100 / 255; debug(" B0:%d%%\n", tmp); tmp = FIELD_GET(GENMASK(15, 8), value) * 100 / 255; debug(" B1:%d%%\n", tmp); value = readl(reg_base + 0xC8); debug("\nrO_DDRPHY_reg offset 0xC8 = 0x%08x\n", value); debug(" falling edge of read data eye training pass window\n"); tmp = FIELD_GET(GENMASK(7, 0), value) * 100 / 255; debug(" B0:%d%%\n", tmp); tmp = FIELD_GET(GENMASK(15, 8), value) * 100 / 255; debug(" B1:%d%%\n", tmp); /* write eye window */ value = readl(reg_base + 0x7c); if (FIELD_GET(GENMASK(7, 0), value) == 0) need_retrain = 1; debug("\nrO_DDRPHY_reg offset 0x7C = 0x%08x\n", value); debug(" write data eye training pass window\n"); tmp = FIELD_GET(GENMASK(7, 0), value) * 100 / 255; debug(" B0:%d%%\n", tmp); tmp = FIELD_GET(GENMASK(15, 8), value) * 100 / 255; debug(" B1:%d%%\n", tmp); /* read Vref (PHY side) training result */ value = readl(reg_base + 0x88); debug("\nrO_DDRPHY_reg offset 0x88 = 0x%08x\n", value); debug(" Read VrefDQ training result\n"); tmp = FIELD_GET(GENMASK(7, 0), value) * 10000 / 128; debug(" B0:%d.%d%%\n", tmp / 100, tmp % 100); tmp = FIELD_GET(GENMASK(15, 8), value) * 10000 / 128; debug(" B1:%d.%d%%\n", tmp / 100, tmp % 100); /* write Vref (DRAM side) training result */ value = readl(reg_base + 0x90); debug("\nrO_DDRPHY_reg offset 0x90 = 0x%08x\n", value); tmp = readl(info->phy_setting + 0x60) & BIT(6); if (tmp) { value = 4500 + 65 * value; debug(" Write Vref training result: %d.%d%% (range 2)\n", value / 100, value % 100); } else { value = 6000 + 65 * value; debug(" Write Vref training result: %d.%d%% (range 1)\n", value / 100, value % 100); } /* gate train */ value = readl(reg_base + 0x50); debug("\nrO_DDRPHY_reg offset 0x50 = 0x%08x\n", value); if ((FIELD_GET(GENMASK(15, 0), value) == 0) || (FIELD_GET(GENMASK(31, 16), value) == 0)) need_retrain = 1; debug(" gate training pass window\n"); debug(" module 0: 0x%04lx\n", FIELD_GET(GENMASK(15, 0), value)); debug(" module 1: 0x%04lx\n", FIELD_GET(GENMASK(31, 16), value)); return need_retrain; #else return 0; #endif } #ifndef CONFIG_ASPEED_BYPASS_SELFTEST #define MC_TEST_PATTERN_N 8 static u32 as2600_sdrammc_test_pattern[MC_TEST_PATTERN_N] = { 0xcc33cc33, 0xff00ff00, 0xaa55aa55, 0x88778877, 0x92cc4d6e, 0x543d3cde, 0xf1e843c7, 0x7c61d253 }; #define TIMEOUT_DRAM 5000000 int ast2600_sdrammc_dg_test(struct dram_info *info, unsigned int datagen, u32 mode) { unsigned int data; unsigned int timeout = 0; struct ast2600_sdrammc_regs *regs = info->regs; writel(0, ®s->ecc_test_ctrl); if (mode == 0) writel(0x00000085 | (datagen << 3), ®s->ecc_test_ctrl); else writel(0x000000C1 | (datagen << 3), ®s->ecc_test_ctrl); do { data = readl(®s->ecc_test_ctrl) & GENMASK(13, 12); if (data & BIT(13)) return 0; if (++timeout > TIMEOUT_DRAM) { printf("Timeout!!\n"); writel(0, ®s->ecc_test_ctrl); return 0; } } while (!data); writel(0, ®s->ecc_test_ctrl); return 1; } int ast2600_sdrammc_cbr_test(struct dram_info *info) { struct ast2600_sdrammc_regs *regs = info->regs; u32 i; clrsetbits_le32(®s->test_addr, GENMASK(30, 4), 0x7ffff0); /* single */ for (i = 0; i < 8; i++) { if (!ast2600_sdrammc_dg_test(info, i, 0)) return (0); } /* burst */ for (i = 0; i < 8; i++) { if (!ast2600_sdrammc_dg_test(info, i, i)) return (0); } return(1); } static int ast2600_sdrammc_test(struct dram_info *info) { struct ast2600_sdrammc_regs *regs = info->regs; u32 pass_cnt = 0; u32 fail_cnt = 0; u32 target_cnt = 2; u32 test_cnt = 0; u32 pattern; u32 i = 0; bool finish = false; debug("sdram mc test:\n"); while (finish == false) { pattern = as2600_sdrammc_test_pattern[i++]; i = i % MC_TEST_PATTERN_N; debug(" pattern = %08x : ", pattern); writel(pattern, ®s->test_init_val); if (!ast2600_sdrammc_cbr_test(info)) { debug("fail\n"); fail_cnt++; } else { debug("pass\n"); pass_cnt++; } if (++test_cnt == target_cnt) { finish = true; } } debug("statistics: pass/fail/total:%d/%d/%d\n", pass_cnt, fail_cnt, target_cnt); return fail_cnt; } #endif /** * scu500[14:13] * 2b'00: VGA memory size = 16MB * 2b'01: VGA memory size = 16MB * 2b'10: VGA memory size = 32MB * 2b'11: VGA memory size = 64MB * * mcr04[3:2] * 2b'00: VGA memory size = 8MB * 2b'01: VGA memory size = 16MB * 2b'10: VGA memory size = 32MB * 2b'11: VGA memory size = 64MB */ static size_t ast2600_sdrammc_get_vga_mem_size(struct dram_info *info) { u32 vga_hwconf; size_t vga_mem_size_base = 8 * 1024 * 1024; vga_hwconf = (readl(info->scu + AST_SCU_HW_STRAP) & SCU_HWSTRAP_VGAMEM_MASK) >> SCU_HWSTRAP_VGAMEM_SHIFT; if (vga_hwconf == 0) { vga_hwconf = 1; writel(vga_hwconf << SCU_HWSTRAP_VGAMEM_SHIFT, info->scu + AST_SCU_HW_STRAP); } clrsetbits_le32(&info->regs->config, SDRAM_CONF_VGA_SIZE_MASK, ((vga_hwconf << SDRAM_CONF_VGA_SIZE_SHIFT) & SDRAM_CONF_VGA_SIZE_MASK)); /* no need to reserve VGA memory if efuse[VGA disable] is set */ if (readl(info->scu + AST_SCU_EFUSE_DATA) & SCU_EFUSE_DATA_VGA_DIS_MASK) return 0; return vga_mem_size_base << vga_hwconf; } #if defined(CONFIG_FPGA_ASPEED) || defined(CONFIG_ASPEED_PALLADIUM) static void ast2600_sdrammc_fpga_set_pll(struct dram_info *info) { u32 data; u32 scu_base = (u32)info->scu; writel(0x00000303, scu_base + AST_SCU_FPGA_PLL); do { data = readl(scu_base + AST_SCU_FPGA_STATUS); } while (!(data & 0x100)); writel(0x00000103, scu_base + AST_SCU_FPGA_PLL); } static int ast2600_sdrammc_search_read_window(struct dram_info *info) { u32 pll, pll_min, pll_max, dat1, offset; u32 win = 0x03, gwin = 0, gwinsize = 0; u32 phy_setting = (u32)info->phy_setting; #ifdef CONFIG_ASPEED_PALLADIUM writel(0xc, phy_setting + 0x0000); return 1; #endif writel(SEARCH_RDWIN_PTRN_0, SEARCH_RDWIN_ANCHOR_0); writel(SEARCH_RDWIN_PTRN_1, SEARCH_RDWIN_ANCHOR_1); while (gwin == 0) { while (!(win & 0x80)) { debug("Window = 0x%X\n", win); writel(win, phy_setting + 0x0000); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); while (dat1 == SEARCH_RDWIN_PTRN_SUM) { ast2600_sdrammc_fpga_set_pll(info); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); } pll_min = 0xfff; pll_max = 0x0; pll = 0; while (pll_max > 0 || pll < 256) { ast2600_sdrammc_fpga_set_pll(info); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); if (dat1 == SEARCH_RDWIN_PTRN_SUM) { if (pll_min > pll) pll_min = pll; if (pll_max < pll) pll_max = pll; debug("%3d_(%3d:%3d)\n", pll, pll_min, pll_max); } else if (pll_max > 0) { pll_min = pll_max - pll_min; if (gwinsize < pll_min) { gwin = win; gwinsize = pll_min; } break; } pll += 1; } if (gwin != 0 && pll_max == 0) break; win = win << 1; } if (gwin == 0) win = 0x7; } debug("Set PLL Read Gating Window = %x\n", gwin); writel(gwin, phy_setting + 0x0000); debug("PLL Read Window training\n"); pll_min = 0xfff; pll_max = 0x0; debug("Search Window Start\n"); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); while (dat1 == SEARCH_RDWIN_PTRN_SUM) { ast2600_sdrammc_fpga_set_pll(info); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); } debug("Search Window Margin\n"); pll = 0; while (pll_max > 0 || pll < 256) { ast2600_sdrammc_fpga_set_pll(info); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); if (dat1 == SEARCH_RDWIN_PTRN_SUM) { if (pll_min > pll) pll_min = pll; if (pll_max < pll) pll_max = pll; debug("%3d_(%3d:%3d)\n", pll, pll_min, pll_max); } else if (pll_max > 0 && (pll_max - pll_min) > 20) { break; } else if (pll_max > 0) { pll_min = 0xfff; pll_max = 0x0; } pll += 1; } if (pll_min < pll_max) { debug("PLL Read window = %d\n", (pll_max - pll_min)); offset = (pll_max - pll_min) >> 1; pll_min = 0xfff; pll = 0; while (pll < (pll_min + offset)) { ast2600_sdrammc_fpga_set_pll(info); dat1 = readl(SEARCH_RDWIN_ANCHOR_0); dat1 += readl(SEARCH_RDWIN_ANCHOR_1); if (dat1 == SEARCH_RDWIN_PTRN_SUM) { if (pll_min > pll) { pll_min = pll; } debug("%d\n", pll); } else { pll_min = 0xfff; pll_max = 0x0; } pll += 1; } return (1); } else { debug("PLL Read window training fail\n"); return 0; } } #endif /* end of "#if defined(CONFIG_FPGA_ASPEED) || \ defined(CONFIG_ASPEED_PALLADIUM)" */ /* * Find out RAM size and save it in dram_info * * The procedure is taken from Aspeed SDK */ static void ast2600_sdrammc_calc_size(struct dram_info *info) { /* The controller supports 256/512/1024/2048 MB ram */ size_t ram_size = SDRAM_MIN_SIZE; const int write_test_offset = 0x100000; u32 test_pattern = 0xdeadbeef; u32 cap_param = SDRAM_CONF_CAP_2048M; u32 refresh_timing_param = DDR4_TRFC; const u32 write_addr_base = CONFIG_SYS_SDRAM_BASE + write_test_offset; for (ram_size = SDRAM_MAX_SIZE; ram_size > SDRAM_MIN_SIZE; ram_size >>= 1) { writel(test_pattern, write_addr_base + (ram_size >> 1)); test_pattern = (test_pattern >> 4) | (test_pattern << 28); } /* One last write to overwrite all wrapped values */ writel(test_pattern, write_addr_base); /* Reset the pattern and see which value was really written */ test_pattern = 0xdeadbeef; for (ram_size = SDRAM_MAX_SIZE; ram_size > SDRAM_MIN_SIZE; ram_size >>= 1) { if (readl(write_addr_base + (ram_size >> 1)) == test_pattern) break; --cap_param; refresh_timing_param >>= 8; test_pattern = (test_pattern >> 4) | (test_pattern << 28); } clrsetbits_le32(&info->regs->ac_timing[1], (SDRAM_AC_TRFC_MASK << SDRAM_AC_TRFC_SHIFT), ((refresh_timing_param & SDRAM_AC_TRFC_MASK) << SDRAM_AC_TRFC_SHIFT)); info->info.base = CONFIG_SYS_SDRAM_BASE; info->info.size = ram_size - ast2600_sdrammc_get_vga_mem_size(info) - CONFIG_ASPEED_SSP_RERV_MEM; clrsetbits_le32( &info->regs->config, SDRAM_CONF_CAP_MASK, ((cap_param << SDRAM_CONF_CAP_SHIFT) & SDRAM_CONF_CAP_MASK)); } static int ast2600_sdrammc_init_ddr4(struct dram_info *info) { const u32 power_ctrl = MCR34_CKE_EN | MCR34_AUTOPWRDN_EN | MCR34_MREQ_BYPASS_DIS | MCR34_RESETN_DIS | MCR34_ODT_EN | MCR34_ODT_AUTO_ON | (0x1 << MCR34_ODT_EXT_SHIFT); /* init SDRAM-PHY only on real chip */ ast2600_sdramphy_init(ast2600_sdramphy_config, info); writel((MCR34_CKE_EN | MCR34_MREQI_DIS | MCR34_RESETN_DIS), &info->regs->power_ctrl); udelay(5); ast2600_sdramphy_kick_training(info); udelay(500); writel(SDRAM_RESET_DLL_ZQCL_EN, &info->regs->refresh_timing); writel(MCR30_SET_MR(3), &info->regs->mode_setting_control); writel(MCR30_SET_MR(6), &info->regs->mode_setting_control); writel(MCR30_SET_MR(5), &info->regs->mode_setting_control); writel(MCR30_SET_MR(4), &info->regs->mode_setting_control); writel(MCR30_SET_MR(2), &info->regs->mode_setting_control); writel(MCR30_SET_MR(1), &info->regs->mode_setting_control); writel(MCR30_SET_MR(0) | MCR30_RESET_DLL_DELAY_EN, &info->regs->mode_setting_control); writel(SDRAM_REFRESH_EN | SDRAM_RESET_DLL_ZQCL_EN | (DDR4_TRFI << SDRAM_REFRESH_PERIOD_SHIFT), &info->regs->refresh_timing); /* wait self-refresh idle */ while (readl(&info->regs->power_ctrl) & MCR34_SELF_REFRESH_STATUS_MASK) ; #if defined(CONFIG_FPGA_ASPEED) || defined(CONFIG_ASPEED_PALLADIUM) writel(SDRAM_REFRESH_EN | SDRAM_LOW_PRI_REFRESH_EN | SDRAM_REFRESH_ZQCS_EN | (DDR4_TRFI << SDRAM_REFRESH_PERIOD_SHIFT) | (0x4000 << SDRAM_REFRESH_PERIOD_ZQCS_SHIFT), &info->regs->refresh_timing); #else writel(SDRAM_REFRESH_EN | SDRAM_LOW_PRI_REFRESH_EN | SDRAM_REFRESH_ZQCS_EN | (DDR4_TRFI << SDRAM_REFRESH_PERIOD_SHIFT) | (0x42aa << SDRAM_REFRESH_PERIOD_ZQCS_SHIFT), &info->regs->refresh_timing); #endif writel(power_ctrl, &info->regs->power_ctrl); udelay(500); #if defined(CONFIG_FPGA_ASPEED) /* toggle Vref training */ setbits_le32(&info->regs->mr6_mode_setting, 0x80); writel(MCR30_RESET_DLL_DELAY_EN | MCR30_SET_MR(6), &info->regs->mode_setting_control); clrbits_le32(&info->regs->mr6_mode_setting, 0x80); writel(MCR30_RESET_DLL_DELAY_EN | MCR30_SET_MR(6), &info->regs->mode_setting_control); #endif return 0; } static void ast2600_sdrammc_unlock(struct dram_info *info) { writel(SDRAM_UNLOCK_KEY, &info->regs->protection_key); while (!readl(&info->regs->protection_key)) ; } static void ast2600_sdrammc_lock(struct dram_info *info) { writel(~SDRAM_UNLOCK_KEY, &info->regs->protection_key); while (readl(&info->regs->protection_key)) ; } static void ast2600_sdrammc_common_init(struct ast2600_sdrammc_regs *regs) { int i; u32 reg; writel(MCR34_MREQI_DIS | MCR34_RESETN_DIS, ®s->power_ctrl); writel(SDRAM_VIDEO_UNLOCK_KEY, ®s->gm_protection_key); /* [6:0] : Group 1 request queued number = 16 * [14:8] : Group 2 request queued number = 16 * [20:16] : R/W max-grant count for RQ output arbitration = 16 */ writel(0x101010, ®s->arbitration_ctrl); /* Request Queued Limitation for REQ8/9 USB1/2 */ writel(0x0FFF3CEF, ®s->req_limit_mask); for (i = 0; i < ARRAY_SIZE(ddr_max_grant_params); ++i) writel(ddr_max_grant_params[i], ®s->max_grant_len[i]); writel(MCR50_RESET_ALL_INTR, ®s->intr_ctrl); /* FIXME: the sample code does NOT match the datasheet */ writel(0x07FFFFFF, ®s->ecc_range_ctrl); writel(0, ®s->ecc_test_ctrl); writel(0x80000001, ®s->test_addr); writel(0, ®s->test_fail_dq_bit); writel(0, ®s->test_init_val); writel(0xFFFFFFFF, ®s->req_input_ctrl); writel(0x300, ®s->req_high_pri_ctrl); udelay(600); #ifdef CONFIG_ASPEED_DDR4_DUALX8 writel(0xa037, ®s->config); #else writel(0xa017, ®s->config); #endif /* load controller setting */ for (i = 0; i < ARRAY_SIZE(ddr4_ac_timing); ++i) writel(ddr4_ac_timing[i], ®s->ac_timing[i]); /* update CL and WL */ reg = readl(®s->ac_timing[1]); reg &= ~(SDRAM_WL_SETTING | SDRAM_CL_SETTING); reg |= FIELD_PREP(SDRAM_WL_SETTING, CONFIG_WL - 5) | FIELD_PREP(SDRAM_CL_SETTING, CONFIG_RL - 5); writel(reg, ®s->ac_timing[1]); writel(DDR4_MR01_MODE, ®s->mr01_mode_setting); writel(DDR4_MR23_MODE, ®s->mr23_mode_setting); writel(DDR4_MR45_MODE, ®s->mr45_mode_setting); writel(DDR4_MR6_MODE, ®s->mr6_mode_setting); } /* * Update size info according to the ECC HW setting * * Assume SDRAM has been initialized by SPL or the host. To get the RAM size, we * don't need to calculate the ECC size again but read from MCR04 and derive the * size from its value. */ static void ast2600_sdrammc_update_size(struct dram_info *info) { struct ast2600_sdrammc_regs *regs = info->regs; size_t hw_size; size_t ram_size = SDRAM_MAX_SIZE; u32 cap_param; cap_param = (readl(&info->regs->config) & SDRAM_CONF_CAP_MASK) >> SDRAM_CONF_CAP_SHIFT; switch (cap_param) { case SDRAM_CONF_CAP_2048M: ram_size = 2048 * SDRAM_SIZE_1MB; break; case SDRAM_CONF_CAP_1024M: ram_size = 1024 * SDRAM_SIZE_1MB; break; case SDRAM_CONF_CAP_512M: ram_size = 512 * SDRAM_SIZE_1MB; break; case SDRAM_CONF_CAP_256M: ram_size = 256 * SDRAM_SIZE_1MB; break; } info->info.base = CONFIG_SYS_SDRAM_BASE; info->info.size = ram_size - ast2600_sdrammc_get_vga_mem_size(info) - CONFIG_ASPEED_SSP_RERV_MEM; if (0 == (readl(®s->config) & SDRAM_CONF_ECC_SETUP)) return; hw_size = readl(®s->ecc_range_ctrl) & GENMASK(30, 20); hw_size += (1 << 20); info->info.size = hw_size; } static void ast2600_sdrammc_ecc_enable(struct dram_info *info, u32 conf_size_mb) { struct ast2600_sdrammc_regs *regs = info->regs; size_t conf_size; u32 reg; conf_size = conf_size_mb * SDRAM_SIZE_1MB; if (conf_size > info->info.size) { printf("warning: ECC configured %dMB but actual size is %dMB\n", conf_size_mb, info->info.size / SDRAM_SIZE_1MB); conf_size = info->info.size; } else if (conf_size == 0) { conf_size = info->info.size; } info->info.size = (((conf_size / 9) * 8) >> 20) << 20; writel(((info->info.size >> 20) - 1) << 20, ®s->ecc_range_ctrl); reg = readl(®s->config) | SDRAM_CONF_ECC_SETUP; writel(reg, ®s->config); writel(0, ®s->test_init_val); writel(0x80000001, ®s->test_addr); writel(0x221, ®s->ecc_test_ctrl); while (0 == (readl(®s->ecc_test_ctrl) & BIT(12))) ; writel(0, ®s->ecc_test_ctrl); writel(BIT(31), ®s->intr_ctrl); writel(0, ®s->intr_ctrl); } static int ast2600_sdrammc_probe(struct udevice *dev) { struct dram_info *priv = (struct dram_info *)dev_get_priv(dev); struct ast2600_sdrammc_regs *regs = priv->regs; struct udevice *clk_dev; int ret; volatile uint32_t reg; /* find SCU base address from clock device */ ret = uclass_get_device_by_driver(UCLASS_CLK, DM_GET_DRIVER(aspeed_scu), &clk_dev); if (ret) { debug("clock device not defined\n"); return ret; } priv->scu = devfdt_get_addr_ptr(clk_dev); if (IS_ERR(priv->scu)) { debug("%s(): can't get SCU\n", __func__); return PTR_ERR(priv->scu); } reg = readl(priv->scu + AST_SCU_HANDSHAKE); if (reg & SCU_SDRAM_INIT_READY_MASK) { printf("already initialized, "); setbits_le32(priv->scu + AST_SCU_HANDSHAKE, SCU_HANDSHAKE_MASK); ast2600_sdrammc_update_size(priv); return 0; } #ifdef AST2600_SDRAMMC_MANUAL_CLK reg = readl(priv->scu + AST_SCU_MPLL); reg &= ~(BIT(24) | GENMASK(22, 0)); reg |= (BIT(25) | SCU_MPLL_FREQ_CFG); writel(reg, priv->scu + AST_SCU_MPLL); writel(SCU_MPLL_EXT_CFG, priv->scu + AST_SCU_MPLL_EXT); udelay(100); reg &= ~BIT(25); writel(reg, priv->scu + AST_SCU_MPLL); while (0 == (readl(priv->scu + AST_SCU_MPLL_EXT) & BIT(31))) ; #else ret = clk_get_by_index(dev, 0, &priv->ddr_clk); if (ret) { debug("DDR:No CLK\n"); return ret; } clk_set_rate(&priv->ddr_clk, priv->clock_rate); #endif #if 0 /* FIXME: enable the following code if reset-driver is ready */ struct reset_ctl reset_ctl; ret = reset_get_by_index(dev, 0, &reset_ctl); if (ret) { debug("%s(): Failed to get reset signal\n", __func__); return ret; } ret = reset_assert(&reset_ctl); if (ret) { debug("%s(): SDRAM reset failed: %u\n", __func__, ret); return ret; } #endif ast2600_sdrammc_unlock(priv); ast2600_sdrammc_common_init(regs); L_ast2600_sdramphy_train: ast2600_sdrammc_init_ddr4(priv); #if defined(CONFIG_FPGA_ASPEED) || defined(CONFIG_ASPEED_PALLADIUM) ast2600_sdrammc_search_read_window(priv); #endif ret = ast2600_sdramphy_check_status(priv); if (ret) { printf("DDR4 PHY training fail, retrain\n"); goto L_ast2600_sdramphy_train; } ast2600_sdrammc_calc_size(priv); #ifndef CONFIG_ASPEED_BYPASS_SELFTEST ret = ast2600_sdrammc_test(priv); if (ret) { printf("%s: DDR4 init fail\n", __func__); return -EINVAL; } #endif if (dev_read_bool(dev, "aspeed,ecc-enabled")) { u32 ecc_size; ecc_size = dev_read_u32_default(dev, "aspeed,ecc-size-mb", 0); ast2600_sdrammc_ecc_enable(priv, ecc_size); } setbits_le32(priv->scu + AST_SCU_HANDSHAKE, SCU_HANDSHAKE_MASK); clrbits_le32(®s->intr_ctrl, MCR50_RESET_ALL_INTR); ast2600_sdrammc_lock(priv); return 0; } static int ast2600_sdrammc_ofdata_to_platdata(struct udevice *dev) { struct dram_info *priv = dev_get_priv(dev); priv->regs = (void *)(uintptr_t)devfdt_get_addr_index(dev, 0); priv->phy_setting = (void *)(uintptr_t)devfdt_get_addr_index(dev, 1); priv->phy_status = (void *)(uintptr_t)devfdt_get_addr_index(dev, 2); priv->clock_rate = fdtdec_get_int(gd->fdt_blob, dev_of_offset(dev), "clock-frequency", 0); if (!priv->clock_rate) { debug("DDR Clock Rate not defined\n"); return -EINVAL; } return 0; } static int ast2600_sdrammc_get_info(struct udevice *dev, struct ram_info *info) { struct dram_info *priv = dev_get_priv(dev); *info = priv->info; return 0; } static struct ram_ops ast2600_sdrammc_ops = { .get_info = ast2600_sdrammc_get_info, }; static const struct udevice_id ast2600_sdrammc_ids[] = { { .compatible = "aspeed,ast2600-sdrammc" }, { } }; U_BOOT_DRIVER(sdrammc_ast2600) = { .name = "aspeed_ast2600_sdrammc", .id = UCLASS_RAM, .of_match = ast2600_sdrammc_ids, .ops = &ast2600_sdrammc_ops, .ofdata_to_platdata = ast2600_sdrammc_ofdata_to_platdata, .probe = ast2600_sdrammc_probe, .priv_auto_alloc_size = sizeof(struct dram_info), };