# -*- Mode: Python -*- # vim: filetype=python # ## # = Net devices ## { 'include': 'sockets.json' } ## # @set_link: # # Sets the link status of a virtual network adapter. # # @name: the device name of the virtual network adapter # # @up: true to set the link status to be up # # Errors: # - If @name is not a valid network device, DeviceNotFound # # Since: 0.14 # # .. note:: Not all network adapters support setting link status. This # command will succeed even if the network adapter does not support # link status notification. # # .. qmp-example:: # # -> { "execute": "set_link", # "arguments": { "name": "e1000.0", "up": false } } # <- { "return": {} } ## { 'command': 'set_link', 'data': {'name': 'str', 'up': 'bool'} } ## # @netdev_add: # # Add a network backend. # # Additional arguments depend on the type. # # Since: 0.14 # # Errors: # - If @type is not a valid network backend, DeviceNotFound # # .. qmp-example:: # # -> { "execute": "netdev_add", # "arguments": { "type": "user", "id": "netdev1", # "dnssearch": [ { "str": "example.org" } ] } } # <- { "return": {} } ## { 'command': 'netdev_add', 'data': 'Netdev', 'boxed': true, 'allow-preconfig': true } ## # @netdev_del: # # Remove a network backend. # # @id: the name of the network backend to remove # # Errors: # - If @id is not a valid network backend, DeviceNotFound # # Since: 0.14 # # .. qmp-example:: # # -> { "execute": "netdev_del", "arguments": { "id": "netdev1" } } # <- { "return": {} } ## { 'command': 'netdev_del', 'data': {'id': 'str'}, 'allow-preconfig': true } ## # @NetLegacyNicOptions: # # Create a new Network Interface Card. # # @netdev: id of -netdev to connect to # # @macaddr: MAC address # # @model: device model (e1000, rtl8139, virtio etc.) # # @addr: PCI device address # # @vectors: number of MSI-x vectors, 0 to disable MSI-X # # Since: 1.2 ## { 'struct': 'NetLegacyNicOptions', 'data': { '*netdev': 'str', '*macaddr': 'str', '*model': 'str', '*addr': 'str', '*vectors': 'uint32' } } ## # @String: # # A fat type wrapping 'str', to be embedded in lists. # # Since: 1.2 ## { 'struct': 'String', 'data': { 'str': 'str' } } ## # @NetdevUserOptions: # # Use the user mode network stack which requires no administrator # privilege to run. # # @hostname: client hostname reported by the builtin DHCP server # # @restrict: isolate the guest from the host # # @ipv4: whether to support IPv4, default true for enabled (since 2.6) # # @ipv6: whether to support IPv6, default true for enabled (since 2.6) # # @ip: legacy parameter, use net= instead # # @net: IP network address that the guest will see, in the form # addr[/netmask] The netmask is optional, and can be either in the # form a.b.c.d or as a number of valid top-most bits. Default is # 10.0.2.0/24. # # @host: guest-visible address of the host # # @tftp: root directory of the built-in TFTP server # # @bootfile: BOOTP filename, for use with tftp= # # @dhcpstart: the first of the 16 IPs the built-in DHCP server can # assign # # @dns: guest-visible address of the virtual nameserver # # @dnssearch: list of DNS suffixes to search, passed as DHCP option to # the guest # # @domainname: guest-visible domain name of the virtual nameserver # (since 3.0) # # @ipv6-prefix: IPv6 network prefix (default is fec0::) (since 2.6). # The network prefix is given in the usual hexadecimal IPv6 # address notation. # # @ipv6-prefixlen: IPv6 network prefix length (default is 64) (since # 2.6) # # @ipv6-host: guest-visible IPv6 address of the host (since 2.6) # # @ipv6-dns: guest-visible IPv6 address of the virtual nameserver # (since 2.6) # # @smb: root directory of the built-in SMB server # # @smbserver: IP address of the built-in SMB server # # @hostfwd: redirect incoming TCP or UDP host connections to guest # endpoints # # @guestfwd: forward guest TCP connections # # @tftp-server-name: RFC2132 "TFTP server name" string (Since 3.1) # # Since: 1.2 ## { 'struct': 'NetdevUserOptions', 'data': { '*hostname': 'str', '*restrict': 'bool', '*ipv4': 'bool', '*ipv6': 'bool', '*ip': 'str', '*net': 'str', '*host': 'str', '*tftp': 'str', '*bootfile': 'str', '*dhcpstart': 'str', '*dns': 'str', '*dnssearch': ['String'], '*domainname': 'str', '*ipv6-prefix': 'str', '*ipv6-prefixlen': 'int', '*ipv6-host': 'str', '*ipv6-dns': 'str', '*smb': 'str', '*smbserver': 'str', '*hostfwd': ['String'], '*guestfwd': ['String'], '*tftp-server-name': 'str' } } ## # @NetdevTapOptions: # # Used to configure a host TAP network interface backend. # # @ifname: interface name # # @fd: file descriptor of an already opened tap # # @fds: multiple file descriptors of already opened multiqueue capable # tap # # @script: script to initialize the interface # # @downscript: script to shut down the interface # # @br: bridge name (since 2.8) # # @helper: command to execute to configure bridge # # @sndbuf: send buffer limit. Understands [TGMKkb] suffixes. # # @vnet_hdr: enable the IFF_VNET_HDR flag on the tap interface # # @vhost: enable vhost-net network accelerator # # @vhostfd: file descriptor of an already opened vhost net device # # @vhostfds: file descriptors of multiple already opened vhost net # devices # # @vhostforce: vhost on for non-MSIX virtio guests # # @queues: number of queues to be created for multiqueue capable tap # # @poll-us: maximum number of microseconds that could be spent on busy # polling for tap (since 2.7) # # Since: 1.2 ## { 'struct': 'NetdevTapOptions', 'data': { '*ifname': 'str', '*fd': 'str', '*fds': 'str', '*script': 'str', '*downscript': 'str', '*br': 'str', '*helper': 'str', '*sndbuf': 'size', '*vnet_hdr': 'bool', '*vhost': 'bool', '*vhostfd': 'str', '*vhostfds': 'str', '*vhostforce': 'bool', '*queues': 'uint32', '*poll-us': 'uint32'} } ## # @NetdevSocketOptions: # # Socket netdevs are used to establish a network connection to another # QEMU virtual machine via a TCP socket. # # @fd: file descriptor of an already opened socket # # @listen: port number, and optional hostname, to listen on # # @connect: port number, and optional hostname, to connect to # # @mcast: UDP multicast address and port number # # @localaddr: source address and port for multicast and udp packets # # @udp: UDP unicast address and port number # # Since: 1.2 ## { 'struct': 'NetdevSocketOptions', 'data': { '*fd': 'str', '*listen': 'str', '*connect': 'str', '*mcast': 'str', '*localaddr': 'str', '*udp': 'str' } } ## # @NetdevL2TPv3Options: # # Configure an Ethernet over L2TPv3 tunnel. # # @src: source address # # @dst: destination address # # @srcport: source port - mandatory for udp, optional for ip # # @dstport: destination port - mandatory for udp, optional for ip # # @ipv6: force the use of ipv6 # # @udp: use the udp version of l2tpv3 encapsulation # # @cookie64: use 64 bit cookies # # @counter: have sequence counter # # @pincounter: pin sequence counter to zero - workaround for buggy # implementations or networks with packet reorder # # @txcookie: 32 or 64 bit transmit cookie # # @rxcookie: 32 or 64 bit receive cookie # # @txsession: 32 bit transmit session # # @rxsession: 32 bit receive session - if not specified set to the # same value as transmit # # @offset: additional offset - allows the insertion of additional # application-specific data before the packet payload # # Since: 2.1 ## { 'struct': 'NetdevL2TPv3Options', 'data': { 'src': 'str', 'dst': 'str', '*srcport': 'str', '*dstport': 'str', '*ipv6': 'bool', '*udp': 'bool', '*cookie64': 'bool', '*counter': 'bool', '*pincounter': 'bool', '*txcookie': 'uint64', '*rxcookie': 'uint64', 'txsession': 'uint32', '*rxsession': 'uint32', '*offset': 'uint32' } } ## # @NetdevVdeOptions: # # Connect to a vde switch running on the host. # # @sock: socket path # # @port: port number # # @group: group owner of socket # # @mode: permissions for socket # # Since: 1.2 ## { 'struct': 'NetdevVdeOptions', 'data': { '*sock': 'str', '*port': 'uint16', '*group': 'str', '*mode': 'uint16' } } ## # @NetdevBridgeOptions: # # Connect a host TAP network interface to a host bridge device. # # @br: bridge name # # @helper: command to execute to configure bridge # # Since: 1.2 ## { 'struct': 'NetdevBridgeOptions', 'data': { '*br': 'str', '*helper': 'str' } } ## # @NetdevHubPortOptions: # # Connect two or more net clients through a software hub. # # @hubid: hub identifier number # # @netdev: used to connect hub to a netdev instead of a device (since # 2.12) # # Since: 1.2 ## { 'struct': 'NetdevHubPortOptions', 'data': { 'hubid': 'int32', '*netdev': 'str' } } ## # @NetdevNetmapOptions: # # Connect a client to a netmap-enabled NIC or to a VALE switch port # # @ifname: Either the name of an existing network interface supported # by netmap, or the name of a VALE port (created on the fly). A # VALE port name is in the form 'valeXXX:YYY', where XXX and YYY # are non-negative integers. XXX identifies a switch and YYY # identifies a port of the switch. VALE ports having the same XXX # are therefore connected to the same switch. # # @devname: path of the netmap device (default: '/dev/netmap'). # # Since: 2.0 ## { 'struct': 'NetdevNetmapOptions', 'data': { 'ifname': 'str', '*devname': 'str' } } ## # @AFXDPMode: # # Attach mode for a default XDP program # # @skb: generic mode, no driver support necessary # # @native: DRV mode, program is attached to a driver, packets are # passed to the socket without allocation of skb. # # Since: 8.2 ## { 'enum': 'AFXDPMode', 'data': [ 'native', 'skb' ], 'if': 'CONFIG_AF_XDP' } ## # @NetdevAFXDPOptions: # # AF_XDP network backend # # @ifname: The name of an existing network interface. # # @mode: Attach mode for a default XDP program. If not specified, # then 'native' will be tried first, then 'skb'. # # @force-copy: Force XDP copy mode even if device supports zero-copy. # (default: false) # # @queues: number of queues to be used for multiqueue interfaces # (default: 1). # # @start-queue: Use @queues starting from this queue number # (default: 0). # # @inhibit: Don't load a default XDP program, use one already loaded # to the interface (default: false). Requires @sock-fds. # # @sock-fds: A colon (:) separated list of file descriptors for # already open but not bound AF_XDP sockets in the queue order. # One fd per queue. These descriptors should already be added # into XDP socket map for corresponding queues. Requires # @inhibit. # # Since: 8.2 ## { 'struct': 'NetdevAFXDPOptions', 'data': { 'ifname': 'str', '*mode': 'AFXDPMode', '*force-copy': 'bool', '*queues': 'int', '*start-queue': 'int', '*inhibit': 'bool', '*sock-fds': 'str' }, 'if': 'CONFIG_AF_XDP' } ## # @NetdevVhostUserOptions: # # Vhost-user network backend # # @chardev: name of a unix socket chardev # # @vhostforce: vhost on for non-MSIX virtio guests (default: false). # # @queues: number of queues to be created for multiqueue vhost-user # (default: 1) (Since 2.5) # # Since: 2.1 ## { 'struct': 'NetdevVhostUserOptions', 'data': { 'chardev': 'str', '*vhostforce': 'bool', '*queues': 'int' } } ## # @NetdevVhostVDPAOptions: # # Vhost-vdpa network backend # # vDPA device is a device that uses a datapath which complies with the # virtio specifications with a vendor specific control path. # # @vhostdev: path of vhost-vdpa device (default:'/dev/vhost-vdpa-0') # # @vhostfd: file descriptor of an already opened vhost vdpa device # # @queues: number of queues to be created for multiqueue vhost-vdpa # (default: 1) # # @x-svq: Start device with (experimental) shadow virtqueue. (Since # 7.1) (default: false) # # Features: # # @unstable: Member @x-svq is experimental. # # Since: 5.1 ## { 'struct': 'NetdevVhostVDPAOptions', 'data': { '*vhostdev': 'str', '*vhostfd': 'str', '*queues': 'int', '*x-svq': {'type': 'bool', 'features' : [ 'unstable'] } } } ## # @NetdevVmnetHostOptions: # # vmnet (host mode) network backend. # # Allows the vmnet interface to communicate with other vmnet # interfaces that are in host mode and also with the host. # # @start-address: The starting IPv4 address to use for the interface. # Must be in the private IP range (RFC 1918). Must be specified # along with @end-address and @subnet-mask. This address is used # as the gateway address. The subsequent address up to and # including end-address are placed in the DHCP pool. # # @end-address: The DHCP IPv4 range end address to use for the # interface. Must be in the private IP range (RFC 1918). Must be # specified along with @start-address and @subnet-mask. # # @subnet-mask: The IPv4 subnet mask to use on the interface. Must be # specified along with @start-address and @subnet-mask. # # @isolated: Enable isolation for this interface. Interface isolation # ensures that vmnet interface is not able to communicate with any # other vmnet interfaces. Only communication with host is # allowed. Requires at least macOS Big Sur 11.0. # # @net-uuid: The identifier (UUID) to uniquely identify the isolated # network vmnet interface should be added to. If set, no DHCP # service is provided for this interface and network communication # is allowed only with other interfaces added to this network # identified by the UUID. Requires at least macOS Big Sur 11.0. # # Since: 7.1 ## { 'struct': 'NetdevVmnetHostOptions', 'data': { '*start-address': 'str', '*end-address': 'str', '*subnet-mask': 'str', '*isolated': 'bool', '*net-uuid': 'str' }, 'if': 'CONFIG_VMNET' } ## # @NetdevVmnetSharedOptions: # # vmnet (shared mode) network backend. # # Allows traffic originating from the vmnet interface to reach the # Internet through a network address translator (NAT). The vmnet # interface can communicate with the host and with other shared mode # interfaces on the same subnet. If no DHCP settings, subnet mask and # IPv6 prefix specified, the interface can communicate with any of # other interfaces in shared mode. # # @start-address: The starting IPv4 address to use for the interface. # Must be in the private IP range (RFC 1918). Must be specified # along with @end-address and @subnet-mask. This address is used # as the gateway address. The subsequent address up to and # including end-address are placed in the DHCP pool. # # @end-address: The DHCP IPv4 range end address to use for the # interface. Must be in the private IP range (RFC 1918). Must be # specified along with @start-address and @subnet-mask. # # @subnet-mask: The IPv4 subnet mask to use on the interface. Must be # specified along with @start-address and @subnet-mask. # # @isolated: Enable isolation for this interface. Interface isolation # ensures that vmnet interface is not able to communicate with any # other vmnet interfaces. Only communication with host is # allowed. Requires at least macOS Big Sur 11.0. # # @nat66-prefix: The IPv6 prefix to use into guest network. Must be a # unique local address i.e. start with fd00::/8 and have length of # 64. # # Since: 7.1 ## { 'struct': 'NetdevVmnetSharedOptions', 'data': { '*start-address': 'str', '*end-address': 'str', '*subnet-mask': 'str', '*isolated': 'bool', '*nat66-prefix': 'str' }, 'if': 'CONFIG_VMNET' } ## # @NetdevVmnetBridgedOptions: # # vmnet (bridged mode) network backend. # # Bridges the vmnet interface with a physical network interface. # # @ifname: The name of the physical interface to be bridged. # # @isolated: Enable isolation for this interface. Interface isolation # ensures that vmnet interface is not able to communicate with any # other vmnet interfaces. Only communication with host is # allowed. Requires at least macOS Big Sur 11.0. # # Since: 7.1 ## { 'struct': 'NetdevVmnetBridgedOptions', 'data': { 'ifname': 'str', '*isolated': 'bool' }, 'if': 'CONFIG_VMNET' } ## # @NetdevStreamOptions: # # Configuration info for stream socket netdev # # @addr: socket address to listen on (server=true) or connect to # (server=false) # # @server: create server socket (default: false) # # @reconnect: For a client socket, if a socket is disconnected, then # attempt a reconnect after the given number of seconds. Setting # this to zero disables this function. (default: 0) (since 8.0) # # Only SocketAddress types 'unix', 'inet' and 'fd' are supported. # # Since: 7.2 ## { 'struct': 'NetdevStreamOptions', 'data': { 'addr': 'SocketAddress', '*server': 'bool', '*reconnect': 'uint32' } } ## # @NetdevDgramOptions: # # Configuration info for datagram socket netdev. # # @remote: remote address # # @local: local address # # Only SocketAddress types 'unix', 'inet' and 'fd' are supported. # # If remote address is present and it's a multicast address, local # address is optional. Otherwise local address is required and remote # address is optional. # # .. table:: Valid parameters combination table # :widths: auto # # ============= ======== ===== # remote local okay? # ============= ======== ===== # absent absent no # absent not fd no # absent fd yes # multicast absent yes # multicast present yes # not multicast absent no # not multicast present yes # ============= ======== ===== # # Since: 7.2 ## { 'struct': 'NetdevDgramOptions', 'data': { '*local': 'SocketAddress', '*remote': 'SocketAddress' } } ## # @NetClientDriver: # # Available netdev drivers. # # @l2tpv3: since 2.1 # @vhost-vdpa: since 5.1 # @vmnet-host: since 7.1 # @vmnet-shared: since 7.1 # @vmnet-bridged: since 7.1 # @stream: since 7.2 # @dgram: since 7.2 # @af-xdp: since 8.2 # # Since: 2.7 ## { 'enum': 'NetClientDriver', 'data': [ 'none', 'nic', 'user', 'tap', 'l2tpv3', 'socket', 'stream', 'dgram', 'vde', 'bridge', 'hubport', 'netmap', 'vhost-user', 'vhost-vdpa', { 'name': 'af-xdp', 'if': 'CONFIG_AF_XDP' }, { 'name': 'vmnet-host', 'if': 'CONFIG_VMNET' }, { 'name': 'vmnet-shared', 'if': 'CONFIG_VMNET' }, { 'name': 'vmnet-bridged', 'if': 'CONFIG_VMNET' }] } ## # @Netdev: # # Captures the configuration of a network device. # # @id: identifier for monitor commands. # # @type: Specify the driver used for interpreting remaining arguments. # # Since: 1.2 ## { 'union': 'Netdev', 'base': { 'id': 'str', 'type': 'NetClientDriver' }, 'discriminator': 'type', 'data': { 'nic': 'NetLegacyNicOptions', 'user': 'NetdevUserOptions', 'tap': 'NetdevTapOptions', 'l2tpv3': 'NetdevL2TPv3Options', 'socket': 'NetdevSocketOptions', 'stream': 'NetdevStreamOptions', 'dgram': 'NetdevDgramOptions', 'vde': 'NetdevVdeOptions', 'bridge': 'NetdevBridgeOptions', 'hubport': 'NetdevHubPortOptions', 'netmap': 'NetdevNetmapOptions', 'af-xdp': { 'type': 'NetdevAFXDPOptions', 'if': 'CONFIG_AF_XDP' }, 'vhost-user': 'NetdevVhostUserOptions', 'vhost-vdpa': 'NetdevVhostVDPAOptions', 'vmnet-host': { 'type': 'NetdevVmnetHostOptions', 'if': 'CONFIG_VMNET' }, 'vmnet-shared': { 'type': 'NetdevVmnetSharedOptions', 'if': 'CONFIG_VMNET' }, 'vmnet-bridged': { 'type': 'NetdevVmnetBridgedOptions', 'if': 'CONFIG_VMNET' } } } ## # @RxState: # # Packets receiving state # # @normal: filter assigned packets according to the mac-table # # @none: don't receive any assigned packet # # @all: receive all assigned packets # # Since: 1.6 ## { 'enum': 'RxState', 'data': [ 'normal', 'none', 'all' ] } ## # @RxFilterInfo: # # Rx-filter information for a NIC. # # @name: net client name # # @promiscuous: whether promiscuous mode is enabled # # @multicast: multicast receive state # # @unicast: unicast receive state # # @vlan: vlan receive state (Since 2.0) # # @broadcast-allowed: whether to receive broadcast # # @multicast-overflow: multicast table is overflowed or not # # @unicast-overflow: unicast table is overflowed or not # # @main-mac: the main macaddr string # # @vlan-table: a list of active vlan id # # @unicast-table: a list of unicast macaddr string # # @multicast-table: a list of multicast macaddr string # # Since: 1.6 ## { 'struct': 'RxFilterInfo', 'data': { 'name': 'str', 'promiscuous': 'bool', 'multicast': 'RxState', 'unicast': 'RxState', 'vlan': 'RxState', 'broadcast-allowed': 'bool', 'multicast-overflow': 'bool', 'unicast-overflow': 'bool', 'main-mac': 'str', 'vlan-table': ['int'], 'unicast-table': ['str'], 'multicast-table': ['str'] }} ## # @query-rx-filter: # # Return rx-filter information for all NICs (or for the given NIC). # # @name: net client name # # Returns: list of @RxFilterInfo for all NICs (or for the given NIC). # # Errors: # - if the given @name doesn't exist # - if the given NIC doesn't support rx-filter querying # - if the given net client isn't a NIC # # Since: 1.6 # # .. qmp-example:: # # -> { "execute": "query-rx-filter", "arguments": { "name": "vnet0" } } # <- { "return": [ # { # "promiscuous": true, # "name": "vnet0", # "main-mac": "52:54:00:12:34:56", # "unicast": "normal", # "vlan": "normal", # "vlan-table": [ # 4, # 0 # ], # "unicast-table": [ # ], # "multicast": "normal", # "multicast-overflow": false, # "unicast-overflow": false, # "multicast-table": [ # "01:00:5e:00:00:01", # "33:33:00:00:00:01", # "33:33:ff:12:34:56" # ], # "broadcast-allowed": false # } # ] # } ## { 'command': 'query-rx-filter', 'data': { '*name': 'str' }, 'returns': ['RxFilterInfo'] } ## # @NIC_RX_FILTER_CHANGED: # # Emitted once until the 'query-rx-filter' command is executed, the # first event will always be emitted # # @name: net client name # # @path: device path # # Since: 1.6 # # .. qmp-example:: # # <- { "event": "NIC_RX_FILTER_CHANGED", # "data": { "name": "vnet0", # "path": "/machine/peripheral/vnet0/virtio-backend" }, # "timestamp": { "seconds": 1368697518, "microseconds": 326866 } } ## { 'event': 'NIC_RX_FILTER_CHANGED', 'data': { '*name': 'str', 'path': 'str' } } ## # @AnnounceParameters: # # Parameters for self-announce timers # # @initial: Initial delay (in ms) before sending the first GARP/RARP # announcement # # @max: Maximum delay (in ms) between GARP/RARP announcement packets # # @rounds: Number of self-announcement attempts # # @step: Delay increase (in ms) after each self-announcement attempt # # @interfaces: An optional list of interface names, which restricts # the announcement to the listed interfaces. (Since 4.1) # # @id: A name to be used to identify an instance of announce-timers # and to allow it to modified later. Not for use as part of the # migration parameters. (Since 4.1) # # Since: 4.0 ## { 'struct': 'AnnounceParameters', 'data': { 'initial': 'int', 'max': 'int', 'rounds': 'int', 'step': 'int', '*interfaces': ['str'], '*id' : 'str' } } ## # @announce-self: # # Trigger generation of broadcast RARP frames to update network # switches. This can be useful when network bonds fail-over the # active slave. # # TODO: This line is a hack to separate the example from the body # # .. qmp-example:: # # -> { "execute": "announce-self", # "arguments": { # "initial": 50, "max": 550, "rounds": 10, "step": 50, # "interfaces": ["vn2", "vn3"], "id": "bob" } } # <- { "return": {} } # # Since: 4.0 ## { 'command': 'announce-self', 'boxed': true, 'data' : 'AnnounceParameters'} ## # @FAILOVER_NEGOTIATED: # # Emitted when VIRTIO_NET_F_STANDBY was enabled during feature # negotiation. Failover primary devices which were hidden (not # hotplugged when requested) before will now be hotplugged by the # virtio-net standby device. # # @device-id: QEMU device id of the unplugged device # # Since: 4.2 # # .. qmp-example:: # # <- { "event": "FAILOVER_NEGOTIATED", # "data": { "device-id": "net1" }, # "timestamp": { "seconds": 1368697518, "microseconds": 326866 } } ## { 'event': 'FAILOVER_NEGOTIATED', 'data': {'device-id': 'str'} } ## # @NETDEV_STREAM_CONNECTED: # # Emitted when the netdev stream backend is connected # # @netdev-id: QEMU netdev id that is connected # # @addr: The destination address # # Since: 7.2 # # .. qmp-example:: # # <- { "event": "NETDEV_STREAM_CONNECTED", # "data": { "netdev-id": "netdev0", # "addr": { "port": "47666", "ipv6": true, # "host": "::1", "type": "inet" } }, # "timestamp": { "seconds": 1666269863, "microseconds": 311222 } } # # .. qmp-example:: # # <- { "event": "NETDEV_STREAM_CONNECTED", # "data": { "netdev-id": "netdev0", # "addr": { "path": "/tmp/qemu0", "type": "unix" } }, # "timestamp": { "seconds": 1666269706, "microseconds": 413651 } } ## { 'event': 'NETDEV_STREAM_CONNECTED', 'data': { 'netdev-id': 'str', 'addr': 'SocketAddress' } } ## # @NETDEV_STREAM_DISCONNECTED: # # Emitted when the netdev stream backend is disconnected # # @netdev-id: QEMU netdev id that is disconnected # # Since: 7.2 # # .. qmp-example:: # # <- { "event": "NETDEV_STREAM_DISCONNECTED", # "data": {"netdev-id": "netdev0"}, # "timestamp": {"seconds": 1663330937, "microseconds": 526695} } ## { 'event': 'NETDEV_STREAM_DISCONNECTED', 'data': { 'netdev-id': 'str' } }