/* * CFI parallel flash with Intel command set emulation * * Copyright (c) 2006 Thorsten Zitterell * Copyright (c) 2005 Jocelyn Mayer * * This library is free software; you can redistribute it and/or * modify it under the terms of the GNU Lesser General Public * License as published by the Free Software Foundation; either * version 2.1 of the License, or (at your option) any later version. * * This library is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * Lesser General Public License for more details. * * You should have received a copy of the GNU Lesser General Public * License along with this library; if not, see . */ /* * For now, this code can emulate flashes of 1, 2 or 4 bytes width. * Supported commands/modes are: * - flash read * - flash write * - flash ID read * - sector erase * - CFI queries * * It does not support timings * It does not support flash interleaving * It does not implement software data protection as found in many real chips * It does not implement erase suspend/resume commands * It does not implement multiple sectors erase * * It does not implement much more ... */ #include "qemu/osdep.h" #include "hw/block/block.h" #include "hw/block/flash.h" #include "hw/qdev-properties.h" #include "hw/qdev-properties-system.h" #include "sysemu/block-backend.h" #include "qapi/error.h" #include "qemu/error-report.h" #include "qemu/bitops.h" #include "qemu/host-utils.h" #include "qemu/log.h" #include "qemu/module.h" #include "qemu/option.h" #include "hw/sysbus.h" #include "migration/vmstate.h" #include "sysemu/blockdev.h" #include "sysemu/runstate.h" #include "trace.h" #define PFLASH_BE 0 #define PFLASH_SECURE 1 struct PFlashCFI01 { /*< private >*/ SysBusDevice parent_obj; /*< public >*/ BlockBackend *blk; uint32_t nb_blocs; uint64_t sector_len; uint8_t bank_width; uint8_t device_width; /* If 0, device width not specified. */ uint8_t max_device_width; /* max device width in bytes */ uint32_t features; uint8_t wcycle; /* if 0, the flash is read normally */ bool ro; uint8_t cmd; uint8_t status; uint16_t ident0; uint16_t ident1; uint16_t ident2; uint16_t ident3; uint8_t cfi_table[0x52]; uint64_t counter; uint32_t writeblock_size; MemoryRegion mem; char *name; void *storage; VMChangeStateEntry *vmstate; bool old_multiple_chip_handling; /* block update buffer */ unsigned char *blk_bytes; uint32_t blk_offset; }; static int pflash_post_load(void *opaque, int version_id); static bool pflash_blk_write_state_needed(void *opaque) { PFlashCFI01 *pfl = opaque; return (pfl->blk_offset != -1); } static const VMStateDescription vmstate_pflash_blk_write = { .name = "pflash_cfi01_blk_write", .version_id = 1, .minimum_version_id = 1, .needed = pflash_blk_write_state_needed, .fields = (const VMStateField[]) { VMSTATE_VBUFFER_UINT32(blk_bytes, PFlashCFI01, 0, NULL, writeblock_size), VMSTATE_UINT32(blk_offset, PFlashCFI01), VMSTATE_END_OF_LIST() } }; static const VMStateDescription vmstate_pflash = { .name = "pflash_cfi01", .version_id = 1, .minimum_version_id = 1, .post_load = pflash_post_load, .fields = (const VMStateField[]) { VMSTATE_UINT8(wcycle, PFlashCFI01), VMSTATE_UINT8(cmd, PFlashCFI01), VMSTATE_UINT8(status, PFlashCFI01), VMSTATE_UINT64(counter, PFlashCFI01), VMSTATE_END_OF_LIST() }, .subsections = (const VMStateDescription * const []) { &vmstate_pflash_blk_write, NULL } }; /* * Perform a CFI query based on the bank width of the flash. * If this code is called we know we have a device_width set for * this flash. */ static uint32_t pflash_cfi_query(PFlashCFI01 *pfl, hwaddr offset) { int i; uint32_t resp = 0; hwaddr boff; /* * Adjust incoming offset to match expected device-width * addressing. CFI query addresses are always specified in terms of * the maximum supported width of the device. This means that x8 * devices and x8/x16 devices in x8 mode behave differently. For * devices that are not used at their max width, we will be * provided with addresses that use higher address bits than * expected (based on the max width), so we will shift them lower * so that they will match the addresses used when * device_width==max_device_width. */ boff = offset >> (ctz32(pfl->bank_width) + ctz32(pfl->max_device_width) - ctz32(pfl->device_width)); if (boff >= sizeof(pfl->cfi_table)) { return 0; } /* * Now we will construct the CFI response generated by a single * device, then replicate that for all devices that make up the * bus. For wide parts used in x8 mode, CFI query responses * are different than native byte-wide parts. */ resp = pfl->cfi_table[boff]; if (pfl->device_width != pfl->max_device_width) { /* The only case currently supported is x8 mode for a * wider part. */ if (pfl->device_width != 1 || pfl->bank_width > 4) { trace_pflash_unsupported_device_configuration(pfl->name, pfl->device_width, pfl->max_device_width); return 0; } /* CFI query data is repeated, rather than zero padded for * wide devices used in x8 mode. */ for (i = 1; i < pfl->max_device_width; i++) { resp = deposit32(resp, 8 * i, 8, pfl->cfi_table[boff]); } } /* Replicate responses for each device in bank. */ if (pfl->device_width < pfl->bank_width) { for (i = pfl->device_width; i < pfl->bank_width; i += pfl->device_width) { resp = deposit32(resp, 8 * i, 8 * pfl->device_width, resp); } } return resp; } /* Perform a device id query based on the bank width of the flash. */ static uint32_t pflash_devid_query(PFlashCFI01 *pfl, hwaddr offset) { int i; uint32_t resp; hwaddr boff; /* * Adjust incoming offset to match expected device-width * addressing. Device ID read addresses are always specified in * terms of the maximum supported width of the device. This means * that x8 devices and x8/x16 devices in x8 mode behave * differently. For devices that are not used at their max width, * we will be provided with addresses that use higher address bits * than expected (based on the max width), so we will shift them * lower so that they will match the addresses used when * device_width==max_device_width. */ boff = offset >> (ctz32(pfl->bank_width) + ctz32(pfl->max_device_width) - ctz32(pfl->device_width)); /* * Mask off upper bits which may be used in to query block * or sector lock status at other addresses. * Offsets 2/3 are block lock status, is not emulated. */ switch (boff & 0xFF) { case 0: resp = pfl->ident0; trace_pflash_manufacturer_id(pfl->name, resp); break; case 1: resp = pfl->ident1; trace_pflash_device_id(pfl->name, resp); break; default: trace_pflash_device_info(pfl->name, offset); return 0; } /* Replicate responses for each device in bank. */ if (pfl->device_width < pfl->bank_width) { for (i = pfl->device_width; i < pfl->bank_width; i += pfl->device_width) { resp = deposit32(resp, 8 * i, 8 * pfl->device_width, resp); } } return resp; } static uint32_t pflash_data_read(PFlashCFI01 *pfl, hwaddr offset, int width, int be) { uint8_t *p; uint32_t ret; p = pfl->storage; if (be) { ret = ldn_be_p(p + offset, width); } else { ret = ldn_le_p(p + offset, width); } trace_pflash_data_read(pfl->name, offset, width, ret); return ret; } static uint32_t pflash_read(PFlashCFI01 *pfl, hwaddr offset, int width, int be) { hwaddr boff; uint32_t ret; ret = -1; switch (pfl->cmd) { default: /* This should never happen : reset state & treat it as a read */ trace_pflash_read_unknown_state(pfl->name, pfl->cmd); pfl->wcycle = 0; /* * The command 0x00 is not assigned by the CFI open standard, * but QEMU historically uses it for the READ_ARRAY command (0xff). */ pfl->cmd = 0x00; /* fall through to read code */ case 0x00: /* This model reset value for READ_ARRAY (not CFI compliant) */ /* Flash area read */ ret = pflash_data_read(pfl, offset, width, be); break; case 0x10: /* Single byte program */ case 0x20: /* Block erase */ case 0x28: /* Block erase */ case 0x40: /* single byte program */ case 0x50: /* Clear status register */ case 0x60: /* Block /un)lock */ case 0x70: /* Status Register */ case 0xe8: /* Write block */ /* * Status register read. Return status from each device in * bank. */ ret = pfl->status; if (pfl->device_width && width > pfl->device_width) { int shift = pfl->device_width * 8; while (shift + pfl->device_width * 8 <= width * 8) { ret |= pfl->status << shift; shift += pfl->device_width * 8; } } else if (!pfl->device_width && width > 2) { /* * Handle 32 bit flash cases where device width is not * set. (Existing behavior before device width added.) */ ret |= pfl->status << 16; } trace_pflash_read_status(pfl->name, ret); break; case 0x90: if (!pfl->device_width) { /* Preserve old behavior if device width not specified */ boff = offset & 0xFF; if (pfl->bank_width == 2) { boff = boff >> 1; } else if (pfl->bank_width == 4) { boff = boff >> 2; } switch (boff) { case 0: ret = pfl->ident0 << 8 | pfl->ident1; trace_pflash_manufacturer_id(pfl->name, ret); break; case 1: ret = pfl->ident2 << 8 | pfl->ident3; trace_pflash_device_id(pfl->name, ret); break; default: trace_pflash_device_info(pfl->name, boff); ret = 0; break; } } else { /* * If we have a read larger than the bank_width, combine multiple * manufacturer/device ID queries into a single response. */ int i; for (i = 0; i < width; i += pfl->bank_width) { ret = deposit32(ret, i * 8, pfl->bank_width * 8, pflash_devid_query(pfl, offset + i * pfl->bank_width)); } } break; case 0x98: /* Query mode */ if (!pfl->device_width) { /* Preserve old behavior if device width not specified */ boff = offset & 0xFF; if (pfl->bank_width == 2) { boff = boff >> 1; } else if (pfl->bank_width == 4) { boff = boff >> 2; } if (boff < sizeof(pfl->cfi_table)) { ret = pfl->cfi_table[boff]; } else { ret = 0; } } else { /* * If we have a read larger than the bank_width, combine multiple * CFI queries into a single response. */ int i; for (i = 0; i < width; i += pfl->bank_width) { ret = deposit32(ret, i * 8, pfl->bank_width * 8, pflash_cfi_query(pfl, offset + i * pfl->bank_width)); } } break; } trace_pflash_io_read(pfl->name, offset, width, ret, pfl->cmd, pfl->wcycle); return ret; } /* update flash content on disk */ static void pflash_update(PFlashCFI01 *pfl, int offset, int size) { int offset_end; int ret; if (pfl->blk) { offset_end = offset + size; /* widen to sector boundaries */ offset = QEMU_ALIGN_DOWN(offset, BDRV_SECTOR_SIZE); offset_end = QEMU_ALIGN_UP(offset_end, BDRV_SECTOR_SIZE); ret = blk_pwrite(pfl->blk, offset, offset_end - offset, pfl->storage + offset, 0); if (ret < 0) { /* TODO set error bit in status */ error_report("Could not update PFLASH: %s", strerror(-ret)); } } } /* copy current flash content to block update buffer */ static void pflash_blk_write_start(PFlashCFI01 *pfl, hwaddr offset) { hwaddr mask = ~(pfl->writeblock_size - 1); trace_pflash_write_block_start(pfl->name, pfl->counter); pfl->blk_offset = offset & mask; memcpy(pfl->blk_bytes, pfl->storage + pfl->blk_offset, pfl->writeblock_size); } /* commit block update buffer changes */ static void pflash_blk_write_flush(PFlashCFI01 *pfl) { g_assert(pfl->blk_offset != -1); trace_pflash_write_block_flush(pfl->name); memcpy(pfl->storage + pfl->blk_offset, pfl->blk_bytes, pfl->writeblock_size); pflash_update(pfl, pfl->blk_offset, pfl->writeblock_size); pfl->blk_offset = -1; } /* discard block update buffer changes */ static void pflash_blk_write_abort(PFlashCFI01 *pfl) { trace_pflash_write_block_abort(pfl->name); pfl->blk_offset = -1; } static inline void pflash_data_write(PFlashCFI01 *pfl, hwaddr offset, uint32_t value, int width, int be) { uint8_t *p; if (pfl->blk_offset != -1) { /* block write: redirect writes to block update buffer */ if ((offset < pfl->blk_offset) || (offset + width > pfl->blk_offset + pfl->writeblock_size)) { pfl->status |= 0x10; /* Programming error */ return; } trace_pflash_data_write_block(pfl->name, offset, width, value, pfl->counter); p = pfl->blk_bytes + (offset - pfl->blk_offset); } else { /* write directly to storage */ trace_pflash_data_write(pfl->name, offset, width, value); p = pfl->storage + offset; } if (be) { stn_be_p(p, width, value); } else { stn_le_p(p, width, value); } } static void pflash_write(PFlashCFI01 *pfl, hwaddr offset, uint32_t value, int width, int be) { uint8_t *p; uint8_t cmd; cmd = value; trace_pflash_io_write(pfl->name, offset, width, value, pfl->wcycle); if (!pfl->wcycle) { /* Set the device in I/O access mode */ memory_region_rom_device_set_romd(&pfl->mem, false); } switch (pfl->wcycle) { case 0: /* read mode */ switch (cmd) { case 0x00: /* This model reset value for READ_ARRAY (not CFI) */ goto mode_read_array; case 0x10: /* Single Byte Program */ case 0x40: /* Single Byte Program */ trace_pflash_write(pfl->name, "single byte program (0)"); break; case 0x20: /* Block erase */ p = pfl->storage; offset &= ~(pfl->sector_len - 1); trace_pflash_write_block_erase(pfl->name, offset, pfl->sector_len); if (!pfl->ro) { memset(p + offset, 0xff, pfl->sector_len); pflash_update(pfl, offset, pfl->sector_len); } else { pfl->status |= 0x20; /* Block erase error */ } pfl->status |= 0x80; /* Ready! */ break; case 0x50: /* Clear status bits */ trace_pflash_write(pfl->name, "clear status bits"); pfl->status = 0x0; goto mode_read_array; case 0x60: /* Block (un)lock */ trace_pflash_write(pfl->name, "block unlock"); break; case 0x70: /* Status Register */ trace_pflash_write(pfl->name, "read status register"); pfl->cmd = cmd; return; case 0x90: /* Read Device ID */ trace_pflash_write(pfl->name, "read device information"); pfl->cmd = cmd; return; case 0x98: /* CFI query */ trace_pflash_write(pfl->name, "CFI query"); break; case 0xe8: /* Write to buffer */ trace_pflash_write(pfl->name, "write to buffer"); pfl->status |= 0x80; /* Ready! */ break; case 0xf0: /* Probe for AMD flash */ trace_pflash_write(pfl->name, "probe for AMD flash"); goto mode_read_array; case 0xff: /* Read Array */ trace_pflash_write(pfl->name, "read array mode"); goto mode_read_array; default: goto error_flash; } pfl->wcycle++; pfl->cmd = cmd; break; case 1: switch (pfl->cmd) { case 0x10: /* Single Byte Program */ case 0x40: /* Single Byte Program */ trace_pflash_write(pfl->name, "single byte program (1)"); if (!pfl->ro) { pflash_data_write(pfl, offset, value, width, be); pflash_update(pfl, offset, width); } else { pfl->status |= 0x10; /* Programming error */ } pfl->status |= 0x80; /* Ready! */ pfl->wcycle = 0; break; case 0x20: /* Block erase */ case 0x28: if (cmd == 0xd0) { /* confirm */ pfl->wcycle = 0; pfl->status |= 0x80; } else if (cmd == 0xff) { /* Read Array */ goto mode_read_array; } else goto error_flash; break; case 0xe8: /* * Mask writeblock size based on device width, or bank width if * device width not specified. */ /* FIXME check @offset, @width */ if (pfl->device_width) { value = extract32(value, 0, pfl->device_width * 8); } else { value = extract32(value, 0, pfl->bank_width * 8); } pfl->counter = value; pfl->wcycle++; break; case 0x60: if (cmd == 0xd0) { pfl->wcycle = 0; pfl->status |= 0x80; } else if (cmd == 0x01) { pfl->wcycle = 0; pfl->status |= 0x80; } else if (cmd == 0xff) { /* Read Array */ goto mode_read_array; } else { trace_pflash_write(pfl->name, "unknown (un)locking command"); goto mode_read_array; } break; case 0x98: if (cmd == 0xff) { /* Read Array */ goto mode_read_array; } else { trace_pflash_write(pfl->name, "leaving query mode"); } break; default: goto error_flash; } break; case 2: switch (pfl->cmd) { case 0xe8: /* Block write */ /* FIXME check @offset, @width */ if (pfl->blk_offset == -1 && pfl->counter) { pflash_blk_write_start(pfl, offset); } if (!pfl->ro && (pfl->blk_offset != -1)) { pflash_data_write(pfl, offset, value, width, be); } else { pfl->status |= 0x10; /* Programming error */ } pfl->status |= 0x80; if (!pfl->counter) { trace_pflash_write(pfl->name, "block write finished"); pfl->wcycle++; break; } pfl->counter--; break; default: goto error_flash; } break; case 3: /* Confirm mode */ switch (pfl->cmd) { case 0xe8: /* Block write */ if ((cmd == 0xd0) && !(pfl->status & 0x10)) { pflash_blk_write_flush(pfl); pfl->wcycle = 0; pfl->status |= 0x80; } else { pflash_blk_write_abort(pfl); goto mode_read_array; } break; default: pflash_blk_write_abort(pfl); goto error_flash; } break; default: /* Should never happen */ trace_pflash_write(pfl->name, "invalid write state"); goto mode_read_array; } return; error_flash: qemu_log_mask(LOG_UNIMP, "%s: Unimplemented flash cmd sequence " "(offset " HWADDR_FMT_plx ", wcycle 0x%x cmd 0x%x value 0x%x)" "\n", __func__, offset, pfl->wcycle, pfl->cmd, value); mode_read_array: trace_pflash_mode_read_array(pfl->name); memory_region_rom_device_set_romd(&pfl->mem, true); pfl->wcycle = 0; pfl->cmd = 0x00; /* This model reset value for READ_ARRAY (not CFI) */ } static MemTxResult pflash_mem_read_with_attrs(void *opaque, hwaddr addr, uint64_t *value, unsigned len, MemTxAttrs attrs) { PFlashCFI01 *pfl = opaque; bool be = !!(pfl->features & (1 << PFLASH_BE)); if ((pfl->features & (1 << PFLASH_SECURE)) && !attrs.secure) { *value = pflash_data_read(opaque, addr, len, be); } else { *value = pflash_read(opaque, addr, len, be); } return MEMTX_OK; } static MemTxResult pflash_mem_write_with_attrs(void *opaque, hwaddr addr, uint64_t value, unsigned len, MemTxAttrs attrs) { PFlashCFI01 *pfl = opaque; bool be = !!(pfl->features & (1 << PFLASH_BE)); if ((pfl->features & (1 << PFLASH_SECURE)) && !attrs.secure) { return MEMTX_ERROR; } else { pflash_write(opaque, addr, value, len, be); return MEMTX_OK; } } static const MemoryRegionOps pflash_cfi01_ops = { .read_with_attrs = pflash_mem_read_with_attrs, .write_with_attrs = pflash_mem_write_with_attrs, .endianness = DEVICE_NATIVE_ENDIAN, }; static void pflash_cfi01_fill_cfi_table(PFlashCFI01 *pfl) { uint64_t blocks_per_device, sector_len_per_device, device_len; int num_devices; /* * These are only used to expose the parameters of each device * in the cfi_table[]. */ num_devices = pfl->device_width ? (pfl->bank_width / pfl->device_width) : 1; if (pfl->old_multiple_chip_handling) { blocks_per_device = pfl->nb_blocs / num_devices; sector_len_per_device = pfl->sector_len; } else { blocks_per_device = pfl->nb_blocs; sector_len_per_device = pfl->sector_len / num_devices; } device_len = sector_len_per_device * blocks_per_device; /* Hardcoded CFI table */ /* Standard "QRY" string */ pfl->cfi_table[0x10] = 'Q'; pfl->cfi_table[0x11] = 'R'; pfl->cfi_table[0x12] = 'Y'; /* Command set (Intel) */ pfl->cfi_table[0x13] = 0x01; pfl->cfi_table[0x14] = 0x00; /* Primary extended table address (none) */ pfl->cfi_table[0x15] = 0x31; pfl->cfi_table[0x16] = 0x00; /* Alternate command set (none) */ pfl->cfi_table[0x17] = 0x00; pfl->cfi_table[0x18] = 0x00; /* Alternate extended table (none) */ pfl->cfi_table[0x19] = 0x00; pfl->cfi_table[0x1A] = 0x00; /* Vcc min */ pfl->cfi_table[0x1B] = 0x45; /* Vcc max */ pfl->cfi_table[0x1C] = 0x55; /* Vpp min (no Vpp pin) */ pfl->cfi_table[0x1D] = 0x00; /* Vpp max (no Vpp pin) */ pfl->cfi_table[0x1E] = 0x00; /* Reserved */ pfl->cfi_table[0x1F] = 0x07; /* Timeout for min size buffer write */ pfl->cfi_table[0x20] = 0x07; /* Typical timeout for block erase */ pfl->cfi_table[0x21] = 0x0a; /* Typical timeout for full chip erase (4096 ms) */ pfl->cfi_table[0x22] = 0x00; /* Reserved */ pfl->cfi_table[0x23] = 0x04; /* Max timeout for buffer write */ pfl->cfi_table[0x24] = 0x04; /* Max timeout for block erase */ pfl->cfi_table[0x25] = 0x04; /* Max timeout for chip erase */ pfl->cfi_table[0x26] = 0x00; /* Device size */ pfl->cfi_table[0x27] = ctz32(device_len); /* + 1; */ /* Flash device interface (8 & 16 bits) */ pfl->cfi_table[0x28] = 0x02; pfl->cfi_table[0x29] = 0x00; /* Max number of bytes in multi-bytes write */ if (pfl->bank_width == 1) { pfl->cfi_table[0x2A] = 0x08; } else { pfl->cfi_table[0x2A] = 0x0B; } pfl->writeblock_size = 1 << pfl->cfi_table[0x2A]; if (!pfl->old_multiple_chip_handling && num_devices > 1) { pfl->writeblock_size *= num_devices; } pfl->cfi_table[0x2B] = 0x00; /* Number of erase block regions (uniform) */ pfl->cfi_table[0x2C] = 0x01; /* Erase block region 1 */ pfl->cfi_table[0x2D] = blocks_per_device - 1; pfl->cfi_table[0x2E] = (blocks_per_device - 1) >> 8; pfl->cfi_table[0x2F] = sector_len_per_device >> 8; pfl->cfi_table[0x30] = sector_len_per_device >> 16; /* Extended */ pfl->cfi_table[0x31] = 'P'; pfl->cfi_table[0x32] = 'R'; pfl->cfi_table[0x33] = 'I'; pfl->cfi_table[0x34] = '1'; pfl->cfi_table[0x35] = '0'; pfl->cfi_table[0x36] = 0x00; pfl->cfi_table[0x37] = 0x00; pfl->cfi_table[0x38] = 0x00; pfl->cfi_table[0x39] = 0x00; pfl->cfi_table[0x3a] = 0x00; pfl->cfi_table[0x3b] = 0x00; pfl->cfi_table[0x3c] = 0x00; pfl->cfi_table[0x3f] = 0x01; /* Number of protection fields */ } static void pflash_cfi01_realize(DeviceState *dev, Error **errp) { ERRP_GUARD(); PFlashCFI01 *pfl = PFLASH_CFI01(dev); uint64_t total_len; int ret; if (pfl->sector_len == 0) { error_setg(errp, "attribute \"sector-length\" not specified or zero."); return; } if (pfl->nb_blocs == 0) { error_setg(errp, "attribute \"num-blocks\" not specified or zero."); return; } if (pfl->name == NULL) { error_setg(errp, "attribute \"name\" not specified."); return; } total_len = pfl->sector_len * pfl->nb_blocs; memory_region_init_rom_device( &pfl->mem, OBJECT(dev), &pflash_cfi01_ops, pfl, pfl->name, total_len, errp); if (*errp) { return; } pfl->storage = memory_region_get_ram_ptr(&pfl->mem); sysbus_init_mmio(SYS_BUS_DEVICE(dev), &pfl->mem); if (pfl->blk) { uint64_t perm; pfl->ro = !blk_supports_write_perm(pfl->blk); perm = BLK_PERM_CONSISTENT_READ | (pfl->ro ? 0 : BLK_PERM_WRITE); ret = blk_set_perm(pfl->blk, perm, BLK_PERM_ALL, errp); if (ret < 0) { return; } } else { pfl->ro = false; } if (pfl->blk) { if (!blk_check_size_and_read_all(pfl->blk, dev, pfl->storage, total_len, errp)) { vmstate_unregister_ram(&pfl->mem, DEVICE(pfl)); return; } } /* * Default to devices being used at their maximum device width. This was * assumed before the device_width support was added. */ if (!pfl->max_device_width) { pfl->max_device_width = pfl->device_width; } pfl->wcycle = 0; /* * The command 0x00 is not assigned by the CFI open standard, * but QEMU historically uses it for the READ_ARRAY command (0xff). */ pfl->cmd = 0x00; pfl->status = 0x80; /* WSM ready */ pflash_cfi01_fill_cfi_table(pfl); pfl->blk_bytes = g_malloc(pfl->writeblock_size); pfl->blk_offset = -1; } static void pflash_cfi01_system_reset(DeviceState *dev) { PFlashCFI01 *pfl = PFLASH_CFI01(dev); trace_pflash_reset(pfl->name); /* * The command 0x00 is not assigned by the CFI open standard, * but QEMU historically uses it for the READ_ARRAY command (0xff). */ pfl->cmd = 0x00; pfl->wcycle = 0; memory_region_rom_device_set_romd(&pfl->mem, true); /* * The WSM ready timer occurs at most 150ns after system reset. * This model deliberately ignores this delay. */ pfl->status = 0x80; pfl->blk_offset = -1; } static Property pflash_cfi01_properties[] = { DEFINE_PROP_DRIVE("drive", PFlashCFI01, blk), /* num-blocks is the number of blocks actually visible to the guest, * ie the total size of the device divided by the sector length. * If we're emulating flash devices wired in parallel the actual * number of blocks per individual device will differ. */ DEFINE_PROP_UINT32("num-blocks", PFlashCFI01, nb_blocs, 0), DEFINE_PROP_UINT64("sector-length", PFlashCFI01, sector_len, 0), /* width here is the overall width of this QEMU device in bytes. * The QEMU device may be emulating a number of flash devices * wired up in parallel; the width of each individual flash * device should be specified via device-width. If the individual * devices have a maximum width which is greater than the width * they are being used for, this maximum width should be set via * max-device-width (which otherwise defaults to device-width). * So for instance a 32-bit wide QEMU flash device made from four * 16-bit flash devices used in 8-bit wide mode would be configured * with width = 4, device-width = 1, max-device-width = 2. * * If device-width is not specified we default to backwards * compatible behaviour which is a bad emulation of two * 16 bit devices making up a 32 bit wide QEMU device. This * is deprecated for new uses of this device. */ DEFINE_PROP_UINT8("width", PFlashCFI01, bank_width, 0), DEFINE_PROP_UINT8("device-width", PFlashCFI01, device_width, 0), DEFINE_PROP_UINT8("max-device-width", PFlashCFI01, max_device_width, 0), DEFINE_PROP_BIT("big-endian", PFlashCFI01, features, PFLASH_BE, 0), DEFINE_PROP_BIT("secure", PFlashCFI01, features, PFLASH_SECURE, 0), DEFINE_PROP_UINT16("id0", PFlashCFI01, ident0, 0), DEFINE_PROP_UINT16("id1", PFlashCFI01, ident1, 0), DEFINE_PROP_UINT16("id2", PFlashCFI01, ident2, 0), DEFINE_PROP_UINT16("id3", PFlashCFI01, ident3, 0), DEFINE_PROP_STRING("name", PFlashCFI01, name), DEFINE_PROP_BOOL("old-multiple-chip-handling", PFlashCFI01, old_multiple_chip_handling, false), DEFINE_PROP_END_OF_LIST(), }; static void pflash_cfi01_class_init(ObjectClass *klass, void *data) { DeviceClass *dc = DEVICE_CLASS(klass); device_class_set_legacy_reset(dc, pflash_cfi01_system_reset); dc->realize = pflash_cfi01_realize; device_class_set_props(dc, pflash_cfi01_properties); dc->vmsd = &vmstate_pflash; set_bit(DEVICE_CATEGORY_STORAGE, dc->categories); } static const TypeInfo pflash_cfi01_info = { .name = TYPE_PFLASH_CFI01, .parent = TYPE_SYS_BUS_DEVICE, .instance_size = sizeof(PFlashCFI01), .class_init = pflash_cfi01_class_init, }; static void pflash_cfi01_register_types(void) { type_register_static(&pflash_cfi01_info); } type_init(pflash_cfi01_register_types) PFlashCFI01 *pflash_cfi01_register(hwaddr base, const char *name, hwaddr size, BlockBackend *blk, uint32_t sector_len, int bank_width, uint16_t id0, uint16_t id1, uint16_t id2, uint16_t id3, int be) { DeviceState *dev = qdev_new(TYPE_PFLASH_CFI01); if (blk) { qdev_prop_set_drive(dev, "drive", blk); } assert(QEMU_IS_ALIGNED(size, sector_len)); qdev_prop_set_uint32(dev, "num-blocks", size / sector_len); qdev_prop_set_uint64(dev, "sector-length", sector_len); qdev_prop_set_uint8(dev, "width", bank_width); qdev_prop_set_bit(dev, "big-endian", !!be); qdev_prop_set_uint16(dev, "id0", id0); qdev_prop_set_uint16(dev, "id1", id1); qdev_prop_set_uint16(dev, "id2", id2); qdev_prop_set_uint16(dev, "id3", id3); qdev_prop_set_string(dev, "name", name); sysbus_realize_and_unref(SYS_BUS_DEVICE(dev), &error_fatal); sysbus_mmio_map(SYS_BUS_DEVICE(dev), 0, base); return PFLASH_CFI01(dev); } BlockBackend *pflash_cfi01_get_blk(PFlashCFI01 *fl) { return fl->blk; } MemoryRegion *pflash_cfi01_get_memory(PFlashCFI01 *fl) { return &fl->mem; } /* * Handle -drive if=pflash for machines that use properties. * If @dinfo is null, do nothing. * Else if @fl's property "drive" is already set, fatal error. * Else set it to the BlockBackend with @dinfo. */ void pflash_cfi01_legacy_drive(PFlashCFI01 *fl, DriveInfo *dinfo) { Location loc; if (!dinfo) { return; } loc_push_none(&loc); qemu_opts_loc_restore(dinfo->opts); if (fl->blk) { error_report("clashes with -machine"); exit(1); } qdev_prop_set_drive_err(DEVICE(fl), "drive", blk_by_legacy_dinfo(dinfo), &error_fatal); loc_pop(&loc); } static void postload_update_cb(void *opaque, bool running, RunState state) { PFlashCFI01 *pfl = opaque; /* This is called after bdrv_activate_all. */ qemu_del_vm_change_state_handler(pfl->vmstate); pfl->vmstate = NULL; trace_pflash_postload_cb(pfl->name); pflash_update(pfl, 0, pfl->sector_len * pfl->nb_blocs); } static int pflash_post_load(void *opaque, int version_id) { PFlashCFI01 *pfl = opaque; if (!pfl->ro) { pfl->vmstate = qemu_add_vm_change_state_handler(postload_update_cb, pfl); } return 0; }