#Example fan monitor definitions for phosphor-fan-monitor

#List the fans that need to be monitored, along with some
#properties that define how much slack is allowed in the actual
#tach value as compared to the target tach value.

#fans:
# - inventory:
#    [The system inventory location for the fan]
#  method: [timebased|count](optional)
#    [Available methods:
#     * timebased - use a percentage based deviation
#     * count - run up/down count fault detection]
#  functional_delay:
#    [Delay (in secs) before a fan is marked functional after returning
#     within the allowed deviation]
#  allowed_out_of_range_time: (required for method timebased)
#    [Time (in secs) actual speed can be outside of deviation of
#     target speed]
#  deviation:
#    [Percentage that actual speed must be within target speed]
#  num_sensors_nonfunc_for_fan_nonfunc:
#    [How many sensors on the fan must be faulted before fan
#     will be considered faulted]
#  sensors: [array of speed sensors for the fan]
#    - name [The name of the fan sensor]
#      has_target [true|false  If this sensor has a Target property for
#                  setting a fan speed (otherwise just for reads)]
#      target_interface [The fan target interface used by the sensor.
#                        Default is "xyz.openbmc_project.Control.FanSpeed"]
#      target_path [The full target path, which implements
#                   xyz.openbmc_project.Control.FanSpeed or
#                   xyz.openbmc_project.Control.FanPwm interface.
#                   Default is /xyz/openbmc_project/sensors/fan_tach/*"]
#      factor [The factor to multiply with target to calculate the expected
#              fan speed. Default is 1 for fan speed target;
#              Customized value for pwm target]
#      offset [The offset to add to calculate the expected fan speed.
#              Default is 0 for fan speed target;
#              Customized value for pwm target]
#  condition: [optional condition function to create fan functional monitoring]
#    name: [The name of an available condition function]
#    properties: [The properties used in the condition function]
#        - object: [Object path of property to use]
#          interface: [Interface of property to use]
#          property:
#              name: [Property name]
#              type: [Property data type]
#              value: [Property value to check condition against]
#
#sensor_trust_groups:
# - class: [Group class name
#           Available classes:
#           * NonzeroSpeed - Only trust if at least one sensor in the group
#                            has a nonzero speed.]
#   group:
#     - name [The name of the fan sensor in this group]
#       in_trust: [true|false] (optional)
#         [Include in trust determination or not. Default = true]

#The code uses these parameters as follows:
#  After a speed reading of a sensor is outside of the allowed deviation of
#  the target speed for the allowed out of range time, if at least
#  num_sensors_nonfunc_for_fan_nonfunc sensors meet this condition,
#  the fan will be set to nonfunctional in the inventory.
#
#  Sensor trust groups are used to specify that the speed values for the
#  sensors in a group cannot be trusted based on some condition, where
#  the condition is based on the class used to implement the group.  All
#  sensors in the group go in and out of trust based on those defined
#  to be part of determining the trust.  This section is optional.

#Example entries for 1 fan system:
#fans:
#  - inventory: /system/chassis/motherboard/fan0
#    functional_delay: 5
#    allowed_out_of_range_time: 15
#    deviation: 15
#    num_sensors_nonfunc_for_fan_nonfunc: 1
#    sensors:
#      - name: fan0
#        has_target: true
#    # Only create fan functional properties and monitor on air cooled
#    condition:
#      name: propertiesMatch
#      properties:
#        - object: /xyz/openbmc_project/inventory/system/chassis
#          interface: xyz.openbmc_project.Inventory.Decorator.CoolingType
#          property:
#            name: WaterCooled
#            type: bool
#            value: false
#sensor_trust_groups:
# - class: NonzeroSpeed
#    group:
#      - name: fan0_0
#        in_trust: false
#      - name: fan0_1

#Example entries for count method fan system:
#fans:
#  - inventory: /system/chassis/motherboard/fan2
#    method: count
#    functional_delay: 5
#    deviation: 15
#    num_sensors_nonfunc_for_fan_nonfunc: 1
#    sensors:
#      - name: fan2
#        has_target: true
#    # Only create fan functional properties and monitor on air cooled
#    condition:
#      name: propertiesMatch
#      properties:
#        - object: /xyz/openbmc_project/inventory/system/chassis
#          interface: xyz.openbmc_project.Inventory.Decorator.CoolingType
#          property:
#            name: WaterCooled
#            type: bool
#            value: false