*** Settings *** Documentation Network interface configuration and verification ... tests. Resource ../../lib/bmc_redfish_resource.robot Resource ../../lib/bmc_network_utils.robot Resource ../../lib/openbmc_ffdc.robot Library ../../lib/bmc_network_utils.py Library Collections Test Setup Test Setup Execution Test Teardown Test Teardown Execution Suite Setup Suite Setup Execution Force Tags Network_Conf_Test *** Variables *** ${test_hostname} openbmc ${test_ipv4_addr} 10.7.7.7 ${test_ipv4_invalid_addr} 0.0.1.a ${test_subnet_mask} 255.255.0.0 ${broadcast_ip} 10.7.7.255 ${loopback_ip} 127.0.0.2 ${multicast_ip} 224.6.6.6 ${out_of_range_ip} 10.7.7.256 ${test_ipv4_addr2} 10.7.7.8 # Valid netmask is 4 bytes long and has continuous block of 1s. # Maximum valid value in each octet is 255 and least value is 0. # 253 is not valid, as binary value is 11111101. ${invalid_netmask} 255.255.253.0 ${alpha_netmask} ff.ff.ff.ff # Maximum value of octet in netmask is 255. ${out_of_range_netmask} 255.256.255.0 ${more_byte_netmask} 255.255.255.0.0 ${less_byte_netmask} 255.255.255 ${threshold_netmask} 255.255.255.255 ${lowest_netmask} 128.0.0.0 # There will be 4 octets in IP address (e.g. xx.xx.xx.xx) # but trying to configure xx.xx.xx ${less_octet_ip} 10.3.36 # For the address 10.6.6.6, the 10.6.6.0 portion describes the # network ID and the 6 describe the host. ${network_id} 10.7.7.0 ${hex_ip} 0xa.0xb.0xc.0xd ${negative_ip} 10.-7.-7.7 @{static_name_servers} 10.5.5.5 @{null_value} null @{empty_dictionary} {} @{string_value} aa.bb.cc.dd *** Test Cases *** Get IP Address And Verify [Documentation] Get IP Address And Verify. [Tags] Get_IP_Address_And_Verify FOR ${network_configuration} IN @{network_configurations} Verify IP On BMC ${network_configuration['Address']} END Get Netmask And Verify [Documentation] Get Netmask And Verify. [Tags] Get_Netmask_And_Verify FOR ${network_configuration} IN @{network_configurations} Verify Netmask On BMC ${network_configuration['SubnetMask']} END Get Gateway And Verify [Documentation] Get gateway and verify it's existence on the BMC. [Tags] Get_Gateway_And_Verify FOR ${network_configuration} IN @{network_configurations} Verify Gateway On BMC ${network_configuration['Gateway']} END Get MAC Address And Verify [Documentation] Get MAC address and verify it's existence on the BMC. [Tags] Get_MAC_Address_And_Verify ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} ${resp}= Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface} ${macaddr}= Get From Dictionary ${resp.dict} MACAddress Validate MAC On BMC ${macaddr} Verify All Configured IP And Netmask [Documentation] Verify all configured IP and netmask on BMC. [Tags] Verify_All_Configured_IP_And_Netmask FOR ${network_configuration} IN @{network_configurations} Verify IP And Netmask On BMC ${network_configuration['Address']} ... ${network_configuration['SubnetMask']} END Get Hostname And Verify [Documentation] Get hostname via Redfish and verify. [Tags] Get_Hostname_And_Verify ${hostname}= Redfish_Utils.Get Attribute ${REDFISH_NW_PROTOCOL_URI} HostName Validate Hostname On BMC ${hostname} Configure Hostname And Verify [Documentation] Configure hostname via Redfish and verify. [Tags] Configure_Hostname_And_Verify [Teardown] Run Keywords ... Configure Hostname ${hostname} AND Validate Hostname On BMC ${hostname} ${hostname}= Redfish_Utils.Get Attribute ${REDFISH_NW_PROTOCOL_URI} HostName Configure Hostname ${test_hostname} Validate Hostname On BMC ${test_hostname} Add Valid IPv4 Address And Verify [Documentation] Add IPv4 Address via Redfish and verify. [Tags] Add_Valid_IPv4_Addres_And_Verify [Teardown] Run Keywords ... Delete IP Address ${test_ipv4_addr} AND Test Teardown Execution Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway} Add Invalid IPv4 Address And Verify [Documentation] Add Invalid IPv4 Address via Redfish and verify. [Tags] Add_Invalid_IPv4_Addres_And_Verify Add IP Address ${test_ipv4_invalid_addr} ${test_subnet_mask} ... ${test_gateway} valid_status_codes=${HTTP_BAD_REQUEST} Configure Out Of Range IP [Documentation] Configure out-of-range IP address. [Tags] Configure_Out_Of_Range_IP [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${out_of_range_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Broadcast IP [Documentation] Configure broadcast IP address. [Tags] Configure_Broadcast_IP [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${broadcast_ip} # ip subnet_mask gateway valid_status_codes ${broadcast_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Multicast IP [Documentation] Configure multicast IP address. [Tags] Configure_Multicast_IP [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${multicast_ip} # ip subnet_mask gateway valid_status_codes ${multicast_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Loopback IP [Documentation] Configure loopback IP address. [Tags] Configure_Loopback_IP [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${loopback_ip} # ip subnet_mask gateway valid_status_codes ${loopback_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Add Valid IPv4 Address And Check Persistency [Documentation] Add IPv4 address and check peristency. [Tags] Add_Valid_IPv4_Addres_And_Check_Persistency Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway} # Reboot BMC and verify persistency. OBMC Reboot (off) Redfish.Login Verify IP On BMC ${test_ipv4_addr} Delete IP Address ${test_ipv4_addr} Add Fourth Octet Threshold IP And Verify [Documentation] Add fourth octet threshold IP and verify. [Tags] Add_Fourth_Octet_Threshold_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 10.7.7.254 AND Test Teardown Execution Add IP Address 10.7.7.254 ${test_subnet_mask} ${test_gateway} Add Fourth Octet Lowest IP And Verify [Documentation] Add fourth octet lowest IP and verify. [Tags] Add_Fourth_Octet_Lowest_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 10.7.7.1 AND Test Teardown Execution Add IP Address 10.7.7.1 ${test_subnet_mask} ${test_gateway} Add Third Octet Threshold IP And Verify [Documentation] Add third octet threshold IP and verify. [Tags] Add_Third_Octet_Threshold_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 10.7.255.7 AND Test Teardown Execution Add IP Address 10.7.255.7 ${test_subnet_mask} ${test_gateway} Add Third Octet Lowest IP And Verify [Documentation] Add third octet lowest IP and verify. [Tags] Add_Third_Octet_Lowest_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 10.7.0.7 AND Test Teardown Execution Add IP Address 10.7.0.7 ${test_subnet_mask} ${test_gateway} Add Second Octet Threshold IP And Verify [Documentation] Add second octet threshold IP and verify. [Tags] Add_Second_Octet_Threshold_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 10.255.7.7 AND Test Teardown Execution Add IP Address 10.255.7.7 ${test_subnet_mask} ${test_gateway} Add Second Octet Lowest IP And Verify [Documentation] Add second octet lowest IP and verify. [Tags] Add_Second_Octet_Lowest_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 10.0.7.7 AND Test Teardown Execution Add IP Address 10.0.7.7 ${test_subnet_mask} ${test_gateway} Add First Octet Threshold IP And Verify [Documentation] Add first octet threshold IP and verify. [Tags] Add_First_Octet_Threshold_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 223.7.7.7 AND Test Teardown Execution Add IP Address 223.7.7.7 ${test_subnet_mask} ${test_gateway} Add First Octet Lowest IP And Verify [Documentation] Add first octet lowest IP and verify. [Tags] Add_First_Octet_Lowest_IP_And_Verify [Teardown] Run Keywords ... Delete IP Address 1.7.7.7 AND Test Teardown Execution Add IP Address 1.7.7.7 ${test_subnet_mask} ${test_gateway} Configure Invalid Netmask [Documentation] Verify error while setting invalid netmask. [Tags] Configure_Invalid_Netmask [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${invalid_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Out Of Range Netmask [Documentation] Verify error while setting out of range netmask. [Tags] Configure_Out_Of_Range_Netmask [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${out_of_range_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Alpha Netmask [Documentation] Verify error while setting alpha netmask. [Tags] Configure_Alpha_Netmask [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${alpha_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure More Byte Netmask [Documentation] Verify error while setting more byte netmask. [Tags] Configure_More_Byte_Netmask [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${more_byte_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Less Byte Netmask [Documentation] Verify error while setting less byte netmask. [Tags] Configure_Less_Byte_Netmask [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${less_byte_netmask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Threshold Netmask And Verify [Documentation] Configure threshold netmask and verify. [Tags] Configure_Threshold_Netmask_And_verify [Teardown] Run Keywords ... Delete IP Address ${test_ipv4_addr} AND Test Teardown Execution Add IP Address ${test_ipv4_addr} ${threshold_netmask} ${test_gateway} Configure Lowest Netmask And Verify [Documentation] Configure lowest netmask and verify. [Tags] Configure_Lowest_Netmask_And_verify [Teardown] Run Keywords ... Delete IP Address ${test_ipv4_addr} AND Test Teardown Execution Add IP Address ${test_ipv4_addr} ${lowest_netmask} ${test_gateway} Configure Network ID [Documentation] Verify error while configuring network ID. [Tags] Configure_Network_ID [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${network_id} # ip subnet_mask gateway valid_status_codes ${network_id} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Less Octet IP [Documentation] Verify error while Configuring less octet IP address. [Tags] Configure_Less_Octet_IP [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${less_octet_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Empty IP [Documentation] Verify error while Configuring empty IP address. [Tags] Configure_Empty_IP [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${EMPTY} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Special Char IP [Documentation] Configure invalid IP address containing special chars. [Tags] Configure_Special_Char_IP [Template] Add IP Address # ip subnet_mask gateway valid_status_codes @@@.%%.44.11 ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Hexadecimal IP [Documentation] Configure invalid IP address containing hex value. [Tags] Configure_Hexadecimal_IP [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${hex_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Negative Octet IP [Documentation] Configure invalid IP address containing negative octet. [Tags] Configure_Negative_Octet_IP [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${negative_ip} ${test_subnet_mask} ${test_gateway} ${HTTP_BAD_REQUEST} Configure Incomplete IP For Gateway [Documentation] Configure incomplete IP for gateway and expect an error. [Tags] Configure_Incomplete_IP_For_Gateway [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} ${less_octet_ip} ${HTTP_BAD_REQUEST} Configure Special Char IP For Gateway [Documentation] Configure special char IP for gateway and expect an error. [Tags] Configure_Special_Char_IP_For_Gateway [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} @@@.%%.44.11 ${HTTP_BAD_REQUEST} Configure Hexadecimal IP For Gateway [Documentation] Configure hexadecimal IP for gateway and expect an error. [Tags] Configure_Hexadecimal_IP_For_Gateway [Template] Add IP Address # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} ${hex_ip} ${HTTP_BAD_REQUEST} Get DNS Server And Verify [Documentation] Get DNS server via Redfish and verify. [Tags] Get_DNS_Server_And_Verify Verify CLI and Redfish Nameservers Configure DNS Server And Verify [Documentation] Configure DNS server and verify. [Tags] Configure_DNS_Server_And_Verify [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution Configure Static Name Servers ${static_name_servers} Verify CLI and Redfish Nameservers Delete DNS Server And Verify [Documentation] Delete DNS server and verify. [Tags] Delete_DNS_Server_And_Verify [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution Delete Static Name Servers Verify CLI and Redfish Nameservers Configure DNS Server And Check Persistency [Documentation] Configure DNS server and check persistency on reboot. [Tags] Configure_DNS_Server_And_Check_Persistency [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution Configure Static Name Servers ${static_name_servers} # Reboot BMC and verify persistency. OBMC Reboot (off) Redfish.Login Verify CLI and Redfish Nameservers Configure Loopback IP For Gateway [Documentation] Configure loopback IP for gateway and expect an error. [Tags] Configure_Loopback_IP_For_Gateway [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${test_ipv4_addr} # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} ${loopback_ip} ${HTTP_BAD_REQUEST} Configure Network ID For Gateway [Documentation] Configure network ID for gateway and expect an error. [Tags] Configure_Network_ID_For_Gateway [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${test_ipv4_addr} # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} ${network_id} ${HTTP_BAD_REQUEST} Configure Multicast IP For Gateway [Documentation] Configure multicast IP for gateway and expect an error. [Tags] Configure_Multicast_IP_For_Gateway [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${test_ipv4_addr} # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} ${multicast_ip} ${HTTP_BAD_REQUEST} Configure Broadcast IP For Gateway [Documentation] Configure broadcast IP for gateway and expect an error. [Tags] Configure_Broadcast_IP_For_Gateway [Template] Add IP Address [Teardown] Clear IP Settings On Fail ${test_ipv4_addr} # ip subnet_mask gateway valid_status_codes ${test_ipv4_addr} ${test_subnet_mask} ${broadcast_ip} ${HTTP_BAD_REQUEST} Configure Null Value For DNS Server [Documentation] Configure null value for DNS server and expect an error. [Tags] Configure_Null_Value_For_DNS_Server [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution Configure Static Name Servers ${null_value} ${HTTP_BAD_REQUEST} Configure Empty Value For DNS Server [Documentation] Configure empty value for DNS server and expect an error. [Tags] Configure_Empty_Value_For_DNS_Server [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution Configure Static Name Servers ${empty_dictionary} ${HTTP_BAD_REQUEST} Configure String Value For DNS Server [Documentation] Configure string value for DNS server and expect an error. [Tags] Configure_String_Value_For_DNS_Server [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution Configure Static Name Servers ${string_value} ${HTTP_BAD_REQUEST} Modify IPv4 Address And Verify [Documentation] Modify IP address via Redfish and verify. [Tags] Modify_IPv4_Addres_And_Verify [Teardown] Run Keywords ... Delete IP Address ${test_ipv4_addr2} AND Test Teardown Execution Add IP Address ${test_ipv4_addr} ${test_subnet_mask} ${test_gateway} Update IP Address ${test_ipv4_addr} ${test_ipv4_addr2} ${test_subnet_mask} ${test_gateway} Configure Invalid Values For DNS Server [Documentation] Configure invalid values for DNS server and expect an error. [Tags] Configure_Invalid_Value_For_DNS_Server [Setup] DNS Test Setup Execution [Template] Configure Static Name Servers [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution # static_name_servers valid_status_codes 0xa.0xb.0xc.0xd ${HTTP_BAD_REQUEST} 10.-7.-7.-7 ${HTTP_BAD_REQUEST} 10.3.36 ${HTTP_BAD_REQUEST} @@@.%%.44.11 ${HTTP_BAD_REQUEST} Config Multiple DNS Servers And Verify [Documentation] Config multiple DNS servers and verify. [Tags] Config_Multiple_DNS_Servers_And_Verify [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution @{list_name_servers}= Create List 10.5.5.10 10.20.5.10 10.5.6.7 Configure Static Name Servers ${list_name_servers} Verify CLI and Redfish Nameservers Configure And Verify Multiple Static IPv4 Addresses [Documentation] Configure multiple static ipv4 address via Redfish and verify. [Tags] Configure_And_Verify_Multiple_Static_IPv4_Addresses [Teardown] Run Keywords Delete Multiple Static IPv4 Addresses ${test_ipv4_addresses} ... AND Test Teardown Execution ${test_ipv4_addresses}= Create List ${test_ipv4_addr} ${test_ipv4_addr2} Configure Multiple Static IPv4 Addresses ${test_ipv4_addresses} ${test_subnet_mask} ${test_gateway} Configure Multiple Static IPv4 Addresses And Check Persistency [Documentation] Configure multiple static ipv4 address via Redfish and check persistency. [Tags] Configure_Multiple_Static_IPv4_Addresses_And_Check_Persistency [Teardown] Run Keywords Delete Multiple Static IPv4 Addresses ${test_ipv4_addresses} ... AND Test Teardown Execution ${test_ipv4_addresses}= Create List ${test_ipv4_addr} ${test_ipv4_addr2} Configure Multiple Static IPv4 Addresses ${test_ipv4_addresses} ${test_subnet_mask} ${test_gateway} # Reboot BMC and verify persistency. OBMC Reboot (off) Redfish.Login FOR ${ip} IN @{test_ipv4_addresses} Verify IP And Netmask On BMC ${ip} ${test_subnet_mask} END Configure And Verify Multiple IPv4 Addresses [Documentation] Configure multiple IPv4 addresses and verify. [Tags] Configure_And_Verify_Multiple_IPv4_Addresse [Teardown] Run Keywords ... Delete IP Address ${test_ipv4_addr} AND Delete IP Address ${test_ipv4_addr2} ... AND Test Teardown Execution ${ip1}= Create dictionary Address=${test_ipv4_addr} ... SubnetMask=255.255.0.0 Gateway=${test_gateway} ${ip2}= Create dictionary Address=${test_ipv4_addr2} ... SubnetMask=255.255.252.0 Gateway=${test_gateway} ${empty_dict}= Create Dictionary ${patch_list}= Create List ${network_configurations}= Get Network Configuration ${num_entries}= Get Length ${network_configurations} FOR ${INDEX} IN RANGE 0 ${num_entries} Append To List ${patch_list} ${empty_dict} END # We need not check for existence of IP on BMC while adding. Append To List ${patch_list} ${ip1} ${ip2} ${payload}= Create Dictionary IPv4StaticAddresses=${patch_list} ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} Redfish.patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface} body=&{payload} ... valid_status_codes=[${HTTP_OK}, ${HTTP_NO_CONTENT}] # Note: Network restart takes around 15-18s after patch request processing. Sleep ${NETWORK_TIMEOUT}s Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT} Verify IP On BMC ${test_ipv4_addr} Verify IP On BMC ${test_ipv4_addr2} Config Multiple DNS Servers And Check Persistency [Documentation] Config multiple DNS and check persistency. [Tags] Config_Multiple_DNS_Servers_And_Check_Persistency [Setup] DNS Test Setup Execution [Teardown] Run Keywords ... Configure Static Name Servers AND Test Teardown Execution @{list_name_servers}= Create List 10.5.5.10 10.20.5.10 10.5.6.7 Configure Static Name Servers ${list_name_servers} # Reboot BMC and verify persistency. OBMC Reboot (off) Redfish.Login Verify CLI and Redfish Nameservers Configure Static IP Without Using Gateway And Verify [Documentation] Configure static IP without using gateway and verify error. [Tags] Configure_Static_IP_Without_Using_Gateway_And_Verify ${ip}= Create dictionary Address=${test_ipv4_addr} ... SubnetMask=${test_subnet_mask} ${empty_dict}= Create Dictionary ${patch_list}= Create List ${network_configurations}= Get Network Configuration ${num_entries}= Get Length ${network_configurations} FOR ${INDEX} IN RANGE 0 ${num_entries} Append To List ${patch_list} ${empty_dict} END # We need not check for existence of IP on BMC while adding. Append To List ${patch_list} ${ip} ${payload}= Create Dictionary IPv4StaticAddresses=${patch_list} ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} Redfish.patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface} ... body=&{payload} valid_status_codes=[${HTTP_BAD_REQUEST}] Test Network Response On Specified Host State [Documentation] Verifying the BMC network response when host is on and off. [Tags] Test_Network_Response_On_Specified_Host_State [Template] Verify Network Response On Specified Host State # host_state on off *** Keywords *** Test Setup Execution [Documentation] Test setup execution. Redfish.Login @{network_configurations}= Get Network Configuration Set Test Variable @{network_configurations} # Get BMC IP address and prefix length. ${ip_data}= Get BMC IP Info Set Test Variable ${ip_data} Verify Netmask On BMC [Documentation] Verify netmask on BMC. [Arguments] ${netmask} # Description of the argument(s): # netmask netmask value to be verified. ${prefix_length}= Netmask Prefix Length ${netmask} Should Contain Match ${ip_data} */${prefix_length} ... msg=Prefix length does not exist. Verify IP And Netmask On BMC [Documentation] Verify IP and netmask on BMC. [Arguments] ${ip} ${netmask} # Description of the argument(s): # ip IP address to be verified. # netmask netmask value to be verified. ${prefix_length}= Netmask Prefix Length ${netmask} @{ip_data}= Get BMC IP Info ${ip_with_netmask}= Catenate ${ip}/${prefix_length} Should Contain ${ip_data} ${ip_with_netmask} ... msg=IP and netmask pair does not exist. Test Teardown Execution [Documentation] Test teardown execution. FFDC On Test Case Fail Redfish.Logout Clear IP Settings On Fail [Documentation] Clear IP settings on fail. [Arguments] ${ip} # Description of argument(s): # ip IP address to be deleted. Run Keyword If '${TEST STATUS}' == 'FAIL' ... Delete IP Address ${ip} Test Teardown Execution Verify CLI and Redfish Nameservers [Documentation] Verify that nameservers obtained via Redfish do not ... match those found in /etc/resolv.conf. ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} ${redfish_nameservers}= Redfish.Get Attribute ... ${REDFISH_NW_ETH_IFACE}${ethernet_interface} StaticNameServers ${resolve_conf_nameservers}= CLI Get Nameservers Rqprint Vars redfish_nameservers resolve_conf_nameservers List Should Contain Sub List ${resolve_conf_nameservers} ${redfish_nameservers} ... msg=The nameservers obtained via Redfish do not match those found in /etc/resolv.conf. Configure Static Name Servers [Documentation] Configure DNS server on BMC. [Arguments] ${static_name_servers}=${original_nameservers} ... ${valid_status_codes}=${HTTP_OK} # Description of the argument(s): # static_name_servers A list of static name server IPs to be # configured on the BMC. ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} ${type} = Evaluate type($static_name_servers).__name__ ${static_name_servers}= Set Variable If '${type}'=='str' ... '${static_name_servers}' ${static_name_servers} # Currently BMC is sending 500 response code instead of 400 for invalid scenarios. Redfish.Patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface} ... body={'StaticNameServers': ${static_name_servers}} ... valid_status_codes=[${valid_status_codes}, ${HTTP_INTERNAL_SERVER_ERROR}] # Patch operation takes 1 to 3 seconds to set new value. Sleep 3s # Check if newly added DNS server is configured on BMC. ${cli_nameservers}= CLI Get Nameservers ${cmd_status}= Run Keyword And Return Status ... List Should Contain Sub List ${cli_nameservers} ${static_name_servers} Run Keyword If '${valid_status_codes}' == '${HTTP_OK}' ... Should Be True ${cmd_status} == ${True} ... ELSE Should Be True ${cmd_status} == ${False} Delete Static Name Servers [Documentation] Delete static name servers. Configure Static Name Servers static_name_servers=@{EMPTY} # Check if all name servers deleted on BMC. ${nameservers}= CLI Get Nameservers Should Be Empty ${nameservers} DNS Test Setup Execution [Documentation] Do DNS test setup execution. Redfish.Login ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} ${original_nameservers}= Redfish.Get Attribute ... ${REDFISH_NW_ETH_IFACE}${ethernet_interface} StaticNameServers Rprint Vars original_nameservers # Set suite variables to trigger restoration during teardown. Set Suite Variable ${original_nameservers} Suite Setup Execution [Documentation] Do suite setup execution. ${test_gateway}= Get BMC Default Gateway Set Suite Variable ${test_gateway} Update IP Address [Documentation] Update IP address of BMC. [Arguments] ${ip} ${new_ip} ${netmask} ${gw_ip} ... ${valid_status_codes}=[${HTTP_OK}, ${HTTP_NO_CONTENT}] # Description of argument(s): # ip IP address to be replaced (e.g. "10.7.7.7"). # new_ip New IP address to be configured. # netmask Netmask value. # gw_ip Gateway IP address. # valid_status_codes Expected return code from patch operation # (e.g. "200"). See prolog of rest_request # method in redfish_plus.py for details. ${empty_dict}= Create Dictionary ${patch_list}= Create List ${ip_data}= Create Dictionary Address=${new_ip} SubnetMask=${netmask} Gateway=${gw_ip} # Find the position of IP address to be modified. @{network_configurations}= Get Network Configuration FOR ${network_configuration} IN @{network_configurations} Run Keyword If '${network_configuration['Address']}' == '${ip}' ... Append To List ${patch_list} ${ip_data} ... ELSE Append To List ${patch_list} ${empty_dict} END ${ip_found}= Run Keyword And Return Status List Should Contain Value ... ${patch_list} ${ip_data} msg=${ip} does not exist on BMC Pass Execution If ${ip_found} == ${False} ${ip} does not exist on BMC # Run patch command only if given IP is found on BMC ${data}= Create Dictionary IPv4StaticAddresses=${patch_list} ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} Redfish.patch ${REDFISH_NW_ETH_IFACE}${ethernet_interface} ... body=&{data} valid_status_codes=${valid_status_codes} # Note: Network restart takes around 15-18s after patch request processing. Sleep ${NETWORK_TIMEOUT}s Wait For Host To Ping ${OPENBMC_HOST} ${NETWORK_TIMEOUT} Verify IP On BMC ${new_ip} Validate Network Config On BMC Configure Multiple Static IPv4 Addresses [Documentation] Configure multiple static ipv4 address via Redfish and verify. [Arguments] ${ip_addreses} ${subnet_mask} ${gateway} # Description of argument(s): # ip_addreses A list of IP addresses to be added (e.g.["10.7.7.7"]). # subnet_mask Subnet mask for the IP to be added (e.g. "255.255.0.0"). # gateway Gateway for the IP to be added (e.g. "10.7.7.1"). FOR ${ip} IN @{ip_addreses} Add IP Address ${ip} ${subnet_mask} ${gateway} END Validate Network Config On BMC Delete Multiple Static IPv4 Addresses [Documentation] Delete multiple static ipv4 address via Redfish. [Arguments] ${ip_addreses} # Description of argument(s): # ip_addreses A list of IP addresses to be deleted (e.g.["10.7.7.7"]). FOR ${ip} IN @{ip_addreses} Delete IP Address ${ip} END Validate Network Config On BMC Verify Network Response On Specified Host State [Documentation] Verifying the BMC network response when host is on and off. [Arguments] ${host_state} # Description of argument(s): # host_state if host_state is on then host is booted to operating system. # if host_state is off then host is power off. # (eg. on, off). ${active_channel_config}= Get Active Channel Config ${ethernet_interface}= Set Variable ${active_channel_config['${CHANNEL_NUMBER}']['name']} Run Keyword If '${host_state}' == 'on' ... Redfish Power On stack_mode=skip ... ELSE ... Redfish Power off stack_mode=skip Redfish.Get ${REDFISH_NW_ETH_IFACE}${ethernet_interface} Ping Host ${OPENBMC_HOST}