config STMMAC_ETH
	tristate "STMicroelectronics 10/100/1000 Ethernet driver"
	depends on HAS_IOMEM && HAS_DMA
	select MII
	select PHYLIB
	select CRC32
	select PTP_1588_CLOCK
	select RESET_CONTROLLER
	---help---
	  This is the driver for the Ethernet IPs are built around a
	  Synopsys IP Core and only tested on the STMicroelectronics
	  platforms.

if STMMAC_ETH

config STMMAC_PLATFORM
	tristate "STMMAC Platform bus support"
	depends on STMMAC_ETH
	default y
	---help---
	  This selects the platform specific bus support for the stmmac driver.
	  This is the driver used on several SoCs:
	  STi, Allwinner, Amlogic Meson, Altera SOCFPGA.

	  If you have a controller with this interface, say Y or M here.

	  If unsure, say N.

if STMMAC_PLATFORM

config DWMAC_GENERIC
	tristate "Generic driver for DWMAC"
	default STMMAC_PLATFORM
	---help---
	  Generic DWMAC driver for platforms that don't require any
	  platform specific code to function or is using platform
	  data for setup.

config DWMAC_LPC18XX
	tristate "NXP LPC18xx/43xx DWMAC support"
	default ARCH_LPC18XX
	depends on OF
	select MFD_SYSCON
	---help---
	  Support for NXP LPC18xx/43xx DWMAC Ethernet.

config DWMAC_MESON
	tristate "Amlogic Meson dwmac support"
	default ARCH_MESON
	depends on OF
	help
	  Support for Ethernet controller on Amlogic Meson SoCs.

	  This selects the Amlogic Meson SoC glue layer support for
	  the stmmac device driver. This driver is used for Meson6 and
	  Meson8 SoCs.

config DWMAC_ROCKCHIP
	tristate "Rockchip dwmac support"
	default ARCH_ROCKCHIP
	depends on OF
	select MFD_SYSCON
	help
	  Support for Ethernet controller on Rockchip RK3288 SoC.

	  This selects the Rockchip RK3288 SoC glue layer support for
	  the stmmac device driver.

config DWMAC_SOCFPGA
	tristate "SOCFPGA dwmac support"
	default ARCH_SOCFPGA
	depends on OF
	select MFD_SYSCON
	help
	  Support for ethernet controller on Altera SOCFPGA

	  This selects the Altera SOCFPGA SoC glue layer support
	  for the stmmac device driver. This driver is used for
	  arria5 and cyclone5 FPGA SoCs.

config DWMAC_STI
	tristate "STi GMAC support"
	default ARCH_STI
	depends on OF
	select MFD_SYSCON
	---help---
	  Support for ethernet controller on STi SOCs.

	  This selects STi SoC glue layer support for the stmmac
	  device driver. This driver is used on for the STi series
	  SOCs GMAC ethernet controller.

config DWMAC_SUNXI
	tristate "Allwinner GMAC support"
	default ARCH_SUNXI
	depends on OF
	---help---
	  Support for Allwinner A20/A31 GMAC ethernet controllers.

	  This selects Allwinner SoC glue layer support for the
	  stmmac device driver. This driver is used for A20/A31
	  GMAC ethernet controller.
endif

config STMMAC_PCI
	tristate "STMMAC PCI bus support"
	depends on STMMAC_ETH && PCI
	---help---
	  This is to select the Synopsys DWMAC available on PCI devices,
	  if you have a controller with this interface, say Y or M here.

	  This PCI support is tested on XLINX XC2V3000 FF1152AMT0221
	  D1215994A VIRTEX FPGA board.

	  If unsure, say N.
endif