# SPDX-License-Identifier: GPL-2.0-only # # Light sensors # # When adding new entries keep the list in alphabetical order menu "Light sensors" config ACPI_ALS tristate "ACPI Ambient Light Sensor" depends on ACPI select IIO_BUFFER select IIO_TRIGGERED_BUFFER select IIO_KFIFO_BUF help Say Y here if you want to build a driver for the ACPI0008 Ambient Light Sensor. To compile this driver as a module, choose M here: the module will be called acpi-als. config ADJD_S311 tristate "ADJD-S311-CR999 digital color sensor" select IIO_BUFFER select IIO_TRIGGERED_BUFFER depends on I2C help If you say yes here you get support for the Avago ADJD-S311-CR999 digital color light sensor. This driver can also be built as a module. If so, the module will be called adjd_s311. config ADUX1020 tristate "ADUX1020 photometric sensor" select REGMAP_I2C depends on I2C help Say Y here if you want to build a driver for the Analog Devices ADUX1020 photometric sensor. To compile this driver as a module, choose M here: the module will be called adux1020. config AL3010 tristate "AL3010 ambient light sensor" depends on I2C help Say Y here if you want to build a driver for the Dyna Image AL3010 ambient light sensor. To compile this driver as a module, choose M here: the module will be called al3010. config AL3320A tristate "AL3320A ambient light sensor" depends on I2C help Say Y here if you want to build a driver for the Dyna Image AL3320A ambient light sensor. To compile this driver as a module, choose M here: the module will be called al3320a. config APDS9300 tristate "APDS9300 ambient light sensor" depends on I2C help Say Y here if you want to build a driver for the Avago APDS9300 ambient light sensor. To compile this driver as a module, choose M here: the module will be called apds9300. config APDS9960 tristate "Avago APDS9960 gesture/RGB/ALS/proximity sensor" select REGMAP_I2C select IIO_BUFFER select IIO_KFIFO_BUF depends on I2C help Say Y here to build I2C interface support for the Avago APDS9960 gesture/RGB/ALS/proximity sensor. To compile this driver as a module, choose M here: the module will be called apds9960 config AS73211 tristate "AMS AS73211 XYZ color sensor" depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help If you say yes here you get support for the AMS AS73211 JENCOLOR(R) Digital XYZ Sensor. For triggered measurements, you will need an additional trigger driver like IIO_HRTIMER_TRIGGER or IIO_SYSFS_TRIGGER. This driver can also be built as a module. If so, the module will be called as73211. config BH1750 tristate "ROHM BH1750 ambient light sensor" depends on I2C help Say Y here to build support for the ROHM BH1710, BH1715, BH1721, BH1750, BH1751 ambient light sensors. To compile this driver as a module, choose M here: the module will be called bh1750. config BH1780 tristate "ROHM BH1780 ambient light sensor" depends on I2C help Say Y here to build support for the ROHM BH1780GLI ambient light sensor. To compile this driver as a module, choose M here: the module will be called bh1780. config CM32181 depends on I2C tristate "CM32181 driver" help Say Y here if you use cm32181. This option enables ambient light sensor using Capella cm32181 device driver. To compile this driver as a module, choose M here: the module will be called cm32181. config CM3232 depends on I2C tristate "CM3232 ambient light sensor" help Say Y here if you use cm3232. This option enables ambient light sensor using Capella Microsystems cm3232 device driver. To compile this driver as a module, choose M here: the module will be called cm3232. config CM3323 depends on I2C tristate "Capella CM3323 color light sensor" help Say Y here if you want to build a driver for Capella CM3323 color sensor. To compile this driver as a module, choose M here: the module will be called cm3323. config CM3605 tristate "Capella CM3605 ambient light and proximity sensor" help Say Y here if you want to build a driver for Capella CM3605 ambient light and short range proximity sensor. To compile this driver as a module, choose M here: the module will be called cm3605. config CM36651 depends on I2C tristate "CM36651 driver" help Say Y here if you use cm36651. This option enables proximity & RGB sensor using Capella cm36651 device driver. To compile this driver as a module, choose M here: the module will be called cm36651. config IIO_CROS_EC_LIGHT_PROX tristate "ChromeOS EC Light and Proximity Sensors" depends on IIO_CROS_EC_SENSORS_CORE help Say Y here if you use the light and proximity sensors presented by the ChromeOS EC Sensor hub. To compile this driver as a module, choose M here: the module will be called cros_ec_light_prox. config GP2AP002 tristate "Sharp GP2AP002 Proximity/ALS sensor" depends on I2C select REGMAP help Say Y here if you have a Sharp GP2AP002 proximity/ALS combo-chip hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called gp2ap002. config GP2AP020A00F tristate "Sharp GP2AP020A00F Proximity/ALS sensor" depends on I2C select REGMAP_I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER select IRQ_WORK help Say Y here if you have a Sharp GP2AP020A00F proximity/ALS combo-chip hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called gp2ap020a00f. config IQS621_ALS tristate "Azoteq IQS621/622 ambient light sensors" depends on MFD_IQS62X || COMPILE_TEST help Say Y here if you want to build support for the Azoteq IQS621 and IQS622 ambient light sensors. To compile this driver as a module, choose M here: the module will be called iqs621-als. config SENSORS_ISL29018 tristate "Intersil 29018 light and proximity sensor" depends on I2C select REGMAP_I2C default n help If you say yes here you get support for ambient light sensing and proximity infrared sensing from Intersil ISL29018. This driver will provide the measurements of ambient light intensity in lux, proximity infrared sensing and normal infrared sensing. Data from sensor is accessible via sysfs. config SENSORS_ISL29028 tristate "Intersil ISL29028 Concurrent Light and Proximity Sensor" depends on I2C select REGMAP_I2C help Provides driver for the Intersil's ISL29028 device. This driver supports the sysfs interface to get the ALS, IR intensity, Proximity value via iio. The ISL29028 provides the concurrent sensing of ambient light and proximity. config ISL29125 tristate "Intersil ISL29125 digital color light sensor" depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help Say Y here if you want to build a driver for the Intersil ISL29125 RGB light sensor for I2C. To compile this driver as a module, choose M here: the module will be called isl29125. config HID_SENSOR_ALS depends on HID_SENSOR_HUB select IIO_BUFFER select HID_SENSOR_IIO_COMMON select HID_SENSOR_IIO_TRIGGER tristate "HID ALS" help Say yes here to build support for the HID SENSOR Ambient light sensor. To compile this driver as a module, choose M here: the module will be called hid-sensor-als. config HID_SENSOR_PROX depends on HID_SENSOR_HUB select IIO_BUFFER select HID_SENSOR_IIO_COMMON select HID_SENSOR_IIO_TRIGGER tristate "HID PROX" help Say yes here to build support for the HID SENSOR Proximity sensor. To compile this driver as a module, choose M here: the module will be called hid-sensor-prox. config JSA1212 tristate "JSA1212 ALS and proximity sensor driver" depends on I2C select REGMAP_I2C help Say Y here if you want to build a IIO driver for JSA1212 proximity & ALS sensor device. To compile this driver as a module, choose M here: the module will be called jsa1212. config ROHM_BU27008 tristate "ROHM BU27008 color (RGB+C/IR) sensor" depends on I2C select REGMAP_I2C select IIO_GTS_HELPER select IIO_BUFFER select IIO_TRIGGERED_BUFFER help Enable support for the ROHM BU27008 color sensor. The ROHM BU27008 is a sensor with 5 photodiodes (red, green, blue, clear and IR) with four configurable channels. Red and green being always available and two out of the rest three (blue, clear, IR) can be selected to be simultaneously measured. Typical application is adjusting LCD backlight of TVs, mobile phones and tablet PCs. config ROHM_BU27034 tristate "ROHM BU27034 ambient light sensor" depends on I2C select REGMAP_I2C select IIO_GTS_HELPER select IIO_BUFFER select IIO_KFIFO_BUF help Enable support for the ROHM BU27034 ambient light sensor. ROHM BU27034 is an ambient light sesnor with 3 channels and 3 photo diodes capable of detecting a very wide range of illuminance. Typical application is adjusting LCD and backlight power of TVs and mobile phones. config RPR0521 tristate "ROHM RPR0521 ALS and proximity sensor driver" depends on I2C select REGMAP_I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help Say Y here if you want to build support for ROHM's RPR0521 ambient light and proximity sensor device. To compile this driver as a module, choose M here: the module will be called rpr0521. config SENSORS_LM3533 tristate "LM3533 ambient light sensor" depends on MFD_LM3533 help If you say yes here you get support for the ambient light sensor interface on National Semiconductor / TI LM3533 Lighting Power chips. The sensor interface can be used to control the LEDs and backlights of the chip through defining five light zones and three sets of corresponding output-current values. The driver provides raw and mean adc readings along with the current light zone through sysfs. A threshold event can be generated on zone changes. The ALS-control output values can be set per zone for the three current output channels. config LTR501 tristate "LTR-501ALS-01 light sensor" depends on I2C select REGMAP_I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help If you say yes here you get support for the Lite-On LTR-501ALS-01 ambient light and proximity sensor. This driver also supports LTR-559 ALS/PS or LTR-301 ALS sensors. This driver can also be built as a module. If so, the module will be called ltr501. config LTRF216A tristate "Liteon LTRF216A Light Sensor" depends on I2C select REGMAP_I2C help If you say Y or M here, you get support for Liteon LTRF216A Ambient Light Sensor. If built as a dynamically linked module, it will be called ltrf216a. config LV0104CS tristate "LV0104CS Ambient Light Sensor" depends on I2C help Say Y here if you want to build support for the On Semiconductor LV0104CS ambient light sensor. To compile this driver as a module, choose M here: the module will be called lv0104cs. config MAX44000 tristate "MAX44000 Ambient and Infrared Proximity Sensor" depends on I2C select REGMAP_I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help Say Y here if you want to build support for Maxim Integrated's MAX44000 ambient and infrared proximity sensor device. To compile this driver as a module, choose M here: the module will be called max44000. config MAX44009 tristate "MAX44009 Ambient Light Sensor" depends on I2C select REGMAP_I2C help Say Y here if you want to build support for Maxim Integrated's MAX44009 ambient light sensor device. To compile this driver as a module, choose M here: the module will be called max44009. config NOA1305 tristate "ON Semiconductor NOA1305 ambient light sensor" depends on I2C select REGMAP_I2C help Say Y here if you want to build support for the ON Semiconductor NOA1305 ambient light sensor. To compile this driver as a module, choose M here: The module will be called noa1305. config OPT3001 tristate "Texas Instruments OPT3001 Light Sensor" depends on I2C help If you say Y or M here, you get support for Texas Instruments OPT3001 Ambient Light Sensor. If built as a dynamically linked module, it will be called opt3001. config OPT4001 tristate "Texas Instruments OPT4001 Light Sensor" depends on I2C select REGMAP_I2C help If you say Y or M here, you get support for Texas Instruments OPT4001 Ambient Light Sensor. If built as a dynamically linked module, it will be called opt4001. config PA12203001 tristate "TXC PA12203001 light and proximity sensor" depends on I2C select REGMAP_I2C help If you say yes here you get support for the TXC PA12203001 ambient light and proximity sensor. This driver can also be built as a module. If so, the module will be called pa12203001. config SI1133 tristate "SI1133 UV Index Sensor and Ambient Light Sensor" depends on I2C select REGMAP_I2C help Say Y here if you want to build a driver for the Silicon Labs SI1133 UV Index Sensor and Ambient Light Sensor chip. To compile this driver as a module, choose M here: the module will be called si1133. config SI1145 tristate "SI1132 and SI1141/2/3/5/6/7 combined ALS, UV index and proximity sensor" depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help Say Y here if you want to build a driver for the Silicon Labs SI1132 or SI1141/2/3/5/6/7 combined ambient light, UV index and proximity sensor chips. To compile this driver as a module, choose M here: the module will be called si1145. config STK3310 tristate "STK3310 ALS and proximity sensor" depends on I2C select REGMAP_I2C help Say yes here to get support for the Sensortek STK3310 ambient light and proximity sensor. The STK3311 model is also supported by this driver. Choosing M will build the driver as a module. If so, the module will be called stk3310. config ST_UVIS25 tristate "STMicroelectronics UVIS25 sensor driver" depends on (I2C || SPI) select IIO_BUFFER select IIO_TRIGGERED_BUFFER select ST_UVIS25_I2C if (I2C) select ST_UVIS25_SPI if (SPI_MASTER) help Say yes here to build support for STMicroelectronics UVIS25 uv sensor To compile this driver as a module, choose M here: the module will be called st_uvis25. config ST_UVIS25_I2C tristate depends on ST_UVIS25 select REGMAP_I2C config ST_UVIS25_SPI tristate depends on ST_UVIS25 select REGMAP_SPI config TCS3414 tristate "TAOS TCS3414 digital color sensor" depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help If you say yes here you get support for the TAOS TCS3414 family of digital color sensors. This driver can also be built as a module. If so, the module will be called tcs3414. config TCS3472 tristate "TAOS TCS3472 color light-to-digital converter" depends on I2C select IIO_BUFFER select IIO_TRIGGERED_BUFFER help If you say yes here you get support for the TAOS TCS3472 family of color light-to-digital converters with IR filter. This driver can also be built as a module. If so, the module will be called tcs3472. config SENSORS_TSL2563 tristate "TAOS TSL2560, TSL2561, TSL2562 and TSL2563 ambient light sensors" depends on I2C help If you say yes here you get support for the Taos TSL2560, TSL2561, TSL2562 and TSL2563 ambient light sensors. This driver can also be built as a module. If so, the module will be called tsl2563. config TSL2583 tristate "TAOS TSL2580, TSL2581 and TSL2583 light-to-digital converters" depends on I2C help Provides support for the TAOS tsl2580, tsl2581 and tsl2583 devices. Access ALS data via iio, sysfs. config TSL2591 tristate "TAOS TSL2591 ambient light sensor" depends on I2C help Select Y here for support of the AMS/TAOS TSL2591 ambient light sensor, featuring channels for combined visible + IR intensity and lux illuminance. Access data via iio and sysfs. Supports iio_events. To compile this driver as a module, select M: the module will be called tsl2591. config TSL2772 tristate "TAOS TSL/TMD2x71 and TSL/TMD2x72 Family of light and proximity sensors" depends on I2C help Support for: tsl2571, tsl2671, tmd2671, tsl2771, tmd2771, tsl2572, tsl2672, tmd2672, tsl2772, tmd2772 devices. Provides iio_events and direct access via sysfs. config TSL4531 tristate "TAOS TSL4531 ambient light sensors" depends on I2C help Say Y here if you want to build a driver for the TAOS TSL4531 family of ambient light sensors with direct lux output. To compile this driver as a module, choose M here: the module will be called tsl4531. config US5182D tristate "UPISEMI light and proximity sensor" depends on I2C help If you say yes here you get support for the UPISEMI US5182D ambient light and proximity sensor. This driver can also be built as a module. If so, the module will be called us5182d. config VCNL4000 tristate "VCNL4000/4010/4020/4200 combined ALS and proximity sensor" select IIO_BUFFER select IIO_TRIGGERED_BUFFER depends on I2C help Say Y here if you want to build a driver for the Vishay VCNL4000, VCNL4010, VCNL4020, VCNL4200 combined ambient light and proximity sensor. To compile this driver as a module, choose M here: the module will be called vcnl4000. config VCNL4035 tristate "VCNL4035 combined ALS and proximity sensor" select IIO_BUFFER select IIO_TRIGGERED_BUFFER select REGMAP_I2C depends on I2C help Say Y here if you want to build a driver for the Vishay VCNL4035, combined ambient light (ALS) and proximity sensor. Currently only ALS function is available. To compile this driver as a module, choose M here: the module will be called vcnl4035. config VEML6030 tristate "VEML6030 ambient light sensor" select REGMAP_I2C depends on I2C help Say Y here if you want to build a driver for the Vishay VEML6030 ambient light sensor (ALS). To compile this driver as a module, choose M here: the module will be called veml6030. config VEML6070 tristate "VEML6070 UV A light sensor" depends on I2C help Say Y here if you want to build a driver for the Vishay VEML6070 UV A light sensor. To compile this driver as a module, choose M here: the module will be called veml6070. config VL6180 tristate "VL6180 ALS, range and proximity sensor" depends on I2C help Say Y here if you want to build a driver for the STMicroelectronics VL6180 combined ambient light, range and proximity sensor. To compile this driver as a module, choose M here: the module will be called vl6180. config ZOPT2201 tristate "ZOPT2201 ALS and UV B sensor" depends on I2C help Say Y here if you want to build a driver for the IDT ZOPT2201 ambient light and UV B sensor. To compile this driver as a module, choose M here: the module will be called zopt2201. endmenu