// SPDX-License-Identifier: GPL-2.0+ /* * BCM2835 DMA engine support * * Author: Florian Meier * Copyright 2013 * * Based on * OMAP DMAengine support by Russell King * * BCM2708 DMA Driver * Copyright (C) 2010 Broadcom * * Raspberry Pi PCM I2S ALSA Driver * Copyright (c) by Phil Poole 2013 * * MARVELL MMP Peripheral DMA Driver * Copyright 2012 Marvell International Ltd. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "virt-dma.h" #define BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED 14 #define BCM2835_DMA_CHAN_NAME_SIZE 8 struct bcm2835_dmadev { struct dma_device ddev; void __iomem *base; struct device_dma_parameters dma_parms; }; struct bcm2835_dma_cb { uint32_t info; uint32_t src; uint32_t dst; uint32_t length; uint32_t stride; uint32_t next; uint32_t pad[2]; }; struct bcm2835_cb_entry { struct bcm2835_dma_cb *cb; dma_addr_t paddr; }; struct bcm2835_chan { struct virt_dma_chan vc; struct dma_slave_config cfg; unsigned int dreq; int ch; struct bcm2835_desc *desc; struct dma_pool *cb_pool; void __iomem *chan_base; int irq_number; unsigned int irq_flags; bool is_lite_channel; }; struct bcm2835_desc { struct bcm2835_chan *c; struct virt_dma_desc vd; enum dma_transfer_direction dir; unsigned int frames; size_t size; bool cyclic; struct bcm2835_cb_entry cb_list[]; }; #define BCM2835_DMA_CS 0x00 #define BCM2835_DMA_ADDR 0x04 #define BCM2835_DMA_TI 0x08 #define BCM2835_DMA_SOURCE_AD 0x0c #define BCM2835_DMA_DEST_AD 0x10 #define BCM2835_DMA_LEN 0x14 #define BCM2835_DMA_STRIDE 0x18 #define BCM2835_DMA_NEXTCB 0x1c #define BCM2835_DMA_DEBUG 0x20 /* DMA CS Control and Status bits */ #define BCM2835_DMA_ACTIVE BIT(0) /* activate the DMA */ #define BCM2835_DMA_END BIT(1) /* current CB has ended */ #define BCM2835_DMA_INT BIT(2) /* interrupt status */ #define BCM2835_DMA_DREQ BIT(3) /* DREQ state */ #define BCM2835_DMA_ISPAUSED BIT(4) /* Pause requested or not active */ #define BCM2835_DMA_ISHELD BIT(5) /* Is held by DREQ flow control */ #define BCM2835_DMA_WAITING_FOR_WRITES BIT(6) /* waiting for last * AXI-write to ack */ #define BCM2835_DMA_ERR BIT(8) #define BCM2835_DMA_PRIORITY(x) ((x & 15) << 16) /* AXI priority */ #define BCM2835_DMA_PANIC_PRIORITY(x) ((x & 15) << 20) /* panic priority */ /* current value of TI.BCM2835_DMA_WAIT_RESP */ #define BCM2835_DMA_WAIT_FOR_WRITES BIT(28) #define BCM2835_DMA_DIS_DEBUG BIT(29) /* disable debug pause signal */ #define BCM2835_DMA_ABORT BIT(30) /* Stop current CB, go to next, WO */ #define BCM2835_DMA_RESET BIT(31) /* WO, self clearing */ /* Transfer information bits - also bcm2835_cb.info field */ #define BCM2835_DMA_INT_EN BIT(0) #define BCM2835_DMA_TDMODE BIT(1) /* 2D-Mode */ #define BCM2835_DMA_WAIT_RESP BIT(3) /* wait for AXI-write to be acked */ #define BCM2835_DMA_D_INC BIT(4) #define BCM2835_DMA_D_WIDTH BIT(5) /* 128bit writes if set */ #define BCM2835_DMA_D_DREQ BIT(6) /* enable DREQ for destination */ #define BCM2835_DMA_D_IGNORE BIT(7) /* ignore destination writes */ #define BCM2835_DMA_S_INC BIT(8) #define BCM2835_DMA_S_WIDTH BIT(9) /* 128bit writes if set */ #define BCM2835_DMA_S_DREQ BIT(10) /* enable SREQ for source */ #define BCM2835_DMA_S_IGNORE BIT(11) /* ignore source reads - read 0 */ #define BCM2835_DMA_BURST_LENGTH(x) ((x & 15) << 12) #define BCM2835_DMA_PER_MAP(x) ((x & 31) << 16) /* REQ source */ #define BCM2835_DMA_WAIT(x) ((x & 31) << 21) /* add DMA-wait cycles */ #define BCM2835_DMA_NO_WIDE_BURSTS BIT(26) /* no 2 beat write bursts */ /* debug register bits */ #define BCM2835_DMA_DEBUG_LAST_NOT_SET_ERR BIT(0) #define BCM2835_DMA_DEBUG_FIFO_ERR BIT(1) #define BCM2835_DMA_DEBUG_READ_ERR BIT(2) #define BCM2835_DMA_DEBUG_OUTSTANDING_WRITES_SHIFT 4 #define BCM2835_DMA_DEBUG_OUTSTANDING_WRITES_BITS 4 #define BCM2835_DMA_DEBUG_ID_SHIFT 16 #define BCM2835_DMA_DEBUG_ID_BITS 9 #define BCM2835_DMA_DEBUG_STATE_SHIFT 16 #define BCM2835_DMA_DEBUG_STATE_BITS 9 #define BCM2835_DMA_DEBUG_VERSION_SHIFT 25 #define BCM2835_DMA_DEBUG_VERSION_BITS 3 #define BCM2835_DMA_DEBUG_LITE BIT(28) /* shared registers for all dma channels */ #define BCM2835_DMA_INT_STATUS 0xfe0 #define BCM2835_DMA_ENABLE 0xff0 #define BCM2835_DMA_DATA_TYPE_S8 1 #define BCM2835_DMA_DATA_TYPE_S16 2 #define BCM2835_DMA_DATA_TYPE_S32 4 #define BCM2835_DMA_DATA_TYPE_S128 16 /* Valid only for channels 0 - 14, 15 has its own base address */ #define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */ #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n)) /* the max dma length for different channels */ #define MAX_DMA_LEN SZ_1G #define MAX_LITE_DMA_LEN (SZ_64K - 4) static inline size_t bcm2835_dma_max_frame_length(struct bcm2835_chan *c) { /* lite and normal channels have different max frame length */ return c->is_lite_channel ? MAX_LITE_DMA_LEN : MAX_DMA_LEN; } /* how many frames of max_len size do we need to transfer len bytes */ static inline size_t bcm2835_dma_frames_for_length(size_t len, size_t max_len) { return DIV_ROUND_UP(len, max_len); } static inline struct bcm2835_dmadev *to_bcm2835_dma_dev(struct dma_device *d) { return container_of(d, struct bcm2835_dmadev, ddev); } static inline struct bcm2835_chan *to_bcm2835_dma_chan(struct dma_chan *c) { return container_of(c, struct bcm2835_chan, vc.chan); } static inline struct bcm2835_desc *to_bcm2835_dma_desc( struct dma_async_tx_descriptor *t) { return container_of(t, struct bcm2835_desc, vd.tx); } static void bcm2835_dma_free_cb_chain(struct bcm2835_desc *desc) { size_t i; for (i = 0; i < desc->frames; i++) dma_pool_free(desc->c->cb_pool, desc->cb_list[i].cb, desc->cb_list[i].paddr); kfree(desc); } static void bcm2835_dma_desc_free(struct virt_dma_desc *vd) { bcm2835_dma_free_cb_chain( container_of(vd, struct bcm2835_desc, vd)); } static void bcm2835_dma_create_cb_set_length( struct bcm2835_chan *chan, struct bcm2835_dma_cb *control_block, size_t len, size_t period_len, size_t *total_len, u32 finalextrainfo) { size_t max_len = bcm2835_dma_max_frame_length(chan); /* set the length taking lite-channel limitations into account */ control_block->length = min_t(u32, len, max_len); /* finished if we have no period_length */ if (!period_len) return; /* * period_len means: that we need to generate * transfers that are terminating at every * multiple of period_len - this is typically * used to set the interrupt flag in info * which is required during cyclic transfers */ /* have we filled in period_length yet? */ if (*total_len + control_block->length < period_len) { /* update number of bytes in this period so far */ *total_len += control_block->length; return; } /* calculate the length that remains to reach period_length */ control_block->length = period_len - *total_len; /* reset total_length for next period */ *total_len = 0; /* add extrainfo bits in info */ control_block->info |= finalextrainfo; } static inline size_t bcm2835_dma_count_frames_for_sg( struct bcm2835_chan *c, struct scatterlist *sgl, unsigned int sg_len) { size_t frames = 0; struct scatterlist *sgent; unsigned int i; size_t plength = bcm2835_dma_max_frame_length(c); for_each_sg(sgl, sgent, sg_len, i) frames += bcm2835_dma_frames_for_length( sg_dma_len(sgent), plength); return frames; } /** * bcm2835_dma_create_cb_chain - create a control block and fills data in * * @chan: the @dma_chan for which we run this * @direction: the direction in which we transfer * @cyclic: it is a cyclic transfer * @info: the default info bits to apply per controlblock * @frames: number of controlblocks to allocate * @src: the src address to assign (if the S_INC bit is set * in @info, then it gets incremented) * @dst: the dst address to assign (if the D_INC bit is set * in @info, then it gets incremented) * @buf_len: the full buffer length (may also be 0) * @period_len: the period length when to apply @finalextrainfo * in addition to the last transfer * this will also break some control-blocks early * @finalextrainfo: additional bits in last controlblock * (or when period_len is reached in case of cyclic) * @gfp: the GFP flag to use for allocation */ static struct bcm2835_desc *bcm2835_dma_create_cb_chain( struct dma_chan *chan, enum dma_transfer_direction direction, bool cyclic, u32 info, u32 finalextrainfo, size_t frames, dma_addr_t src, dma_addr_t dst, size_t buf_len, size_t period_len, gfp_t gfp) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); size_t len = buf_len, total_len; size_t frame; struct bcm2835_desc *d; struct bcm2835_cb_entry *cb_entry; struct bcm2835_dma_cb *control_block; if (!frames) return NULL; /* allocate and setup the descriptor. */ d = kzalloc(struct_size(d, cb_list, frames), gfp); if (!d) return NULL; d->c = c; d->dir = direction; d->cyclic = cyclic; /* * Iterate over all frames, create a control block * for each frame and link them together. */ for (frame = 0, total_len = 0; frame < frames; d->frames++, frame++) { cb_entry = &d->cb_list[frame]; cb_entry->cb = dma_pool_alloc(c->cb_pool, gfp, &cb_entry->paddr); if (!cb_entry->cb) goto error_cb; /* fill in the control block */ control_block = cb_entry->cb; control_block->info = info; control_block->src = src; control_block->dst = dst; control_block->stride = 0; control_block->next = 0; /* set up length in control_block if requested */ if (buf_len) { /* calculate length honoring period_length */ bcm2835_dma_create_cb_set_length( c, control_block, len, period_len, &total_len, cyclic ? finalextrainfo : 0); /* calculate new remaining length */ len -= control_block->length; } /* link this the last controlblock */ if (frame) d->cb_list[frame - 1].cb->next = cb_entry->paddr; /* update src and dst and length */ if (src && (info & BCM2835_DMA_S_INC)) src += control_block->length; if (dst && (info & BCM2835_DMA_D_INC)) dst += control_block->length; /* Length of total transfer */ d->size += control_block->length; } /* the last frame requires extra flags */ d->cb_list[d->frames - 1].cb->info |= finalextrainfo; /* detect a size missmatch */ if (buf_len && (d->size != buf_len)) goto error_cb; return d; error_cb: bcm2835_dma_free_cb_chain(d); return NULL; } static void bcm2835_dma_fill_cb_chain_with_sg( struct dma_chan *chan, enum dma_transfer_direction direction, struct bcm2835_cb_entry *cb, struct scatterlist *sgl, unsigned int sg_len) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); size_t len, max_len; unsigned int i; dma_addr_t addr; struct scatterlist *sgent; max_len = bcm2835_dma_max_frame_length(c); for_each_sg(sgl, sgent, sg_len, i) { for (addr = sg_dma_address(sgent), len = sg_dma_len(sgent); len > 0; addr += cb->cb->length, len -= cb->cb->length, cb++) { if (direction == DMA_DEV_TO_MEM) cb->cb->dst = addr; else cb->cb->src = addr; cb->cb->length = min(len, max_len); } } } static void bcm2835_dma_abort(struct bcm2835_chan *c) { void __iomem *chan_base = c->chan_base; long int timeout = 10000; /* * A zero control block address means the channel is idle. * (The ACTIVE flag in the CS register is not a reliable indicator.) */ if (!readl(chan_base + BCM2835_DMA_ADDR)) return; /* Write 0 to the active bit - Pause the DMA */ writel(0, chan_base + BCM2835_DMA_CS); /* Wait for any current AXI transfer to complete */ while ((readl(chan_base + BCM2835_DMA_CS) & BCM2835_DMA_WAITING_FOR_WRITES) && --timeout) cpu_relax(); /* Peripheral might be stuck and fail to signal AXI write responses */ if (!timeout) dev_err(c->vc.chan.device->dev, "failed to complete outstanding writes\n"); writel(BCM2835_DMA_RESET, chan_base + BCM2835_DMA_CS); } static void bcm2835_dma_start_desc(struct bcm2835_chan *c) { struct virt_dma_desc *vd = vchan_next_desc(&c->vc); struct bcm2835_desc *d; if (!vd) { c->desc = NULL; return; } list_del(&vd->node); c->desc = d = to_bcm2835_dma_desc(&vd->tx); writel(d->cb_list[0].paddr, c->chan_base + BCM2835_DMA_ADDR); writel(BCM2835_DMA_ACTIVE, c->chan_base + BCM2835_DMA_CS); } static irqreturn_t bcm2835_dma_callback(int irq, void *data) { struct bcm2835_chan *c = data; struct bcm2835_desc *d; unsigned long flags; /* check the shared interrupt */ if (c->irq_flags & IRQF_SHARED) { /* check if the interrupt is enabled */ flags = readl(c->chan_base + BCM2835_DMA_CS); /* if not set then we are not the reason for the irq */ if (!(flags & BCM2835_DMA_INT)) return IRQ_NONE; } spin_lock_irqsave(&c->vc.lock, flags); /* * Clear the INT flag to receive further interrupts. Keep the channel * active in case the descriptor is cyclic or in case the client has * already terminated the descriptor and issued a new one. (May happen * if this IRQ handler is threaded.) If the channel is finished, it * will remain idle despite the ACTIVE flag being set. */ writel(BCM2835_DMA_INT | BCM2835_DMA_ACTIVE, c->chan_base + BCM2835_DMA_CS); d = c->desc; if (d) { if (d->cyclic) { /* call the cyclic callback */ vchan_cyclic_callback(&d->vd); } else if (!readl(c->chan_base + BCM2835_DMA_ADDR)) { vchan_cookie_complete(&c->desc->vd); bcm2835_dma_start_desc(c); } } spin_unlock_irqrestore(&c->vc.lock, flags); return IRQ_HANDLED; } static int bcm2835_dma_alloc_chan_resources(struct dma_chan *chan) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); struct device *dev = c->vc.chan.device->dev; dev_dbg(dev, "Allocating DMA channel %d\n", c->ch); /* * Control blocks are 256 bit in length and must start at a 256 bit * (32 byte) aligned address (BCM2835 ARM Peripherals, sec. 4.2.1.1). */ c->cb_pool = dma_pool_create(dev_name(dev), dev, sizeof(struct bcm2835_dma_cb), 32, 0); if (!c->cb_pool) { dev_err(dev, "unable to allocate descriptor pool\n"); return -ENOMEM; } return request_irq(c->irq_number, bcm2835_dma_callback, c->irq_flags, "DMA IRQ", c); } static void bcm2835_dma_free_chan_resources(struct dma_chan *chan) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); vchan_free_chan_resources(&c->vc); free_irq(c->irq_number, c); dma_pool_destroy(c->cb_pool); dev_dbg(c->vc.chan.device->dev, "Freeing DMA channel %u\n", c->ch); } static size_t bcm2835_dma_desc_size(struct bcm2835_desc *d) { return d->size; } static size_t bcm2835_dma_desc_size_pos(struct bcm2835_desc *d, dma_addr_t addr) { unsigned int i; size_t size; for (size = i = 0; i < d->frames; i++) { struct bcm2835_dma_cb *control_block = d->cb_list[i].cb; size_t this_size = control_block->length; dma_addr_t dma; if (d->dir == DMA_DEV_TO_MEM) dma = control_block->dst; else dma = control_block->src; if (size) size += this_size; else if (addr >= dma && addr < dma + this_size) size += dma + this_size - addr; } return size; } static enum dma_status bcm2835_dma_tx_status(struct dma_chan *chan, dma_cookie_t cookie, struct dma_tx_state *txstate) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); struct virt_dma_desc *vd; enum dma_status ret; unsigned long flags; ret = dma_cookie_status(chan, cookie, txstate); if (ret == DMA_COMPLETE || !txstate) return ret; spin_lock_irqsave(&c->vc.lock, flags); vd = vchan_find_desc(&c->vc, cookie); if (vd) { txstate->residue = bcm2835_dma_desc_size(to_bcm2835_dma_desc(&vd->tx)); } else if (c->desc && c->desc->vd.tx.cookie == cookie) { struct bcm2835_desc *d = c->desc; dma_addr_t pos; if (d->dir == DMA_MEM_TO_DEV) pos = readl(c->chan_base + BCM2835_DMA_SOURCE_AD); else if (d->dir == DMA_DEV_TO_MEM) pos = readl(c->chan_base + BCM2835_DMA_DEST_AD); else pos = 0; txstate->residue = bcm2835_dma_desc_size_pos(d, pos); } else { txstate->residue = 0; } spin_unlock_irqrestore(&c->vc.lock, flags); return ret; } static void bcm2835_dma_issue_pending(struct dma_chan *chan) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); unsigned long flags; spin_lock_irqsave(&c->vc.lock, flags); if (vchan_issue_pending(&c->vc) && !c->desc) bcm2835_dma_start_desc(c); spin_unlock_irqrestore(&c->vc.lock, flags); } static struct dma_async_tx_descriptor *bcm2835_dma_prep_dma_memcpy( struct dma_chan *chan, dma_addr_t dst, dma_addr_t src, size_t len, unsigned long flags) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); struct bcm2835_desc *d; u32 info = BCM2835_DMA_D_INC | BCM2835_DMA_S_INC; u32 extra = BCM2835_DMA_INT_EN | BCM2835_DMA_WAIT_RESP; size_t max_len = bcm2835_dma_max_frame_length(c); size_t frames; /* if src, dst or len is not given return with an error */ if (!src || !dst || !len) return NULL; /* calculate number of frames */ frames = bcm2835_dma_frames_for_length(len, max_len); /* allocate the CB chain - this also fills in the pointers */ d = bcm2835_dma_create_cb_chain(chan, DMA_MEM_TO_MEM, false, info, extra, frames, src, dst, len, 0, GFP_KERNEL); if (!d) return NULL; return vchan_tx_prep(&c->vc, &d->vd, flags); } static struct dma_async_tx_descriptor *bcm2835_dma_prep_slave_sg( struct dma_chan *chan, struct scatterlist *sgl, unsigned int sg_len, enum dma_transfer_direction direction, unsigned long flags, void *context) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); struct bcm2835_desc *d; dma_addr_t src = 0, dst = 0; u32 info = BCM2835_DMA_WAIT_RESP; u32 extra = BCM2835_DMA_INT_EN; size_t frames; if (!is_slave_direction(direction)) { dev_err(chan->device->dev, "%s: bad direction?\n", __func__); return NULL; } if (c->dreq != 0) info |= BCM2835_DMA_PER_MAP(c->dreq); if (direction == DMA_DEV_TO_MEM) { if (c->cfg.src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) return NULL; src = c->cfg.src_addr; info |= BCM2835_DMA_S_DREQ | BCM2835_DMA_D_INC; } else { if (c->cfg.dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) return NULL; dst = c->cfg.dst_addr; info |= BCM2835_DMA_D_DREQ | BCM2835_DMA_S_INC; } /* count frames in sg list */ frames = bcm2835_dma_count_frames_for_sg(c, sgl, sg_len); /* allocate the CB chain */ d = bcm2835_dma_create_cb_chain(chan, direction, false, info, extra, frames, src, dst, 0, 0, GFP_NOWAIT); if (!d) return NULL; /* fill in frames with scatterlist pointers */ bcm2835_dma_fill_cb_chain_with_sg(chan, direction, d->cb_list, sgl, sg_len); return vchan_tx_prep(&c->vc, &d->vd, flags); } static struct dma_async_tx_descriptor *bcm2835_dma_prep_dma_cyclic( struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len, size_t period_len, enum dma_transfer_direction direction, unsigned long flags) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); struct bcm2835_desc *d; dma_addr_t src, dst; u32 info = BCM2835_DMA_WAIT_RESP; u32 extra = BCM2835_DMA_INT_EN; size_t max_len = bcm2835_dma_max_frame_length(c); size_t frames; /* Grab configuration */ if (!is_slave_direction(direction)) { dev_err(chan->device->dev, "%s: bad direction?\n", __func__); return NULL; } if (!buf_len) { dev_err(chan->device->dev, "%s: bad buffer length (= 0)\n", __func__); return NULL; } /* * warn if buf_len is not a multiple of period_len - this may leed * to unexpected latencies for interrupts and thus audiable clicks */ if (buf_len % period_len) dev_warn_once(chan->device->dev, "%s: buffer_length (%zd) is not a multiple of period_len (%zd)\n", __func__, buf_len, period_len); /* Setup DREQ channel */ if (c->dreq != 0) info |= BCM2835_DMA_PER_MAP(c->dreq); if (direction == DMA_DEV_TO_MEM) { if (c->cfg.src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) return NULL; src = c->cfg.src_addr; dst = buf_addr; info |= BCM2835_DMA_S_DREQ | BCM2835_DMA_D_INC; } else { if (c->cfg.dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) return NULL; dst = c->cfg.dst_addr; src = buf_addr; info |= BCM2835_DMA_D_DREQ | BCM2835_DMA_S_INC; } /* calculate number of frames */ frames = /* number of periods */ DIV_ROUND_UP(buf_len, period_len) * /* number of frames per period */ bcm2835_dma_frames_for_length(period_len, max_len); /* * allocate the CB chain * note that we need to use GFP_NOWAIT, as the ALSA i2s dmaengine * implementation calls prep_dma_cyclic with interrupts disabled. */ d = bcm2835_dma_create_cb_chain(chan, direction, true, info, extra, frames, src, dst, buf_len, period_len, GFP_NOWAIT); if (!d) return NULL; /* wrap around into a loop */ d->cb_list[d->frames - 1].cb->next = d->cb_list[0].paddr; return vchan_tx_prep(&c->vc, &d->vd, flags); } static int bcm2835_dma_slave_config(struct dma_chan *chan, struct dma_slave_config *cfg) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); c->cfg = *cfg; return 0; } static int bcm2835_dma_terminate_all(struct dma_chan *chan) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); unsigned long flags; LIST_HEAD(head); spin_lock_irqsave(&c->vc.lock, flags); /* stop DMA activity */ if (c->desc) { vchan_terminate_vdesc(&c->desc->vd); c->desc = NULL; bcm2835_dma_abort(c); } vchan_get_all_descriptors(&c->vc, &head); spin_unlock_irqrestore(&c->vc.lock, flags); vchan_dma_desc_free_list(&c->vc, &head); return 0; } static void bcm2835_dma_synchronize(struct dma_chan *chan) { struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); vchan_synchronize(&c->vc); } static int bcm2835_dma_chan_init(struct bcm2835_dmadev *d, int chan_id, int irq, unsigned int irq_flags) { struct bcm2835_chan *c; c = devm_kzalloc(d->ddev.dev, sizeof(*c), GFP_KERNEL); if (!c) return -ENOMEM; c->vc.desc_free = bcm2835_dma_desc_free; vchan_init(&c->vc, &d->ddev); c->chan_base = BCM2835_DMA_CHANIO(d->base, chan_id); c->ch = chan_id; c->irq_number = irq; c->irq_flags = irq_flags; /* check in DEBUG register if this is a LITE channel */ if (readl(c->chan_base + BCM2835_DMA_DEBUG) & BCM2835_DMA_DEBUG_LITE) c->is_lite_channel = true; return 0; } static void bcm2835_dma_free(struct bcm2835_dmadev *od) { struct bcm2835_chan *c, *next; list_for_each_entry_safe(c, next, &od->ddev.channels, vc.chan.device_node) { list_del(&c->vc.chan.device_node); tasklet_kill(&c->vc.task); } } static const struct of_device_id bcm2835_dma_of_match[] = { { .compatible = "brcm,bcm2835-dma", }, {}, }; MODULE_DEVICE_TABLE(of, bcm2835_dma_of_match); static struct dma_chan *bcm2835_dma_xlate(struct of_phandle_args *spec, struct of_dma *ofdma) { struct bcm2835_dmadev *d = ofdma->of_dma_data; struct dma_chan *chan; chan = dma_get_any_slave_channel(&d->ddev); if (!chan) return NULL; /* Set DREQ from param */ to_bcm2835_dma_chan(chan)->dreq = spec->args[0]; return chan; } static int bcm2835_dma_probe(struct platform_device *pdev) { struct bcm2835_dmadev *od; struct resource *res; void __iomem *base; int rc; int i, j; int irq[BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED + 1]; int irq_flags; uint32_t chans_available; char chan_name[BCM2835_DMA_CHAN_NAME_SIZE]; if (!pdev->dev.dma_mask) pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); if (rc) return rc; od = devm_kzalloc(&pdev->dev, sizeof(*od), GFP_KERNEL); if (!od) return -ENOMEM; pdev->dev.dma_parms = &od->dma_parms; dma_set_max_seg_size(&pdev->dev, 0x3FFFFFFF); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); base = devm_ioremap_resource(&pdev->dev, res); if (IS_ERR(base)) return PTR_ERR(base); od->base = base; dma_cap_set(DMA_SLAVE, od->ddev.cap_mask); dma_cap_set(DMA_PRIVATE, od->ddev.cap_mask); dma_cap_set(DMA_CYCLIC, od->ddev.cap_mask); dma_cap_set(DMA_MEMCPY, od->ddev.cap_mask); od->ddev.device_alloc_chan_resources = bcm2835_dma_alloc_chan_resources; od->ddev.device_free_chan_resources = bcm2835_dma_free_chan_resources; od->ddev.device_tx_status = bcm2835_dma_tx_status; od->ddev.device_issue_pending = bcm2835_dma_issue_pending; od->ddev.device_prep_dma_cyclic = bcm2835_dma_prep_dma_cyclic; od->ddev.device_prep_slave_sg = bcm2835_dma_prep_slave_sg; od->ddev.device_prep_dma_memcpy = bcm2835_dma_prep_dma_memcpy; od->ddev.device_config = bcm2835_dma_slave_config; od->ddev.device_terminate_all = bcm2835_dma_terminate_all; od->ddev.device_synchronize = bcm2835_dma_synchronize; od->ddev.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES); od->ddev.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES); od->ddev.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV) | BIT(DMA_MEM_TO_MEM); od->ddev.residue_granularity = DMA_RESIDUE_GRANULARITY_BURST; od->ddev.dev = &pdev->dev; INIT_LIST_HEAD(&od->ddev.channels); platform_set_drvdata(pdev, od); /* Request DMA channel mask from device tree */ if (of_property_read_u32(pdev->dev.of_node, "brcm,dma-channel-mask", &chans_available)) { dev_err(&pdev->dev, "Failed to get channel mask\n"); rc = -EINVAL; goto err_no_dma; } /* get irqs for each channel that we support */ for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) { /* skip masked out channels */ if (!(chans_available & (1 << i))) { irq[i] = -1; continue; } /* get the named irq */ snprintf(chan_name, sizeof(chan_name), "dma%i", i); irq[i] = platform_get_irq_byname(pdev, chan_name); if (irq[i] >= 0) continue; /* legacy device tree case handling */ dev_warn_once(&pdev->dev, "missing interrupt-names property in device tree - legacy interpretation is used\n"); /* * in case of channel >= 11 * use the 11th interrupt and that is shared */ irq[i] = platform_get_irq(pdev, i < 11 ? i : 11); } /* get irqs for each channel */ for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) { /* skip channels without irq */ if (irq[i] < 0) continue; /* check if there are other channels that also use this irq */ irq_flags = 0; for (j = 0; j <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; j++) if ((i != j) && (irq[j] == irq[i])) { irq_flags = IRQF_SHARED; break; } /* initialize the channel */ rc = bcm2835_dma_chan_init(od, i, irq[i], irq_flags); if (rc) goto err_no_dma; } dev_dbg(&pdev->dev, "Initialized %i DMA channels\n", i); /* Device-tree DMA controller registration */ rc = of_dma_controller_register(pdev->dev.of_node, bcm2835_dma_xlate, od); if (rc) { dev_err(&pdev->dev, "Failed to register DMA controller\n"); goto err_no_dma; } rc = dma_async_device_register(&od->ddev); if (rc) { dev_err(&pdev->dev, "Failed to register slave DMA engine device: %d\n", rc); goto err_no_dma; } dev_dbg(&pdev->dev, "Load BCM2835 DMA engine driver\n"); return 0; err_no_dma: bcm2835_dma_free(od); return rc; } static int bcm2835_dma_remove(struct platform_device *pdev) { struct bcm2835_dmadev *od = platform_get_drvdata(pdev); dma_async_device_unregister(&od->ddev); bcm2835_dma_free(od); return 0; } static struct platform_driver bcm2835_dma_driver = { .probe = bcm2835_dma_probe, .remove = bcm2835_dma_remove, .driver = { .name = "bcm2835-dma", .of_match_table = of_match_ptr(bcm2835_dma_of_match), }, }; module_platform_driver(bcm2835_dma_driver); MODULE_ALIAS("platform:bcm2835-dma"); MODULE_DESCRIPTION("BCM2835 DMA engine driver"); MODULE_AUTHOR("Florian Meier "); MODULE_LICENSE("GPL");