// SPDX-License-Identifier: GPL-2.0
/*
 * Device Tree Source for the HiHope RZ/G2[MN] main board common parts
 *
 * Copyright (C) 2019 Renesas Electronics Corp.
 */

#include <dt-bindings/gpio/gpio.h>

/ {
	aliases {
		serial0 = &scif2;
	};

	chosen {
		bootargs = "ignore_loglevel";
		stdout-path = "serial0:115200n8";
	};

	leds {
		compatible = "gpio-leds";

		led0 {
			gpios = <&gpio6 11 GPIO_ACTIVE_HIGH>;
			label = "LED0";
		};

		led1 {
			gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
			label = "LED1";
		};

		led2 {
			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
			label = "LED2";
		};

		led3 {
			gpios = <&gpio0  0 GPIO_ACTIVE_HIGH>;
			label = "LED3";
		};
	};

	reg_1p8v: regulator0 {
		compatible = "regulator-fixed";
		regulator-name = "fixed-1.8V";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		regulator-boot-on;
		regulator-always-on;
	};

	reg_3p3v: regulator1 {
		compatible = "regulator-fixed";
		regulator-name = "fixed-3.3V";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
	};

	vbus0_usb2: regulator-vbus0-usb2 {
		compatible = "regulator-fixed";

		regulator-name = "USB20_VBUS0";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;

		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
		enable-active-high;
	};

	vccq_sdhi0: regulator-vccq-sdhi0 {
		compatible = "regulator-gpio";

		regulator-name = "SDHI0 VccQ";
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <3300000>;

		gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
		gpios-states = <1>;
		states = <3300000 1
			  1800000 0>;
	};
};

&ehci0 {
	status = "okay";
};

&ehci1 {
	status = "okay";
};

&extal_clk {
	clock-frequency = <16666666>;
};

&extalr_clk {
	clock-frequency = <32768>;
};

&gpio6 {
	usb1-reset {
		gpio-hog;
		gpios = <10 GPIO_ACTIVE_LOW>;
		output-low;
		line-name = "usb1-reset";
	};
};

&hsusb {
	dr_mode = "otg";
	status = "okay";
};

&ohci0 {
	status = "okay";
};

&ohci1 {
	status = "okay";
};

&pcie_bus_clk {
	clock-frequency = <100000000>;
};

&pfc {
	pinctrl-0 = <&scif_clk_pins>;
	pinctrl-names = "default";

	scif2_pins: scif2 {
		groups = "scif2_data_a";
		function = "scif2";
	};

	scif_clk_pins: scif_clk {
		groups = "scif_clk_a";
		function = "scif_clk";
	};

	sdhi0_pins: sd0 {
		groups = "sdhi0_data4", "sdhi0_ctrl";
		function = "sdhi0";
		power-source = <3300>;
	};

	sdhi0_pins_uhs: sd0_uhs {
		groups = "sdhi0_data4", "sdhi0_ctrl";
		function = "sdhi0";
		power-source = <1800>;
	};

	sdhi3_pins: sd3 {
		groups = "sdhi3_data8", "sdhi3_ctrl", "sdhi3_ds";
		function = "sdhi3";
		power-source = <1800>;
	};

	usb0_pins: usb0 {
		groups = "usb0";
		function = "usb0";
	};

	usb1_pins: usb1 {
		mux {
			groups = "usb1";
			function = "usb1";
		};

		ovc {
			pins = "GP_6_27";
			bias-pull-up;
		};
	};

	usb30_pins: usb30 {
		groups = "usb30";
		function = "usb30";
	};
};

&rwdt {
	timeout-sec = <60>;
	status = "okay";
};

&scif2 {
	pinctrl-0 = <&scif2_pins>;
	pinctrl-names = "default";

	status = "okay";
};

&scif_clk {
	clock-frequency = <14745600>;
};

&sdhi0 {
	pinctrl-0 = <&sdhi0_pins>;
	pinctrl-1 = <&sdhi0_pins_uhs>;
	pinctrl-names = "default", "state_uhs";

	vmmc-supply = <&reg_3p3v>;
	vqmmc-supply = <&vccq_sdhi0>;
	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
	bus-width = <4>;
	sd-uhs-sdr50;
	sd-uhs-sdr104;
	status = "okay";
};

&sdhi3 {
	pinctrl-0 = <&sdhi3_pins>;
	pinctrl-1 = <&sdhi3_pins>;
	pinctrl-names = "default", "state_uhs";

	vmmc-supply = <&reg_3p3v>;
	vqmmc-supply = <&reg_1p8v>;
	bus-width = <8>;
	mmc-hs200-1_8v;
	non-removable;
	fixed-emmc-driver-type = <1>;
};

&usb_extal_clk {
	clock-frequency = <50000000>;
};

&usb2_phy0 {
	pinctrl-0 = <&usb0_pins>;
	pinctrl-names = "default";

	vbus-supply = <&vbus0_usb2>;
	status = "okay";
};

&usb2_phy1 {
	pinctrl-0 = <&usb1_pins>;
	pinctrl-names = "default";

	status = "okay";
};

&usb3_peri0 {
	phys = <&usb3_phy0>;
	phy-names = "usb";

	companion = <&xhci0>;

	status = "okay";
};

&usb3_phy0 {
	status = "okay";
};

&usb3s0_clk {
	clock-frequency = <100000000>;
};

&xhci0 {
	pinctrl-0 = <&usb30_pins>;
	pinctrl-names = "default";

	status = "okay";
};