/* * linux/arch/arm/mach-omap2/clock.c * * Copyright (C) 2005-2008 Texas Instruments, Inc. * Copyright (C) 2004-2010 Nokia Corporation * * Contacts: * Richard Woodruff * Paul Walmsley * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ #undef DEBUG #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "soc.h" #include "clockdomain.h" #include "clock.h" #include "cm.h" #include "cm2xxx.h" #include "cm3xxx.h" #include "cm-regbits-24xx.h" #include "cm-regbits-34xx.h" #include "common.h" /* * MAX_MODULE_ENABLE_WAIT: maximum of number of microseconds to wait * for a module to indicate that it is no longer in idle */ #define MAX_MODULE_ENABLE_WAIT 100000 u16 cpu_mask; /* DPLL valid Fint frequency band limits - from 34xx TRM Section 4.7.6.2 */ #define OMAP3430_DPLL_FINT_BAND1_MIN 750000 #define OMAP3430_DPLL_FINT_BAND1_MAX 2100000 #define OMAP3430_DPLL_FINT_BAND2_MIN 7500000 #define OMAP3430_DPLL_FINT_BAND2_MAX 21000000 /* * DPLL valid Fint frequency range for OMAP36xx and OMAP4xxx. * From device data manual section 4.3 "DPLL and DLL Specifications". */ #define OMAP3PLUS_DPLL_FINT_MIN 32000 #define OMAP3PLUS_DPLL_FINT_MAX 52000000 /* * clkdm_control: if true, then when a clock is enabled in the * hardware, its clockdomain will first be enabled; and when a clock * is disabled in the hardware, its clockdomain will be disabled * afterwards. */ static bool clkdm_control = true; static LIST_HEAD(clk_hw_omap_clocks); struct clk_iomap { struct regmap *regmap; void __iomem *mem; }; static struct clk_iomap *clk_memmaps[CLK_MAX_MEMMAPS]; static void clk_memmap_writel(u32 val, void __iomem *reg) { struct clk_omap_reg *r = (struct clk_omap_reg *)® struct clk_iomap *io = clk_memmaps[r->index]; if (io->regmap) regmap_write(io->regmap, r->offset, val); else writel_relaxed(val, io->mem + r->offset); } static u32 clk_memmap_readl(void __iomem *reg) { u32 val; struct clk_omap_reg *r = (struct clk_omap_reg *)® struct clk_iomap *io = clk_memmaps[r->index]; if (io->regmap) regmap_read(io->regmap, r->offset, &val); else val = readl_relaxed(io->mem + r->offset); return val; } void omap2_clk_writel(u32 val, struct clk_hw_omap *clk, void __iomem *reg) { if (WARN_ON_ONCE(!(clk->flags & MEMMAP_ADDRESSING))) writel_relaxed(val, reg); else clk_memmap_writel(val, reg); } u32 omap2_clk_readl(struct clk_hw_omap *clk, void __iomem *reg) { if (WARN_ON_ONCE(!(clk->flags & MEMMAP_ADDRESSING))) return readl_relaxed(reg); else return clk_memmap_readl(reg); } static struct ti_clk_ll_ops omap_clk_ll_ops = { .clk_readl = clk_memmap_readl, .clk_writel = clk_memmap_writel, }; /** * omap2_clk_provider_init - initialize a clock provider * @match_table: DT device table to match for devices to init * @np: device node pointer for the this clock provider * @index: index for the clock provider + @syscon: syscon regmap pointer * @mem: iomem pointer for the clock provider memory area, only used if * syscon is not provided * * Initializes a clock provider module (CM/PRM etc.), registering * the memory mapping at specified index and initializing the * low level driver infrastructure. Returns 0 in success. */ int __init omap2_clk_provider_init(struct device_node *np, int index, struct regmap *syscon, void __iomem *mem) { struct clk_iomap *io; ti_clk_ll_ops = &omap_clk_ll_ops; io = kzalloc(sizeof(*io), GFP_KERNEL); io->regmap = syscon; io->mem = mem; clk_memmaps[index] = io; ti_dt_clk_init_provider(np, index); return 0; } /** * omap2_clk_legacy_provider_init - initialize a legacy clock provider * @index: index for the clock provider * @mem: iomem pointer for the clock provider memory area * * Initializes a legacy clock provider memory mapping. */ void __init omap2_clk_legacy_provider_init(int index, void __iomem *mem) { struct clk_iomap *io; ti_clk_ll_ops = &omap_clk_ll_ops; io = memblock_virt_alloc(sizeof(*io), 0); io->mem = mem; clk_memmaps[index] = io; } /* * OMAP2+ specific clock functions */ /* Private functions */ /** * _wait_idlest_generic - wait for a module to leave the idle state * @clk: module clock to wait for (needed for register offsets) * @reg: virtual address of module IDLEST register * @mask: value to mask against to determine if the module is active * @idlest: idle state indicator (0 or 1) for the clock * @name: name of the clock (for printk) * * Wait for a module to leave idle, where its idle-status register is * not inside the CM module. Returns 1 if the module left idle * promptly, or 0 if the module did not leave idle before the timeout * elapsed. XXX Deprecated - should be moved into drivers for the * individual IP block that the IDLEST register exists in. */ static int _wait_idlest_generic(struct clk_hw_omap *clk, void __iomem *reg, u32 mask, u8 idlest, const char *name) { int i = 0, ena = 0; ena = (idlest) ? 0 : mask; omap_test_timeout(((omap2_clk_readl(clk, reg) & mask) == ena), MAX_MODULE_ENABLE_WAIT, i); if (i < MAX_MODULE_ENABLE_WAIT) pr_debug("omap clock: module associated with clock %s ready after %d loops\n", name, i); else pr_err("omap clock: module associated with clock %s didn't enable in %d tries\n", name, MAX_MODULE_ENABLE_WAIT); return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0; }; /** * _omap2_module_wait_ready - wait for an OMAP module to leave IDLE * @clk: struct clk * belonging to the module * * If the necessary clocks for the OMAP hardware IP block that * corresponds to clock @clk are enabled, then wait for the module to * indicate readiness (i.e., to leave IDLE). This code does not * belong in the clock code and will be moved in the medium term to * module-dependent code. No return value. */ static void _omap2_module_wait_ready(struct clk_hw_omap *clk) { void __iomem *companion_reg, *idlest_reg; u8 other_bit, idlest_bit, idlest_val, idlest_reg_id; s16 prcm_mod; int r; /* Not all modules have multiple clocks that their IDLEST depends on */ if (clk->ops->find_companion) { clk->ops->find_companion(clk, &companion_reg, &other_bit); if (!(omap2_clk_readl(clk, companion_reg) & (1 << other_bit))) return; } clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit, &idlest_val); r = cm_split_idlest_reg(idlest_reg, &prcm_mod, &idlest_reg_id); if (r) { /* IDLEST register not in the CM module */ _wait_idlest_generic(clk, idlest_reg, (1 << idlest_bit), idlest_val, __clk_get_name(clk->hw.clk)); } else { omap_cm_wait_module_ready(0, prcm_mod, idlest_reg_id, idlest_bit); }; } /* Public functions */ /** * omap2_init_clk_clkdm - look up a clockdomain name, store pointer in clk * @clk: OMAP clock struct ptr to use * * Convert a clockdomain name stored in a struct clk 'clk' into a * clockdomain pointer, and save it into the struct clk. Intended to be * called during clk_register(). No return value. */ void omap2_init_clk_clkdm(struct clk_hw *hw) { struct clk_hw_omap *clk = to_clk_hw_omap(hw); struct clockdomain *clkdm; const char *clk_name; if (!clk->clkdm_name) return; clk_name = __clk_get_name(hw->clk); clkdm = clkdm_lookup(clk->clkdm_name); if (clkdm) { pr_debug("clock: associated clk %s to clkdm %s\n", clk_name, clk->clkdm_name); clk->clkdm = clkdm; } else { pr_debug("clock: could not associate clk %s to clkdm %s\n", clk_name, clk->clkdm_name); } } /** * omap2_clk_disable_clkdm_control - disable clkdm control on clk enable/disable * * Prevent the OMAP clock code from calling into the clockdomain code * when a hardware clock in that clockdomain is enabled or disabled. * Intended to be called at init time from omap*_clk_init(). No * return value. */ void __init omap2_clk_disable_clkdm_control(void) { clkdm_control = false; } /** * omap2_clk_dflt_find_companion - find companion clock to @clk * @clk: struct clk * to find the companion clock of * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in * @other_bit: u8 ** to return the companion clock bit shift in * * Note: We don't need special code here for INVERT_ENABLE for the * time being since INVERT_ENABLE only applies to clocks enabled by * CM_CLKEN_PLL * * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's * just a matter of XORing the bits. * * Some clocks don't have companion clocks. For example, modules with * only an interface clock (such as MAILBOXES) don't have a companion * clock. Right now, this code relies on the hardware exporting a bit * in the correct companion register that indicates that the * nonexistent 'companion clock' is active. Future patches will * associate this type of code with per-module data structures to * avoid this issue, and remove the casts. No return value. */ void omap2_clk_dflt_find_companion(struct clk_hw_omap *clk, void __iomem **other_reg, u8 *other_bit) { u32 r; /* * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes * it's just a matter of XORing the bits. */ r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN)); *other_reg = (__force void __iomem *)r; *other_bit = clk->enable_bit; } /** * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk * @clk: struct clk * to find IDLEST info for * @idlest_reg: void __iomem ** to return the CM_IDLEST va in * @idlest_bit: u8 * to return the CM_IDLEST bit shift in * @idlest_val: u8 * to return the idle status indicator * * Return the CM_IDLEST register address and bit shift corresponding * to the module that "owns" this clock. This default code assumes * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that * the IDLEST register address ID corresponds to the CM_*CLKEN * register address ID (e.g., that CM_FCLKEN2 corresponds to * CM_IDLEST2). This is not true for all modules. No return value. */ void omap2_clk_dflt_find_idlest(struct clk_hw_omap *clk, void __iomem **idlest_reg, u8 *idlest_bit, u8 *idlest_val) { u32 r; r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); *idlest_reg = (__force void __iomem *)r; *idlest_bit = clk->enable_bit; /* * 24xx uses 0 to indicate not ready, and 1 to indicate ready. * 34xx reverses this, just to keep us on our toes * AM35xx uses both, depending on the module. */ *idlest_val = ti_clk_get_features()->cm_idlest_val; } /** * omap2_dflt_clk_enable - enable a clock in the hardware * @hw: struct clk_hw * of the clock to enable * * Enable the clock @hw in the hardware. We first call into the OMAP * clockdomain code to "enable" the corresponding clockdomain if this * is the first enabled user of the clockdomain. Then program the * hardware to enable the clock. Then wait for the IP block that uses * this clock to leave idle (if applicable). Returns the error value * from clkdm_clk_enable() if it terminated with an error, or -EINVAL * if @hw has a null clock enable_reg, or zero upon success. */ int omap2_dflt_clk_enable(struct clk_hw *hw) { struct clk_hw_omap *clk; u32 v; int ret = 0; clk = to_clk_hw_omap(hw); if (clkdm_control && clk->clkdm) { ret = clkdm_clk_enable(clk->clkdm, hw->clk); if (ret) { WARN(1, "%s: could not enable %s's clockdomain %s: %d\n", __func__, __clk_get_name(hw->clk), clk->clkdm->name, ret); return ret; } } if (unlikely(clk->enable_reg == NULL)) { pr_err("%s: %s missing enable_reg\n", __func__, __clk_get_name(hw->clk)); ret = -EINVAL; goto err; } /* FIXME should not have INVERT_ENABLE bit here */ v = omap2_clk_readl(clk, clk->enable_reg); if (clk->flags & INVERT_ENABLE) v &= ~(1 << clk->enable_bit); else v |= (1 << clk->enable_bit); omap2_clk_writel(v, clk, clk->enable_reg); v = omap2_clk_readl(clk, clk->enable_reg); /* OCP barrier */ if (clk->ops && clk->ops->find_idlest) _omap2_module_wait_ready(clk); return 0; err: if (clkdm_control && clk->clkdm) clkdm_clk_disable(clk->clkdm, hw->clk); return ret; } /** * omap2_dflt_clk_disable - disable a clock in the hardware * @hw: struct clk_hw * of the clock to disable * * Disable the clock @hw in the hardware, and call into the OMAP * clockdomain code to "disable" the corresponding clockdomain if all * clocks/hwmods in that clockdomain are now disabled. No return * value. */ void omap2_dflt_clk_disable(struct clk_hw *hw) { struct clk_hw_omap *clk; u32 v; clk = to_clk_hw_omap(hw); if (!clk->enable_reg) { /* * 'independent' here refers to a clock which is not * controlled by its parent. */ pr_err("%s: independent clock %s has no enable_reg\n", __func__, __clk_get_name(hw->clk)); return; } v = omap2_clk_readl(clk, clk->enable_reg); if (clk->flags & INVERT_ENABLE) v |= (1 << clk->enable_bit); else v &= ~(1 << clk->enable_bit); omap2_clk_writel(v, clk, clk->enable_reg); /* No OCP barrier needed here since it is a disable operation */ if (clkdm_control && clk->clkdm) clkdm_clk_disable(clk->clkdm, hw->clk); } /** * omap2_clkops_enable_clkdm - increment usecount on clkdm of @hw * @hw: struct clk_hw * of the clock being enabled * * Increment the usecount of the clockdomain of the clock pointed to * by @hw; if the usecount is 1, the clockdomain will be "enabled." * Only needed for clocks that don't use omap2_dflt_clk_enable() as * their enable function pointer. Passes along the return value of * clkdm_clk_enable(), -EINVAL if @hw is not associated with a * clockdomain, or 0 if clock framework-based clockdomain control is * not implemented. */ int omap2_clkops_enable_clkdm(struct clk_hw *hw) { struct clk_hw_omap *clk; int ret = 0; clk = to_clk_hw_omap(hw); if (unlikely(!clk->clkdm)) { pr_err("%s: %s: no clkdm set ?!\n", __func__, __clk_get_name(hw->clk)); return -EINVAL; } if (unlikely(clk->enable_reg)) pr_err("%s: %s: should use dflt_clk_enable ?!\n", __func__, __clk_get_name(hw->clk)); if (!clkdm_control) { pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", __func__, __clk_get_name(hw->clk)); return 0; } ret = clkdm_clk_enable(clk->clkdm, hw->clk); WARN(ret, "%s: could not enable %s's clockdomain %s: %d\n", __func__, __clk_get_name(hw->clk), clk->clkdm->name, ret); return ret; } /** * omap2_clkops_disable_clkdm - decrement usecount on clkdm of @hw * @hw: struct clk_hw * of the clock being disabled * * Decrement the usecount of the clockdomain of the clock pointed to * by @hw; if the usecount is 0, the clockdomain will be "disabled." * Only needed for clocks that don't use omap2_dflt_clk_disable() as their * disable function pointer. No return value. */ void omap2_clkops_disable_clkdm(struct clk_hw *hw) { struct clk_hw_omap *clk; clk = to_clk_hw_omap(hw); if (unlikely(!clk->clkdm)) { pr_err("%s: %s: no clkdm set ?!\n", __func__, __clk_get_name(hw->clk)); return; } if (unlikely(clk->enable_reg)) pr_err("%s: %s: should use dflt_clk_disable ?!\n", __func__, __clk_get_name(hw->clk)); if (!clkdm_control) { pr_err("%s: %s: clkfw-based clockdomain control disabled ?!\n", __func__, __clk_get_name(hw->clk)); return; } clkdm_clk_disable(clk->clkdm, hw->clk); } /** * omap2_dflt_clk_is_enabled - is clock enabled in the hardware? * @hw: struct clk_hw * to check * * Return 1 if the clock represented by @hw is enabled in the * hardware, or 0 otherwise. Intended for use in the struct * clk_ops.is_enabled function pointer. */ int omap2_dflt_clk_is_enabled(struct clk_hw *hw) { struct clk_hw_omap *clk = to_clk_hw_omap(hw); u32 v; v = omap2_clk_readl(clk, clk->enable_reg); if (clk->flags & INVERT_ENABLE) v ^= BIT(clk->enable_bit); v &= BIT(clk->enable_bit); return v ? 1 : 0; } static int __initdata mpurate; /* * By default we use the rate set by the bootloader. * You can override this with mpurate= cmdline option. */ static int __init omap_clk_setup(char *str) { get_option(&str, &mpurate); if (!mpurate) return 1; if (mpurate < 1000) mpurate *= 1000000; return 1; } __setup("mpurate=", omap_clk_setup); /** * omap2_init_clk_hw_omap_clocks - initialize an OMAP clock * @clk: struct clk * to initialize * * Add an OMAP clock @clk to the internal list of OMAP clocks. Used * temporarily for autoidle handling, until this support can be * integrated into the common clock framework code in some way. No * return value. */ void omap2_init_clk_hw_omap_clocks(struct clk *clk) { struct clk_hw_omap *c; if (__clk_get_flags(clk) & CLK_IS_BASIC) return; c = to_clk_hw_omap(__clk_get_hw(clk)); list_add(&c->node, &clk_hw_omap_clocks); } /** * omap2_clk_enable_autoidle_all - enable autoidle on all OMAP clocks that * support it * * Enable clock autoidle on all OMAP clocks that have allow_idle * function pointers associated with them. This function is intended * to be temporary until support for this is added to the common clock * code. Returns 0. */ int omap2_clk_enable_autoidle_all(void) { struct clk_hw_omap *c; list_for_each_entry(c, &clk_hw_omap_clocks, node) if (c->ops && c->ops->allow_idle) c->ops->allow_idle(c); of_ti_clk_allow_autoidle_all(); return 0; } /** * omap2_clk_disable_autoidle_all - disable autoidle on all OMAP clocks that * support it * * Disable clock autoidle on all OMAP clocks that have allow_idle * function pointers associated with them. This function is intended * to be temporary until support for this is added to the common clock * code. Returns 0. */ int omap2_clk_disable_autoidle_all(void) { struct clk_hw_omap *c; list_for_each_entry(c, &clk_hw_omap_clocks, node) if (c->ops && c->ops->deny_idle) c->ops->deny_idle(c); of_ti_clk_deny_autoidle_all(); return 0; } /** * omap2_clk_deny_idle - disable autoidle on an OMAP clock * @clk: struct clk * to disable autoidle for * * Disable autoidle on an OMAP clock. */ int omap2_clk_deny_idle(struct clk *clk) { struct clk_hw_omap *c; if (__clk_get_flags(clk) & CLK_IS_BASIC) return -EINVAL; c = to_clk_hw_omap(__clk_get_hw(clk)); if (c->ops && c->ops->deny_idle) c->ops->deny_idle(c); return 0; } /** * omap2_clk_allow_idle - enable autoidle on an OMAP clock * @clk: struct clk * to enable autoidle for * * Enable autoidle on an OMAP clock. */ int omap2_clk_allow_idle(struct clk *clk) { struct clk_hw_omap *c; if (__clk_get_flags(clk) & CLK_IS_BASIC) return -EINVAL; c = to_clk_hw_omap(__clk_get_hw(clk)); if (c->ops && c->ops->allow_idle) c->ops->allow_idle(c); return 0; } /** * omap2_clk_enable_init_clocks - prepare & enable a list of clocks * @clk_names: ptr to an array of strings of clock names to enable * @num_clocks: number of clock names in @clk_names * * Prepare and enable a list of clocks, named by @clk_names. No * return value. XXX Deprecated; only needed until these clocks are * properly claimed and enabled by the drivers or core code that uses * them. XXX What code disables & calls clk_put on these clocks? */ void omap2_clk_enable_init_clocks(const char **clk_names, u8 num_clocks) { struct clk *init_clk; int i; for (i = 0; i < num_clocks; i++) { init_clk = clk_get(NULL, clk_names[i]); if (WARN(IS_ERR(init_clk), "could not find init clock %s\n", clk_names[i])) continue; clk_prepare_enable(init_clk); } } const struct clk_hw_omap_ops clkhwops_wait = { .find_idlest = omap2_clk_dflt_find_idlest, .find_companion = omap2_clk_dflt_find_companion, }; /** * omap2_clk_switch_mpurate_at_boot - switch ARM MPU rate by boot-time argument * @mpurate_ck_name: clk name of the clock to change rate * * Change the ARM MPU clock rate to the rate specified on the command * line, if one was specified. @mpurate_ck_name should be * "virt_prcm_set" on OMAP2xxx and "dpll1_ck" on OMAP34xx/OMAP36xx. * XXX Does not handle voltage scaling - on OMAP2xxx this is currently * handled by the virt_prcm_set clock, but this should be handled by * the OPP layer. XXX This is intended to be handled by the OPP layer * code in the near future and should be removed from the clock code. * Returns -EINVAL if 'mpurate' is zero or if clk_set_rate() rejects * the rate, -ENOENT if the struct clk referred to by @mpurate_ck_name * cannot be found, or 0 upon success. */ int __init omap2_clk_switch_mpurate_at_boot(const char *mpurate_ck_name) { struct clk *mpurate_ck; int r; if (!mpurate) return -EINVAL; mpurate_ck = clk_get(NULL, mpurate_ck_name); if (WARN(IS_ERR(mpurate_ck), "Failed to get %s.\n", mpurate_ck_name)) return -ENOENT; r = clk_set_rate(mpurate_ck, mpurate); if (r < 0) { WARN(1, "clock: %s: unable to set MPU rate to %d: %d\n", mpurate_ck_name, mpurate, r); clk_put(mpurate_ck); return -EINVAL; } calibrate_delay(); clk_put(mpurate_ck); return 0; } /** * omap2_clk_print_new_rates - print summary of current clock tree rates * @hfclkin_ck_name: clk name for the off-chip HF oscillator * @core_ck_name: clk name for the on-chip CORE_CLK * @mpu_ck_name: clk name for the ARM MPU clock * * Prints a short message to the console with the HFCLKIN oscillator * rate, the rate of the CORE clock, and the rate of the ARM MPU clock. * Called by the boot-time MPU rate switching code. XXX This is intended * to be handled by the OPP layer code in the near future and should be * removed from the clock code. No return value. */ void __init omap2_clk_print_new_rates(const char *hfclkin_ck_name, const char *core_ck_name, const char *mpu_ck_name) { struct clk *hfclkin_ck, *core_ck, *mpu_ck; unsigned long hfclkin_rate; mpu_ck = clk_get(NULL, mpu_ck_name); if (WARN(IS_ERR(mpu_ck), "clock: failed to get %s.\n", mpu_ck_name)) return; core_ck = clk_get(NULL, core_ck_name); if (WARN(IS_ERR(core_ck), "clock: failed to get %s.\n", core_ck_name)) return; hfclkin_ck = clk_get(NULL, hfclkin_ck_name); if (WARN(IS_ERR(hfclkin_ck), "Failed to get %s.\n", hfclkin_ck_name)) return; hfclkin_rate = clk_get_rate(hfclkin_ck); pr_info("Switched to new clocking rate (Crystal/Core/MPU): %ld.%01ld/%ld/%ld MHz\n", (hfclkin_rate / 1000000), ((hfclkin_rate / 100000) % 10), (clk_get_rate(core_ck) / 1000000), (clk_get_rate(mpu_ck) / 1000000)); } /** * ti_clk_init_features - init clock features struct for the SoC * * Initializes the clock features struct based on the SoC type. */ void __init ti_clk_init_features(void) { struct ti_clk_features features = { 0 }; /* Fint setup for DPLLs */ if (cpu_is_omap3430()) { features.fint_min = OMAP3430_DPLL_FINT_BAND1_MIN; features.fint_max = OMAP3430_DPLL_FINT_BAND2_MAX; features.fint_band1_max = OMAP3430_DPLL_FINT_BAND1_MAX; features.fint_band2_min = OMAP3430_DPLL_FINT_BAND2_MIN; } else { features.fint_min = OMAP3PLUS_DPLL_FINT_MIN; features.fint_max = OMAP3PLUS_DPLL_FINT_MAX; } /* Bypass value setup for DPLLs */ if (cpu_is_omap24xx()) { features.dpll_bypass_vals |= (1 << OMAP2XXX_EN_DPLL_LPBYPASS) | (1 << OMAP2XXX_EN_DPLL_FRBYPASS); } else if (cpu_is_omap34xx()) { features.dpll_bypass_vals |= (1 << OMAP3XXX_EN_DPLL_LPBYPASS) | (1 << OMAP3XXX_EN_DPLL_FRBYPASS); } else if (soc_is_am33xx() || cpu_is_omap44xx() || soc_is_am43xx() || soc_is_omap54xx() || soc_is_dra7xx()) { features.dpll_bypass_vals |= (1 << OMAP4XXX_EN_DPLL_LPBYPASS) | (1 << OMAP4XXX_EN_DPLL_FRBYPASS) | (1 << OMAP4XXX_EN_DPLL_MNBYPASS); } /* Jitter correction only available on OMAP343X */ if (cpu_is_omap343x()) features.flags |= TI_CLK_DPLL_HAS_FREQSEL; /* Idlest value for interface clocks. * 24xx uses 0 to indicate not ready, and 1 to indicate ready. * 34xx reverses this, just to keep us on our toes * AM35xx uses both, depending on the module. */ if (cpu_is_omap24xx()) features.cm_idlest_val = OMAP24XX_CM_IDLEST_VAL; else if (cpu_is_omap34xx()) features.cm_idlest_val = OMAP34XX_CM_IDLEST_VAL; /* On OMAP3430 ES1.0, DPLL4 can't be re-programmed */ if (omap_rev() == OMAP3430_REV_ES1_0) features.flags |= TI_CLK_DPLL4_DENY_REPROGRAM; ti_clk_setup_features(&features); }