Kconfig - OpenGrok cross reference for /openbmc/u-boot/drivers/serial/Kconfig

11 	  Select a default baudrate, where "default" has a driver-specific
19 	# non-dm serial code
34 	  in U-Boot.
41 	  In very space-constrained devices even the full UART driver is too
43 	  This option enables the full UART in U-Boot, so if is it disabled,
51 	  In very space-constrained devices even the full UART driver is too
61 	  In very space-constrained devices even the full UART driver is too
159 	  The debug UART is intended for use very early in U-Boot to debug
163 	  - Make sure your UART supports this interface
164 	  - Enable CONFIG_DEBUG_UART
165 	  - Enable the CONFIG for your UART to tell it to provide this interface
167 	  - Define the required settings as needed (see below)
168 	  - Call debug_uart_init() before use
169 	  - Call debug_uart_putc() to output a character
224 	  be available until the real driver-model serial is running.
247 	  U-Boot when running on top of EFI (Extensive Firmware Interface).
255 	  be available until the real driver-model serial is running.
263 	  be available until the real driver-model serial is running.
270 	  be available until the real driver-model serial is running.
288 	  be available until the real driver-model serial is running.
295 	  be available until the real driver-model serial is running.
351 	  be available until the real driver-model serial is running.
363 	bool "UniPhier on-chip UART"
366 	  Select this to enable a debug UART using the UniPhier on-chip UART.
368 	  driver will be available until the real driver-model serial is
379 	bool "MediaTek High-speed UART"
382 	  Select this to enable a debug UART using the MediaTek High-speed
395 	  This is the base address of your UART for memory-mapped UARTs.
420 	  registers, 2=32-bit word registers, etc.
423 	bool "Enable board-specific debug UART init"
439 	  U-Boot has the UART ready for use (i.e. your code calls
448 	  initialized by the time U-Boot starts its execution.
459 	  Note that this does not work for every ns16550-compatible UART and
495 	  doc/device-tree-bindings/serial/qca,ar9330-uart.txt.
512 	bool "Support for BCM283x Mini-UART"
516 	  Select this to enable Mini-UART support on BCM283X family of SoCs.
541 	bool "Freescale LPUART support"
543 	  Select this to enable a Low Power UART for Freescale VF610 and
568 	bool "Support for Microchip PIC32 on-chip UART"
612 	bool "Rockchip on-chip UART support"
616 	  CONFIG_SPL_OF_PLATDATA (i.e. a compiled-in device tree replacemenmt).
617 	  This uses the ns16550 driver, converting the platdata from of-platdata
628 	  U-Boot.
630 	  The operation of the console is controlled by the -t command-line
631 	  flag. In raw mode, U-Boot sees all characters from the terminal
632 	  before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
633 	  is processed by the terminal, and terminates U-Boot. Valid options
636 	     -t raw-with-sigs	Raw mode, Ctrl-C will terminate U-Boot
637 	     -t raw		Raw mode, Ctrl-C is processed by U-Boot
638 	     -t cooked		Cooked mode, Ctrl-C terminates
649 	bool "Support for UniPhier on-chip UART"
653 	  If you have a UniPhier based board and want to use the on-chip
667 	  If you have an Amlogic Meson based board and want to use the on-chip
671 	bool "Qualcomm on-chip UART"
685 	  If you have an TI based SoC and want to use the on-chip serial
692 	  If you have a Actions Semi OWL based board and want to use the on-chip
709 	bool "STMicroelectronics on-chip UART"
717 	bool "STMicroelectronics STM32 SoCs on-chip UART"
732 	bool "MediaTek High-speed UART support"
735 	  Select this to enable UART support for MediaTek High-speed UART
738 	  The High-speed UART is compatible with the ns16550a UART and have
739 	  its own high-speed registers.