Lines Matching +full:axp209 +full:- +full:battery +full:- +full:power +full:- +full:supply
1 menu "Power" menu
3 source "drivers/power/domain/Kconfig"
5 source "drivers/power/pmic/Kconfig"
7 source "drivers/power/regulator/Kconfig"
19 ---help---
27 ---help---
32 bool "axp209 pmic support"
36 ---help---
37 Select this to enable support for the axp209 pmic found on most
45 ---help---
54 ---help---
62 ---help---
69 ---help---
80 ---help---
83 generic 3.3V IO voltage for external devices like the lcd-panal and
85 save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
86 dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
97 ---help---
100 On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
101 On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
102 On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
104 On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
105 On R40 boards dcdc2 is VDD-CPU and should be 1.1V
115 ---help---
118 On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
120 On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
121 On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
122 On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
123 On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
124 On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
133 ---help---
136 On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
137 On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
139 On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
140 On A83T boards dcdc4 is used for VDD-GPU.
146 ---help---
149 On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
158 ---help---
161 On A31 boards aldo1 is often used to power the wifi module.
162 On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
174 ---help---
180 On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
182 On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
190 ---help---
194 On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
197 On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
204 ---help---
213 ---help---
219 ---help---
226 ---help---
238 ---help---
241 and resulting an AXP209 shutdown.
247 ---help---
256 ---help---
259 to power the ethernet phy. On A23, A33 and A80 boards this is often
260 used to power the wifi.
267 ---help---
276 ---help---
284 ---help---
292 ---help---
300 ---help---
309 ---help---
311 disable eldo3. On some A31(s) tablets it might be used to supply
320 ---help---
323 On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
330 ---help---
333 On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
339 ---help---
347 ---help---
354 ---help---
356 is typically used to power the VDD-CPU and should be 1200mV.
361 bool "Enable driver for TI TWL4030 power management chip"
363 ---help---
364 The TWL4030 in a combination audio CODEC/power management with