u-boot/doc/README.u-boot_on_efi

5 U-Boot on EFI
7 This document provides information about U-Boot running on top of EFI, either
8 as an application or just as a means of getting U-Boot onto a new platform.
29 Running U-Boot on EFI is useful in several situations:
31 - You have EFI running on a board but U-Boot does not natively support it
32 fully yet. You can boot into U-Boot from EFI and use that until U-Boot is
38 - You plan to use coreboot to boot into U-Boot but coreboot support does
39 not currently exist for your platform. In the meantime you can use U-Boot
40 on EFI and then move to U-Boot on coreboot when ready
42 - You use EFI but want to experiment with a simpler alternative like U-Boot
51 U-Boot supports running as an EFI application for 32-bit EFI only. This is
55 More usefully, U-Boot supports building itself as a payload for either 32-bit
56 or 64-bit EFI. U-Boot is packaged up and loaded in its entirety by EFI. Once
57 started, U-Boot changes to 32-bit mode (currently) and takes over the
58 machine. You can use devices, boot a kernel, etc.
67 To build U-Boot as an EFI application (32-bit EFI required), enable CONFIG_EFI
69 for this. Just build U-Boot as normal, e.g.
74 To build U-Boot as an EFI payload (32-bit or 64-bit EFI can be used), enable
77 and efi-x86_payload32_defconfig) are set up for this. Then build U-Boot as
85    u-boot-app.efi      - U-Boot EFI application
86    u-boot-payload.efi  - U-Boot EFI payload application
96    cp /path/to/u-boot*.efi /tmp/efi
100 type 'fs0:u-boot-payload.efi' to run the payload or 'fs0:u-boot-app.efi' to
104 To try it on real hardware, put u-boot-app.efi on a suitable boot medium,
107    fs0:u-boot-payload.efi
109 (or fs0:u-boot-app.efi for the application)
111 This will start the payload, copy U-Boot into RAM and start U-Boot. Note
127 For the application the whole of U-Boot is built as a shared library. The
129 functions with efi_init(), sets up U-Boot global_data, allocates memory for
130 U-Boot's malloc(), etc. and enters the normal init sequence (board_init_f()
133 Since U-Boot limits its memory access to the allocated regions very little
139 'boot services' to send and receive characters. Although it is implemented
141 boot EFI with video output then the 'serial' device will operate on your
144 consoles will be active. Even though U-Boot does the same thing normally,
145 These are features of EFI, not U-Boot.
148 U-Boot is highly portable. Most of the difficulty is in modifying the
159 U-Boot exactly as normal for your target board, then adding the entire
165 function is called by EFI. It is responsible for copying U-Boot from its
166 original location into memory, disabling EFI boot services and starting
167 U-Boot. U-Boot then starts as normal, relocates, starts all drivers, etc.
173 used by U-Boot (the payload). In fact when U-Boot starts it has all of the
179 The payload can pass information to U-Boot in the form of EFI tables. At
182 display this list. U-Boot uses the list to work out where to relocate
185 Although U-Boot can use any memory it likes, EFI marks some memory as used
186 by 'run-time services', code that hangs around while U-Boot is running and
189 fan speed. U-Boot uses only 'conventional' memory, in EFI terminology. It
195 U-Boot drivers typically don't use interrupts. Since EFI enables interrupts
196 it is possible that an interrupt will fire that U-Boot cannot handle. This
197 seems to cause problems. For this reason the U-Boot payload runs with
208 Everything else is built as a normal U-Boot, so is always 32-bit on x86 at
225 - Avoid turning off boot services in the stub. Instead allow U-Boot to make
226 use of boot services in case it wants to. It is unclear what it might want