arm/dts/zynqmp-zcu100-revC.dts

1 // SPDX-License-Identifier: GPL-2.0+
5  * (C) Copyright 2016 - 2018, Xilinx, Inc.
11 /dts-v1/;
14 #include "zynqmp-clk.dtsi"
15 #include <dt-bindings/input/input.h>
16 #include <dt-bindings/interrupt-controller/irq.h>
17 #include <dt-bindings/gpio/gpio.h>
18 #include <dt-bindings/phy/phy.h>
22 	compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp";
32 		spi1 = &spi1;
41 		stdout-path = "serial0:115200n8";
49 	gpio-keys {
50 		compatible = "gpio-keys";
56 			gpio-key,wakeup;
61 	iio-hwmon {
62 		compatible = "iio-hwmon";
63 		io-channels = <&xilinx_ams 0>, <&xilinx_ams 1>, <&xilinx_ams 2>,
71 		compatible = "gpio-leds";
75 			linux,default-trigger = "heartbeat";
81 			linux,default-trigger = "phy0tx"; /* WLAN tx */
82 			default-state = "off";
88 			linux,default-trigger = "phy0rx"; /* WLAN rx */
89 			default-state = "off";
95 			linux,default-trigger = "bluetooth-power";
101 			default-state = "on";
108 		trigger-gpios = <&gpio 26 GPIO_ACTIVE_LOW>; /* INT line - input */
110 		watchdog-gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; /* MIO on PAD */
111 		kill-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; /* KILL signal - output */
114 	wmmcsdio_fixed: fixedregulator-mmcsdio {
115 		compatible = "regulator-fixed";
116 		regulator-name = "wmmcsdio_fixed";
117 		regulator-min-microvolt = <3300000>;
118 		regulator-max-microvolt = <3300000>;
119 		regulator-always-on;
120 		regulator-boot-on;
124 		compatible = "mmc-pwrseq-simple";
125 		reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */
135 	gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL",
142 			  "", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C",
143 			  "GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E",
144 			  "GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3",
170 	clock-frequency = <100000>;
171 	i2c-mux@75 { /* u11 */
173 		#address-cells = <1>;
174 		#size-cells = <0>;
177 			#address-cells = <1>;
178 			#size-cells = <0>;
180 			label = "LS-I2C0";
183 			#address-cells = <1>;
184 			#size-cells = <0>;
186 			label = "LS-I2C1";
189 			#address-cells = <1>;
190 			#size-cells = <0>;
192 			label = "HS-I2C2";
195 			#address-cells = <1>;
196 			#size-cells = <0>;
198 			label = "HS-I2C3";
201 			#address-cells = <1>;
202 			#size-cells = <0>;
208 				interrupt-parent = <&gpio>;
210 				#gpio-cells = <2>;
211 				gpio-controller;
215 			#address-cells = <1>;
216 			#size-cells = <0>;
222 				shunt-resistor = <10000>;
227 			#address-cells = <1>;
228 			#size-cells = <0>;
235 			#address-cells = <1>;
236 			#size-cells = <0>;
239 			 * usb5744 (DNP) - U5
240 			 * 100kHz - this is default freq for us
253 	no-1-8-v;
254 	disable-wp;
260 	bus-width = <0x4>;
262 	non-removable;
263 	disable-wp;
264 	cap-power-off-card;
265 	mmc-pwrseq = <&sdio_pwrseq>;
266 	vqmmc-supply = <&wmmcsdio_fixed>;
267 	#address-cells = <1>;
268 	#size-cells = <0>;
272 		interrupt-parent = <&gpio>;
283 	label = "LS-SPI0";
284 	num-cs = <1>;
287 &spi1 { /* High Speed connector */
289 	label = "HS-SPI1";
290 	num-cs = <1>;
296 		compatible = "ti,wl1831-st";
297 		enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
314 	phy-names = "usb3-phy";
316 	maximum-speed = "super-speed";
327 	phy-names = "usb3-phy";
329 	maximum-speed = "super-speed";