arm/dts/sun8i-a33-sinlinx-sina33.dts

2  * Copyright 2015 Chen-Yu Tsai
4  * Chen-Yu Tsai <wens@csie.org>
6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun8i-a33.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/input/input.h>
54 	compatible = "sinlinx,sina33", "allwinner,sun8i-a33";
61 		stdout-path = "serial0:115200n8";
65 		compatible = "netron-dy,e231732";
66 		#address-cells = <1>;
67 		#size-cells = <0>;
71 			#address-cells = <1>;
72 			#size-cells = <0>;
76 				remote-endpoint = <&tcon0_out_panel>;
87 	cpu-supply = <&reg_dcdc3>;
91 	opp-1104000000 {
92 		opp-hz = /bits/ 64 <1104000000>;
93 		opp-microvolt = <1320000>;
94 		clock-latency-ns = <244144>; /* 8 32k periods */
97 	opp-1200000000 {
98 		opp-hz = /bits/ 64 <1200000000>;
99 		opp-microvolt = <1320000>;
100 		clock-latency-ns = <244144>; /* 8 32k periods */
117 	vref-supply = <&reg_dcdc1>;
143 	pinctrl-names = "default";
144 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
145 	vmmc-supply = <&reg_dcdc1>;
146 	bus-width = <4>;
147 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
152 	pinctrl-names = "default";
153 	pinctrl-0 = <&mmc2_8bit_pins>;
154 	vmmc-supply = <&reg_dcdc1>;
155 	bus-width = <8>;
156 	non-removable;
157 	cap-mmc-hw-reset;
163 	drive-strength = <40>;
164 	/* eMMC is missing pull-ups */
165 	bias-pull-up;
176 		bias-pull-up;
183 	axp22x: pmic@3a3 {
184 		compatible = "x-powers,axp223";
186 		interrupt-parent = <&nmi_intc>;
188 		eldoin-supply = <&reg_dcdc1>;
203 	regulator-always-on;
204 	regulator-min-microvolt = <3000000>;
205 	regulator-max-microvolt = <3000000>;
206 	regulator-name = "vcc-io";
210 	regulator-always-on;
211 	regulator-min-microvolt = <2350000>;
212 	regulator-max-microvolt = <2650000>;
213 	regulator-name = "vdd-dll";
217 	regulator-always-on;
218 	regulator-min-microvolt = <2700000>;
219 	regulator-max-microvolt = <3300000>;
220 	regulator-name = "vcc-pll-avcc";
224 	regulator-always-on;
225 	regulator-min-microvolt = <900000>;
226 	regulator-max-microvolt = <1400000>;
227 	regulator-name = "vdd-cpus";
231 	regulator-always-on;
232 	regulator-min-microvolt = <3000000>;
233 	regulator-max-microvolt = <3000000>;
234 	regulator-name = "vcc-3v0";
238 	regulator-always-on;
239 	regulator-min-microvolt = <900000>;
240 	regulator-max-microvolt = <1400000>;
241 	regulator-name = "vdd-sys";
245 	regulator-always-on;
246 	regulator-min-microvolt = <900000>;
247 	regulator-max-microvolt = <1400000>;
248 	regulator-name = "vdd-cpu";
252 	regulator-always-on;
253 	regulator-min-microvolt = <1500000>;
254 	regulator-max-microvolt = <1500000>;
255 	regulator-name = "vcc-dram";
259 	regulator-name = "vcc-rtc";
267 	pinctrl-names = "default";
268 	pinctrl-0 = <&lcd_rgb666_pins>;
275 		remote-endpoint = <&panel_input>;
280 	pinctrl-names = "default";
281 	pinctrl-0 = <&uart0_pins_b>;
292 	usb1_vbus-supply = <&reg_vcc5v0>; /* USB1 VBUS is always on */