arm/dts/sun7i-a20-wits-pro-a20-dkt.dts

4  * This file is dual-licensed: you can use it either under the terms
43 /dts-v1/;
44 #include "sun7i-a20.dtsi"
45 #include "sunxi-common-regulators.dtsi"
47 #include <dt-bindings/gpio/gpio.h>
48 #include <dt-bindings/input/input.h>
49 #include <dt-bindings/interrupt-controller/irq.h>
53 	compatible = "wits,pro-a20-dkt", "allwinner,sun7i-a20";
60 		stdout-path = "serial0:115200n8";
64 		compatible = "mmc-pwrseq-simple";
65 		pinctrl-names = "default";
66 		pinctrl-0 = <&vmmc3_pin_ap6xxx_wl_regon>;
67 		reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
72 	cpu-supply = <&reg_dcdc2>;
84 	pinctrl-names = "default";
85 	pinctrl-0 = <&gmac_pins_rgmii_a>;
87 	phy-mode = "rgmii";
90 	phy1: ethernet-phy@1 {
96 	pinctrl-names = "default";
97 	pinctrl-0 = <&i2c0_pins_a>;
102 		interrupt-parent = <&nmi_intc>;
108 	pinctrl-names = "default";
109 	pinctrl-0 = <&i2c1_pins_a>;
114 	pinctrl-names = "default";
115 	pinctrl-0 = <&i2c2_pins_a>;
122 	pinctrl-names = "default";
123 	pinctrl-0 = <&mmc0_pins_a>;
124 	vmmc-supply = <&reg_vcc3v3>;
125 	bus-width = <4>;
126 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
131 	pinctrl-names = "default";
132 	pinctrl-0 = <&mmc3_pins_a>;
133 	vmmc-supply = <&reg_vcc3v3>;
134 	mmc-pwrseq = <&mmc3_pwrseq>;
135 	bus-width = <4>;
136 	non-removable;
141 		compatible = "brcm,bcm4329-fmac";
142 		interrupt-parent = <&pio>;
144 		interrupt-names = "host-wake";
169 		bias-pull-up;
174 	regulator-always-on;
175 	regulator-min-microvolt = <1000000>;
176 	regulator-max-microvolt = <1450000>;
177 	regulator-name = "vdd-cpu";
181 	regulator-always-on;
182 	regulator-min-microvolt = <1000000>;
183 	regulator-max-microvolt = <1400000>;
184 	regulator-name = "vdd-int-dll";
188 	regulator-name = "vdd-rtc";
192 	regulator-always-on;
193 	regulator-min-microvolt = <3000000>;
194 	regulator-max-microvolt = <3000000>;
195 	regulator-name = "avcc";
211 	pinctrl-names = "default";
212 	pinctrl-0 = <&uart0_pins_a>;
226 	pinctrl-names = "default";
227 	pinctrl-0 = <&usb0_id_detect_pin>;
228 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
229 	usb0_vbus_power-supply = <&usb_power_supply>;
230 	usb0_vbus-supply = <&reg_usb0_vbus>;
231 	usb1_vbus-supply = <&reg_usb1_vbus>;
232 	usb2_vbus-supply = <&reg_usb2_vbus>;