arm/dts/sun7i-a20-orangepi.dts

6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun7i-a20.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/interrupt-controller/irq.h>
54 	compatible = "xunlong,orangepi", "allwinner,sun7i-a20";
61 		stdout-path = "serial0:115200n8";
65 		compatible = "gpio-leds";
66 		pinctrl-names = "default";
67 		pinctrl-0 = <&led_pins_orangepi>;
75 	reg_gmac_3v3: gmac-3v3 {
76 		compatible = "regulator-fixed";
77 		pinctrl-names = "default";
78 		pinctrl-0 = <&gmac_power_pin_orangepi>;
79 		regulator-name = "gmac-3v3";
80 		regulator-min-microvolt = <3300000>;
81 		regulator-max-microvolt = <3300000>;
82 		startup-delay-us = <100000>;
83 		enable-active-high;
100 &gmac {
101 	pinctrl-names = "default";
102 	pinctrl-0 = <&gmac_pins_rgmii_a>;
104 	phy-mode = "rgmii";
105 	phy-supply = <&reg_gmac_3v3>;
108 	phy1: ethernet-phy@1 {
114 	pinctrl-names = "default";
115 	pinctrl-0 = <&i2c0_pins_a>;
120 		interrupt-parent = <&nmi_intc>;
128 	pinctrl-names = "default";
129 	pinctrl-0 = <&ir0_rx_pins_a>;
134 	pinctrl-names = "default";
135 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_orangepi>;
136 	vmmc-supply = <&reg_vcc3v3>;
137 	bus-width = <4>;
138 	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
150 		bias-pull-up;
156 		bias-pull-up;
181 	regulator-always-on;
182 	regulator-min-microvolt = <1000000>;
183 	regulator-max-microvolt = <1500000>;
184 	regulator-name = "vdd-cpu";
188 	regulator-always-on;
189 	regulator-min-microvolt = <1000000>;
190 	regulator-max-microvolt = <1400000>;
191 	regulator-name = "vdd-int-pll";
195 	regulator-name = "vdd-rtc";
199 	regulator-always-on;
200 	regulator-min-microvolt = <3000000>;
201 	regulator-max-microvolt = <3000000>;
202 	regulator-name = "avcc";
210 	pinctrl-0 = <&usb1_vbus_pin_bananapro>;
216 	pinctrl-0 = <&usb2_vbus_pin_bananapro>;
222 	pinctrl-names = "default";
223 	pinctrl-0 = <&uart0_pins_a>;
237 	pinctrl-names = "default";
238 	pinctrl-0 = <&usb0_id_detect_pin>;
239 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
240 	usb0_vbus_power-supply = <&usb_power_supply>;
241 	usb0_vbus-supply = <&reg_usb0_vbus>;
242 	usb1_vbus-supply = <&reg_usb1_vbus>;
243 	usb2_vbus-supply = <&reg_usb2_vbus>;