arm/dts/sun7i-a20-olinuxino-lime2.dts

2  * Copyright 2014 - Iain Paton <ipaton0@gmail.com>
4  * This file is dual-licensed: you can use it either under the terms
9  *  a) This file is free software; you can redistribute it and/or
43 /dts-v1/;
44 #include "sun7i-a20.dtsi"
45 #include "sunxi-common-regulators.dtsi"
47 #include <dt-bindings/gpio/gpio.h>
48 #include <dt-bindings/interrupt-controller/irq.h>
51 	model = "Olimex A20-OLinuXino-LIME2";
52 	compatible = "olimex,a20-olinuxino-lime2", "allwinner,sun7i-a20";
59 		stdout-path = "serial0:115200n8";
62 	hdmi-connector {
63 		compatible = "hdmi-connector";
68 				remote-endpoint = <&hdmi_out_con>;
74 		compatible = "gpio-leds";
75 		pinctrl-names = "default";
76 		pinctrl-0 = <&led_pins_olinuxinolime>;
79 			label = "a20-olinuxino-lime2:green:usr";
81 			default-state = "on";
86 		compatible = "regulator-fixed";
87 		regulator-name = "axp-ipsout";
88 		regulator-min-microvolt = <5000000>;
89 		regulator-max-microvolt = <5000000>;
90 		regulator-always-on;
95 	target-supply = <&reg_ahci_5v>;
112 	pinctrl-names = "default";
113 	pinctrl-0 = <&gmac_pins_rgmii_a>;
115 	phy-mode = "rgmii";
118 	phy1: ethernet-phy@1 {
129 		remote-endpoint = <&hdmi_con_in>;
134 	pinctrl-names = "default";
135 	pinctrl-0 = <&i2c0_pins_a>;
140 		interrupt-parent = <&nmi_intc>;
146 	pinctrl-names = "default";
147 	pinctrl-0 = <&i2c1_pins_a>;
158 	pinctrl-names = "default";
159 	pinctrl-0 = <&mmc0_pins_a>;
160 	vmmc-supply = <&reg_vcc3v3>;
161 	bus-width = <4>;
162 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
187 		drive-strength = <20>;
193 		bias-pull-up;
199 		bias-pull-down;
209 	pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
217 	regulator-always-on;
218 	regulator-min-microvolt = <1000000>;
219 	regulator-max-microvolt = <1400000>;
220 	regulator-name = "vdd-cpu";
224 	regulator-always-on;
225 	regulator-min-microvolt = <1000000>;
226 	regulator-max-microvolt = <1400000>;
227 	regulator-name = "vdd-int-dll";
231 	regulator-always-on;
232 	regulator-min-microvolt = <1300000>;
233 	regulator-max-microvolt = <1300000>;
234 	regulator-name = "vdd-rtc";
238 	regulator-always-on;
239 	regulator-min-microvolt = <3000000>;
240 	regulator-max-microvolt = <3000000>;
241 	regulator-name = "avcc";
245 	regulator-min-microvolt = <2800000>;
246 	regulator-max-microvolt = <2800000>;
247 	regulator-name = "vddio-csi0";
251 	regulator-min-microvolt = <2800000>;
252 	regulator-max-microvolt = <2800000>;
253 	regulator-name = "vddio-csi1";
257 	pinctrl-0 = <&usb0_vbus_pin_lime2>;
271 	pinctrl-names = "default";
272 	pinctrl-0 = <&uart0_pins_a>;
282 	pinctrl-names = "default";
283 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
284 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
285 	usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
286 	usb0_vbus-supply = <&reg_usb0_vbus>;
287 	usb1_vbus-supply = <&reg_usb1_vbus>;
288 	usb2_vbus-supply = <&reg_usb2_vbus>;