arm/dts/sun7i-a20-i12-tvbox.dts

4  * This file is dual-licensed: you can use it either under the terms
43 /dts-v1/;
44 #include "sun7i-a20.dtsi"
45 #include "sunxi-common-regulators.dtsi"
47 #include <dt-bindings/gpio/gpio.h>
48 #include <dt-bindings/interrupt-controller/irq.h>
51 	model = "I12 / Q5 / QT840A A20 tvbox";
52 	compatible = "allwinner,i12-tvbox", "allwinner,sun7i-a20";
59 		stdout-path = "serial0:115200n8";
63 		compatible = "gpio-leds";
64 		pinctrl-names = "default";
65 		pinctrl-0 = <&led_pins_i12_tvbox>;
79 		compatible = "regulator-fixed";
80 		pinctrl-names = "default";
81 		pinctrl-0 = <&vmmc3_pin_i12_tvbox>;
82 		regulator-name = "vmmc3";
83 		regulator-min-microvolt = <3300000>;
84 		regulator-max-microvolt = <3300000>;
85 		enable-active-high;
89 	reg_vmmc3_io: vmmc3-io {
90 		compatible = "regulator-fixed";
91 		pinctrl-names = "default";
92 		pinctrl-0 = <&vmmc3_io_pin_i12_tvbox>;
93 		regulator-name = "vmmc3-io";
94 		regulator-min-microvolt = <3300000>;
95 		regulator-max-microvolt = <3300000>;
96 		/* This controls VCC-PI, must be always on! */
97 		regulator-always-on;
98 		enable-active-high;
102 	reg_gmac_3v3: gmac-3v3 {
103 		compatible = "regulator-fixed";
104 		pinctrl-names = "default";
105 		pinctrl-0 = <&gmac_power_pin_i12_tvbox>;
106 		regulator-name = "gmac-3v3";
107 		regulator-min-microvolt = <3300000>;
108 		regulator-max-microvolt = <3300000>;
109 		startup-delay-us = <50000>;
110 		enable-active-high;
123 &gmac {
124 	pinctrl-names = "default";
125 	pinctrl-0 = <&gmac_pins_mii_a>;
127 	phy-mode = "mii";
128 	phy-supply = <&reg_gmac_3v3>;
131 	phy1: ethernet-phy@1 {
137 	pinctrl-names = "default";
138 	pinctrl-0 = <&i2c0_pins_a>;
142 		compatible = "x-powers,axp209";
144 		interrupt-parent = <&nmi_intc>;
147 		interrupt-controller;
148 		#interrupt-cells = <1>;
153 	pinctrl-names = "default";
154 	pinctrl-0 = <&ir0_rx_pins_a>;
159 	pinctrl-names = "default";
160 	pinctrl-0 = <&mmc0_pins_a>;
161 	vmmc-supply = <&reg_vcc3v3>;
162 	bus-width = <4>;
163 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
168 	pinctrl-names = "default";
169 	pinctrl-0 = <&mmc3_pins_a>;
170 	vmmc-supply = <&reg_vmmc3>;
171 	bus-width = <4>;
172 	non-removable;
177 		compatible = "brcm,bcm4329-fmac";
178 		interrupt-parent = <&pio>;
180 		interrupt-names = "host-wake";
185 	/* AP6210 / AP6330 requires pull-up */
186 	bias-pull-up;
228 	pinctrl-names = "default";
229 	pinctrl-0 = <&uart0_pins_a>;
234 	usb1_vbus-supply = <&reg_usb1_vbus>;
235 	usb2_vbus-supply = <&reg_usb2_vbus>;