arm/dts/sun7i-a20-bananapi.dts

6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun7i-a20.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/interrupt-controller/irq.h>
54 	compatible = "lemaker,bananapi", "allwinner,sun7i-a20";
63 		stdout-path = "serial0:115200n8";
66 	hdmi-connector {
67 		compatible = "hdmi-connector";
72 				remote-endpoint = <&hdmi_out_con>;
78 		compatible = "gpio-leds";
79 		pinctrl-names = "default";
80 		pinctrl-0 = <&led_pins_bananapi>;
88 	reg_gmac_3v3: gmac-3v3 {
89 		compatible = "regulator-fixed";
90 		pinctrl-names = "default";
91 		pinctrl-0 = <&gmac_power_pin_bananapi>;
92 		regulator-name = "gmac-3v3";
93 		regulator-min-microvolt = <3300000>;
94 		regulator-max-microvolt = <3300000>;
95 		startup-delay-us = <100000>;
96 		enable-active-high;
110 	cpu-supply = <&reg_dcdc2>;
111 	operating-points = <
135 &gmac {
136 	pinctrl-names = "default";
137 	pinctrl-0 = <&gmac_pins_rgmii_a>;
139 	phy-mode = "rgmii";
140 	phy-supply = <&reg_gmac_3v3>;
143 	phy1: ethernet-phy@1 {
154 		remote-endpoint = <&hdmi_con_in>;
159 	pinctrl-names = "default";
160 	pinctrl-0 = <&i2c0_pins_a>;
165 		interrupt-parent = <&nmi_intc>;
171 	pinctrl-names = "default";
172 	pinctrl-0 = <&i2c2_pins_a>;
177 	pinctrl-names = "default";
178 	pinctrl-0 = <&ir0_rx_pins_a>;
183 	pinctrl-names = "default";
184 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
185 	vmmc-supply = <&reg_vcc3v3>;
186 	bus-width = <4>;
187 	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
204 	gpio-line-names =
213 		"PMU-SCK", "PMU-SDA", "", "", "", "", "", "",
214 		"", "USB0-DRV", "", "", "", "", "", "",
233 		"SD0-D1", "SD0-D0", "SD0-CLK", "SD0-CMD", "SD0-D3",
234 			"SD0-D2", "", "",
244 		"TXD0", "RXD0", "IO-1", "PH3", "USB0-IDDET", "PH5", "", "",
245 		"", "", "SD0-DET", "", "", "", "", "",
246 		"", "", "", "", "IO-4", "IO-5", "", "EMAC-PWR-EN",
249 		"", "", "", "IO-GCLK", "", "", "", "",
250 		"", "", "SPI-CE0", "SPI-CLK", "SPI-MOSI",
251 			"SPI-MISO", "SPI-CE1", "",
252 		"IO-6", "IO-3", "IO-2", "IO-0", "", "", "", "",
258 		bias-pull-up;
264 		bias-pull-up;
281 	regulator-always-on;
282 	regulator-min-microvolt = <1000000>;
283 	regulator-max-microvolt = <1400000>;
284 	regulator-name = "vdd-cpu";
288 	regulator-always-on;
289 	regulator-min-microvolt = <1000000>;
290 	regulator-max-microvolt = <1400000>;
291 	regulator-name = "vdd-int-dll";
295 	regulator-name = "vdd-rtc";
299 	regulator-always-on;
300 	regulator-min-microvolt = <3000000>;
301 	regulator-max-microvolt = <3000000>;
302 	regulator-name = "avcc";
318 	pinctrl-names = "default";
319 	pinctrl-0 = <&spi0_pins_a>,
326 	pinctrl-names = "default";
327 	pinctrl-0 = <&uart0_pins_a>;
332 	pinctrl-names = "default";
333 	pinctrl-0 = <&uart3_pins_b>;
338 	pinctrl-names = "default";
339 	pinctrl-0 = <&uart7_pins_a>;
353 	pinctrl-names = "default";
354 	pinctrl-0 = <&usb0_id_detect_pin>;
355 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
356 	usb0_vbus_power-supply = <&usb_power_supply>;
357 	usb0_vbus-supply = <&reg_usb0_vbus>;
358 	usb1_vbus-supply = <&reg_usb1_vbus>;
359 	usb2_vbus-supply = <&reg_usb2_vbus>;