arm/dts/sun5i-a13-empire-electronix-d709.dts

4  * This file is dual-licensed: you can use it either under the terms
43 /dts-v1/;
44 #include "sun5i-a13.dtsi"
45 #include "sunxi-common-regulators.dtsi"
46 #include <dt-bindings/gpio/gpio.h>
47 #include <dt-bindings/input/input.h>
48 #include <dt-bindings/interrupt-controller/irq.h>
49 #include <dt-bindings/pwm/pwm.h>
52 	model = "Empire Electronix D709 tablet";
53 	compatible = "empire-electronix,d709", "allwinner,sun5i-a13";
60 		compatible = "pwm-backlight";
62 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
63 		default-brightness-level = <8>;
68 		stdout-path = "serial0:115200n8";
73 	cpu-supply = <&reg_dcdc2>;
81 	pinctrl-names = "default";
82 	pinctrl-0 = <&i2c0_pins_a>;
94 	pinctrl-names = "default";
95 	pinctrl-0 = <&i2c1_pins_a>;
105 	vref-supply = <&reg_ldo2>;
124 	pinctrl-names = "default";
125 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
126 	vmmc-supply = <&reg_vcc3v3>;
127 	bus-width = <4>;
128 	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
140 		bias-pull-up;
146 		bias-pull-down;
152 		bias-pull-up;
157 	pinctrl-names = "default";
158 	pinctrl-0 = <&pwm0_pins>;
163 	regulator-always-on;
164 	regulator-min-microvolt = <1000000>;
165 	regulator-max-microvolt = <1400000>;
166 	regulator-name = "vdd-cpu";
170 	regulator-always-on;
171 	regulator-min-microvolt = <1250000>;
172 	regulator-max-microvolt = <1250000>;
173 	regulator-name = "vdd-int-pll";
177 	regulator-name = "vdd-rtc";
181 	regulator-always-on;
182 	regulator-min-microvolt = <3000000>;
183 	regulator-max-microvolt = <3000000>;
184 	regulator-name = "avcc";
188 	regulator-min-microvolt = <3300000>;
189 	regulator-max-microvolt = <3300000>;
190 	regulator-name = "vcc-wifi";
199 	pinctrl-names = "default";
200 	pinctrl-0 = <&uart1_pins_b>;
210 	pinctrl-names = "default";
211 	pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
212 	usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
213 	usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
214 	usb0_vbus-supply = <&reg_usb0_vbus>;
215 	usb1_vbus-supply = <&reg_ldo3>;