arm/dts/sun5i-a10s-olinuxino-micro.dts

4  * Maxime Ripard <maxime.ripard@free-electrons.com>
6  * This file is dual-licensed: you can use it either under the terms
45 /dts-v1/;
46 #include "sun5i-a10s.dtsi"
47 #include "sunxi-common-regulators.dtsi"
49 #include <dt-bindings/gpio/gpio.h>
50 #include <dt-bindings/input/input.h>
53 	model = "Olimex A10s-Olinuxino Micro";
54 	compatible = "olimex,a10s-olinuxino-micro", "allwinner,sun5i-a10s";
63 		stdout-path = "serial0:115200n8";
67 		compatible = "hdmi-connector";
72 				remote-endpoint = <&hdmi_out_con>;
78 		compatible = "gpio-leds";
79 		pinctrl-names = "default";
80 		pinctrl-0 = <&led_pins_olinuxino>;
83 			label = "a10s-olinuxino-micro:green:usr";
85 			default-state = "on";
99 	pinctrl-names = "default";
100 	pinctrl-0 = <&emac_pins_b>;
115 		remote-endpoint = <&hdmi_con_in>;
120 	pinctrl-names = "default";
121 	pinctrl-0 = <&i2c0_pins_a>;
133 	pinctrl-names = "default";
134 	pinctrl-0 = <&i2c1_pins_a>;
141 		read-only;
146 	pinctrl-names = "default";
147 	pinctrl-0 = <&i2c2_pins_a>;
152 	vref-supply = <&reg_vcc3v0>;
155 	button@191 {
162 	button@392 {
169 	button@601 {
176 	button@795 {
183 	button@987 {
194 	phy1: ethernet-phy@1 {
200 	pinctrl-names = "default";
201 	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_olinuxino_micro>;
202 	vmmc-supply = <&reg_vcc3v3>;
203 	bus-width = <4>;
204 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
209 	pinctrl-names = "default";
210 	pinctrl-0 = <&mmc1_pins_a>, <&mmc1_cd_pin_olinuxino_micro>;
211 	vmmc-supply = <&reg_vcc3v3>;
212 	bus-width = <4>;
213 	cd-gpios = <&pio 6 13 GPIO_ACTIVE_LOW>; /* PG13 */
229 		bias-pull-up;
235 		bias-pull-up;
241 		drive-strength = <20>;
252 		bias-pull-up;
262 	pinctrl-0 = <&usb1_vbus_pin_olinuxino_m>;
268 	pinctrl-names = "default";
269 	pinctrl-0 = <&spi2_pins_b>,
279 	pinctrl-names = "default";
280 	pinctrl-0 = <&uart0_pins_a>;
285 	pinctrl-names = "default";
286 	pinctrl-0 = <&uart2_pins_b>;
291 	pinctrl-names = "default";
292 	pinctrl-0 = <&uart3_pins_a>;
302 	pinctrl-names = "default";
303 	pinctrl-0 = <&usb0_id_detect_pin>;
304 	usb0_id_det-gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
305 	usb0_vbus-supply = <&reg_usb0_vbus>;
306 	usb1_vbus-supply = <&reg_usb1_vbus>;