arm/dts/stm32429i-eval.dts

1 // SPDX-License-Identifier: GPL-2.0+
3  * Copyright (C) 2015, STMicroelectronics - All Rights Reserved
7 /dts-v1/;
9 #include "stm32f429-pinctrl.dtsi"
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/gpio/gpio.h>
14 	model = "STMicroelectronics STM32429i-EVAL board";
15 	compatible = "st,stm32429i-eval", "st,stm32f429";
19 		stdout-path = "serial0:115200n8";
31 		clk_ext_camera: clk-ext-camera {
32 			#clock-cells = <0>;
33 			compatible = "fixed-clock";
34 			clock-frequency = <24000000>;
39 		dma-ranges = <0xc0000000 0x0 0x10000000>;
43 		compatible = "simple-bus";
44 		#address-cells = <1>;
45 		#size-cells = <0>;
48 			compatible = "regulator-fixed";
50 			regulator-name = "vref";
51 			regulator-min-microvolt = <3300000>;
52 			regulator-max-microvolt = <3300000>;
57 		compatible = "gpio-leds";
59 			gpios = <&gpiog 6 1>;
60 			linux,default-trigger = "heartbeat";
63 			gpios = <&gpiog 7 1>;
66 			gpios = <&gpiog 10 1>;
69 			gpios = <&gpiog 12 1>;
74 		compatible = "gpio-keys";
75 		#size-cells = <0>;
80 			gpios = <&gpioa 0 0>;
85 			gpios = <&gpioc 13 0>;
90 		#phy-cells = <0>;
91 		compatible = "usb-nop-xceiv";
93 		clock-names = "main_clk";
96 	panel_rgb: panel-rgb {
97 		compatible = "ampire,am-480272h3tmqw-t01h";
101 				remote-endpoint = <&ltdc_out_rgb>;
107 		compatible = "regulator-fixed";
108 		regulator-name = "mmc_vcard";
109 		regulator-min-microvolt = <3300000>;
110 		regulator-max-microvolt = <3300000>;
115 	pinctrl-names = "default";
116 	pinctrl-0 = <&adc3_in8_pin>;
117 	vref-supply = <&reg_vref>;
120 		st,adc-channels = <8>;
126 	clock-frequency = <25000000>;
138 			remote-endpoint = <&ov2640_0>;
139 			bus-width = <8>;
140 			hsync-active = <0>;
141 			vsync-active = <0>;
142 			pclk-sample = <1>;
148 	pinctrl-0 = <&i2c1_pins>;
149 	pinctrl-names = "default";
155 		resetb-gpios = <&stmpegpio 2 GPIO_ACTIVE_HIGH>;
156 		pwdn-gpios = <&stmpegpio 0 GPIO_ACTIVE_LOW>;
158 		clock-names = "xvclk";
163 				remote-endpoint = <&dcmi_0>;
172 		interrupt-parent = <&gpioi>;
173 		interrupt-controller;
174 		wakeup-source;
177 			compatible = "st,stmpe-gpio";
178 			gpio-controller;
179 			#gpio-cells = <2>;
186 	timeout-sec = <32>;
191 	pinctrl-0 = <&ltdc_pins>;
192 	pinctrl-names = "default";
193 	dma-ranges;
197 			remote-endpoint = <&panel_in_rgb>;
204 	pinctrl-0	= <&ethernet_mii>;
205 	pinctrl-names	= "default";
206 	phy-mode	= "mii";
207 	phy-handle	= <&phy1>;
209 		#address-cells = <1>;
210 		#size-cells = <0>;
211 		compatible = "snps,dwmac-mdio";
212 		phy1: ethernet-phy@1 {
224 	vmmc-supply = <&mmc_vcard>;
225 	cd-gpios = <&stmpegpio 15 GPIO_ACTIVE_LOW>;
226 	pinctrl-names = "default", "opendrain";
227 	pinctrl-0 = <&sdio_pins>;
228 	pinctrl-1 = <&sdio_pins_od>;
229 	bus-width = <4>;
230 	max-frequency = <14000000>;
237 		pinctrl-0 = <&pwm1_pins>;
238 		pinctrl-names = "default";
251 		pinctrl-0 = <&pwm3_pins>;
252 		pinctrl-names = "default";
262 	pinctrl-0 = <&usart1_pins_a>;
263 	pinctrl-names = "default";
270 	phy-names = "usb2-phy";
271 	pinctrl-0 = <&usbotg_hs_pins_a>;
272 	pinctrl-names = "default";