arm/dts/sama5d3xmb_cmp.dtsi

2  * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
14 		u-boot,dm-pre-reloc;
15 		stdout-path = &dbgu;
21 				pinctrl-names = "default";
22 				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
26 					bus-width = <4>;
27 					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
32 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
35 					compatible = "spi-flash";
36 					spi-max-frequency = <50000000>;
42 				atmel,clk-from-rk-pin;
47 			 * disable it to allow the use of ISI
55 					clock-names = "mclk";
63 					pinctrl-names = "default";
64 					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
65 					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
66 					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
67 					/* use pck1 for the master clock of ov2640 */
69 					clock-names = "xvclk";
70 					assigned-clocks = <&pck1>;
71 					assigned-clock-rates = <25000000>;
75 							remote-endpoint = <&isi_0>;
76 							bus-width = <8>;
83 				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
84 				pinctrl-names = "default";
85 				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
92 						remote-endpoint = <&ov2640_0>;
93 						bus-width = <8>;
94 						vsync-active = <1>;
95 						hsync-active = <1>;
101 				pinctrl-names = "default";
102 				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
106 					bus-width = <4>;
107 					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
112 				pinctrl-names = "default";
113 				pinctrl-0 = <
125 				phy-mode = "rmii";
127 				#address-cells = <1>;
128 				#size-cells = <0>;
129 				phy0: ethernet-phy@1 {
130 					/*interrupt-parent = <&pioE>;*/
136 			pinctrl@fffff200 {
158 					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
163 					pinctrl_sensor_reset: sensor_reset-0 {
168 					pinctrl_sensor_power: sensor_power-0 {
181 				dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
183 				u-boot,dm-pre-reloc;
192 			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
193 			pinctrl-names = "default";
194 			pinctrl-0 = <&pinctrl_usba_vbus>;
200 		compatible = "atmel,asoc-wm8904";
201 		pinctrl-names = "default";
202 		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
205 		atmel,audio-routing =
213 		atmel,ssc-controller = <&ssc0>;
214 		atmel,audio-codec = <&wm8904>;
221 		compatible = "gpio-keys";
224 		pinctrl-names = "default";
225 		pinctrl-0 = <&pinctrl_gpio_keys>;
231 			gpio-key,wakeup;