arm/dts/sama5d3xmb.dtsi

2  * sama5d3xmb.dts - Device Tree file for SAMA5D3x mother board
15 		u-boot,dm-pre-reloc;
16 		stdout-path = &dbgu;
22 				pinctrl-names = "default";
23 				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
25 				u-boot,dm-pre-reloc;
28 					bus-width = <4>;
29 					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
35 				u-boot,dm-pre-reloc;
38 					compatible = "spi-flash";
39 					spi-max-frequency = <50000000>;
41 					u-boot,dm-pre-reloc;
46 				atmel,clk-from-rk-pin;
59 					clock-names = "mclk";
67 					pinctrl-names = "default";
68 					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
69 					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
70 					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
73 					clock-names = "xvclk";
74 					assigned-clocks = <&pck1>;
75 					assigned-clock-rates = <25000000>;
79 							remote-endpoint = <&isi_0>;
80 							bus-width = <8>;
88 				pinctrl-names = "default";
89 				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
96 						remote-endpoint = <&ov2640_0>;
97 						bus-width = <8>;
98 						vsync-active = <1>;
99 						hsync-active = <1>;
105 				pinctrl-names = "default";
106 				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
108 				u-boot,dm-pre-reloc;
111 					bus-width = <4>;
112 					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
117 				pinctrl-names = "default";
118 				pinctrl-0 = <
130 				phy-mode = "rmii";
132 				#address-cells = <1>;
133 				#size-cells = <0>;
134 				phy0: ethernet-phy@1 {
135 					/*interrupt-parent = <&pioE>;*/
143 					u-boot,dm-pre-reloc;
145 						u-boot,dm-pre-reloc;
151 						u-boot,dm-pre-reloc;
161 					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
166 					pinctrl_sensor_reset: sensor_reset-0 {
171 					pinctrl_sensor_power: sensor_power-0 {
186 				u-boot,dm-pre-reloc;
195 			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
196 			pinctrl-names = "default";
197 			pinctrl-0 = <&pinctrl_usba_vbus>;
202 			num-ports = <3>;
203 			atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH
216 		compatible = "atmel,asoc-wm8904";
217 		pinctrl-names = "default";
218 		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
221 		atmel,audio-routing =
229 		atmel,ssc-controller = <&ssc0>;
230 		atmel,audio-codec = <&wm8904>;