arm/dts/salvator-common.dtsi

1 // SPDX-License-Identifier: GPL-2.0
3  * Device Tree Source for common parts of Salvator-X board variants
5  * Copyright (C) 2015-2016 Renesas Electronics Corp.
9  * SSI-AK4613
31 #include <dt-bindings/gpio/gpio.h>
42 		stdout-path = "serial0:115200n8";
45 	audio_clkout: audio-clkout {
48 		 * but needed to avoid cs2000/rcar_sound probe dead-lock
50 		compatible = "fixed-clock";
51 		#clock-cells = <0>;
52 		clock-frequency = <12288000>;
56 		compatible = "pwm-backlight";
59 		brightness-levels = <256 128 64 16 8 4 0>;
60 		default-brightness-level = <6>;
62 		power-supply = <&reg_12v>;
63 		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
66 	cvbs-in {
67 		compatible = "composite-video-connector";
72 				remote-endpoint = <&adv7482_ain7>;
77 	hdmi-in {
78 		compatible = "hdmi-connector";
84 				remote-endpoint = <&adv7482_hdmi>;
90 		compatible = "regulator-fixed";
91 		regulator-name = "fixed-1.8V";
92 		regulator-min-microvolt = <1800000>;
93 		regulator-max-microvolt = <1800000>;
94 		regulator-boot-on;
95 		regulator-always-on;
99 		compatible = "regulator-fixed";
100 		regulator-name = "fixed-3.3V";
101 		regulator-min-microvolt = <3300000>;
102 		regulator-max-microvolt = <3300000>;
103 		regulator-boot-on;
104 		regulator-always-on;
108 		compatible = "regulator-fixed";
109 		regulator-name = "fixed-12V";
110 		regulator-min-microvolt = <12000000>;
111 		regulator-max-microvolt = <12000000>;
112 		regulator-boot-on;
113 		regulator-always-on;
117 		compatible = "audio-graph-card";
119 		label = "rcar-sound";
124 	vbus0_usb2: regulator-vbus0-usb2 {
125 		compatible = "regulator-fixed";
127 		regulator-name = "USB20_VBUS0";
128 		regulator-min-microvolt = <5000000>;
129 		regulator-max-microvolt = <5000000>;
132 		enable-active-high;
135 	vcc_sdhi0: regulator-vcc-sdhi0 {
136 		compatible = "regulator-fixed";
138 		regulator-name = "SDHI0 Vcc";
139 		regulator-min-microvolt = <3300000>;
140 		regulator-max-microvolt = <3300000>;
143 		enable-active-high;
146 	vccq_sdhi0: regulator-vccq-sdhi0 {
147 		compatible = "regulator-gpio";
149 		regulator-name = "SDHI0 VccQ";
150 		regulator-min-microvolt = <1800000>;
151 		regulator-max-microvolt = <3300000>;
154 		gpios-states = <1>;
159 	vcc_sdhi3: regulator-vcc-sdhi3 {
160 		compatible = "regulator-fixed";
162 		regulator-name = "SDHI3 Vcc";
163 		regulator-min-microvolt = <3300000>;
164 		regulator-max-microvolt = <3300000>;
167 		enable-active-high;
170 	vccq_sdhi3: regulator-vccq-sdhi3 {
171 		compatible = "regulator-gpio";
173 		regulator-name = "SDHI3 VccQ";
174 		regulator-min-microvolt = <1800000>;
175 		regulator-max-microvolt = <3300000>;
178 		gpios-states = <1>;
183 	hdmi0-out {
184 		compatible = "hdmi-connector";
194 	hdmi1-out {
195 		compatible = "hdmi-connector";
206 		compatible = "vga-connector";
210 				remote-endpoint = <&adv7123_out>;
215 	vga-encoder {
219 			#address-cells = <1>;
220 			#size-cells = <0>;
225 					remote-endpoint = <&du_out_rgb>;
231 					remote-endpoint = <&vga_in>;
238 		compatible = "fixed-clock";
239 		#clock-cells = <0>;
240 		clock-frequency = <24576000>;
244 	x21_clk: x21-clock {
245 		compatible = "fixed-clock";
246 		#clock-cells = <0>;
247 		clock-frequency = <33000000>;
250 	x22_clk: x22-clock {
251 		compatible = "fixed-clock";
252 		#clock-cells = <0>;
253 		clock-frequency = <33000000>;
256 	x23_clk: x23-clock {
257 		compatible = "fixed-clock";
258 		#clock-cells = <0>;
259 		clock-frequency = <25000000>;
264 	clock-frequency = <22579200>;
268 	pinctrl-0 = <&avb_pins>;
269 	pinctrl-names = "default";
270 	phy-handle = <&phy0>;
271 	phy-mode = "rgmii-txid";
274 	phy0: ethernet-phy@0 {
275 		rxc-skew-ps = <1500>;
277 		interrupt-parent = <&gpio2>;
279 		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
290 				clock-lanes = <0>;
291 				data-lanes = <1>;
292 				remote-endpoint = <&adv7482_txb>;
306 				clock-lanes = <0>;
307 				data-lanes = <1 2 3 4>;
308 				remote-endpoint = <&adv7482_txa>;
315 	pinctrl-0 = <&du_pins>;
316 	pinctrl-names = "default";
322 				remote-endpoint = <&adv7123_in>;
338 	clock-frequency = <32768>;
342 	pinctrl-0 = <&hscif1_pins>;
343 	pinctrl-names = "default";
345 	uart-has-rtscts;
356 	pinctrl-0 = <&i2c2_pins>;
357 	pinctrl-names = "default";
361 	clock-frequency = <100000>;
364 		compatible = "asahi-kasei,ak4613";
365 		#sound-dai-cells = <0>;
369 		asahi-kasei,in1-single-end;
370 		asahi-kasei,in2-single-end;
371 		asahi-kasei,out1-single-end;
372 		asahi-kasei,out2-single-end;
373 		asahi-kasei,out3-single-end;
374 		asahi-kasei,out4-single-end;
375 		asahi-kasei,out5-single-end;
376 		asahi-kasei,out6-single-end;
380 				remote-endpoint = <&rsnd_endpoint0>;
386 		#clock-cells = <0>;
387 		compatible = "cirrus,cs2000-cp";
390 		clock-names = "clk_in", "ref_clk";
392 		assigned-clocks = <&cs2000>;
393 		assigned-clock-rates = <24576000>; /* 1/1 divide */
403 		gpio-controller;
404 		#gpio-cells = <2>;
411 		shunt-resistor-micro-ohms = <5000>;
418 		shunt-resistor-micro-ohms = <5000>;
421 	video-receiver@70 {
425 		#address-cells = <1>;
426 		#size-cells = <0>;
428 		interrupt-parent = <&gpio6>;
429 		interrupt-names = "intrq1", "intrq2";
437 				remote-endpoint = <&cvbs_con>;
445 				remote-endpoint = <&hdmi_in_con>;
453 				clock-lanes = <0>;
454 				data-lanes = <1 2 3 4>;
455 				remote-endpoint = <&csi40_in>;
463 				clock-lanes = <0>;
464 				data-lanes = <1>;
465 				remote-endpoint = <&csi20_in>;
475 		pinctrl-0 = <&irq0_pins>;
476 		pinctrl-names = "default";
480 		interrupt-parent = <&intc_ex>;
482 		interrupt-controller;
483 		#interrupt-cells = <2>;
484 		gpio-controller;
485 		#gpio-cells = <2>;
486 		rohm,ddr-backup-power = <0xf>;
487 		rohm,rstbmode-level;
491 				regulator-name = "dvfs";
492 				regulator-min-microvolt = <750000>;
493 				regulator-max-microvolt = <1030000>;
494 				regulator-boot-on;
495 				regulator-always-on;
517 	clock-frequency = <100000000>;
529 	pinctrl-0 = <&scif_clk_pins>;
530 	pinctrl-names = "default";
540 			drive-strength = <24>;
546 			drive-strength = <12>;
593 		power-source = <3300>;
599 		power-source = <1800>;
605 		power-source = <3300>;
611 		power-source = <1800>;
617 		power-source = <3300>;
623 		power-source = <1800>;
650 			bias-pull-up;
655 			bias-pull-down;
666 	pinctrl-0 = <&pwm1_pins>;
667 	pinctrl-names = "default";
673 	pinctrl-0 = <&sound_pins &sound_clk_pins>;
674 	pinctrl-names = "default";
677 	#sound-dai-cells = <0>;
680 	#clock-cells = <1>;
681 	clock-frequency = <12288000 11289600>;
707 				remote-endpoint = <&ak4613_endpoint>;
709 				dai-format = "left_j";
710 				bitclock-master = <&rsnd_endpoint0>;
711 				frame-master = <&rsnd_endpoint0>;
721 	pinctrl-0 = <&scif1_pins>;
722 	pinctrl-names = "default";
724 	uart-has-rtscts;
730 	pinctrl-0 = <&scif2_pins>;
731 	pinctrl-names = "default";
737 	clock-frequency = <14745600>;
741 	pinctrl-0 = <&sdhi0_pins>;
742 	pinctrl-1 = <&sdhi0_pins_uhs>;
743 	pinctrl-names = "default", "state_uhs";
745 	vmmc-supply = <&vcc_sdhi0>;
746 	vqmmc-supply = <&vccq_sdhi0>;
747 	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
748 	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
749 	bus-width = <4>;
750 	sd-uhs-sdr50;
755 	/* used for on-board 8bit eMMC */
756 	pinctrl-0 = <&sdhi2_pins>;
757 	pinctrl-1 = <&sdhi2_pins_uhs>;
758 	pinctrl-names = "default", "state_uhs";
760 	vmmc-supply = <&reg_3p3v>;
761 	vqmmc-supply = <&reg_1p8v>;
762 	bus-width = <8>;
763 	mmc-hs200-1_8v;
764 	non-removable;
765 	fixed-emmc-driver-type = <1>;
770 	pinctrl-0 = <&sdhi3_pins>;
771 	pinctrl-1 = <&sdhi3_pins_uhs>;
772 	pinctrl-names = "default", "state_uhs";
774 	vmmc-supply = <&vcc_sdhi3>;
775 	vqmmc-supply = <&vccq_sdhi3>;
776 	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
777 	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
778 	bus-width = <4>;
779 	sd-uhs-sdr50;
784 	shared-pin;
788 	clock-frequency = <50000000>;
792 	pinctrl-0 = <&usb0_pins>;
793 	pinctrl-names = "default";
795 	vbus-supply = <&vbus0_usb2>;
800 	pinctrl-0 = <&usb1_pins>;
801 	pinctrl-names = "default";
808 	phy-names = "usb";
818 	clock-frequency = <100000000>;
845 &vin6 {
854 	timeout-sec = <60>;
859 	pinctrl-0 = <&usb30_pins>;
860 	pinctrl-names = "default";