arm/dts/hi3798cv200-poplar.dts

4  * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
7  * SPDX-License-Identifier: GPL-2.0
10 /dts-v1/;
12 #include <dt-bindings/gpio/gpio.h>
14 #include "poplar-pinctrl.dtsi"
18 	compatible = "hisilicon,hi3798cv200-poplar", "hisilicon,hi3798cv200";
21 		serial0 = &uart0;
26 		stdout-path = "serial0:115200n8";
36 			compatible = "linaro,optee-tz";
42 		compatible = "gpio-leds";
44 		user-led0 {
45 			label = "USER-LED0";
47 			linux,default-trigger = "heartbeat";
48 			default-state = "off";
51 		user-led1 {
52 			label = "USER-LED1";
54 			linux,default-trigger = "mmc0";
55 			default-state = "off";
58 		user-led2 {
59 			label = "USER-LED2";
61 			linux,default-trigger = "none";
62 			default-state = "off";
65 		user-led3 {
66 			label = "USER-LED3";
68 			linux,default-trigger = "cpu0";
69 			default-state = "off";
73 	reg_pcie: regulator-pcie {
74 		compatible = "regulator-fixed";
75 		regulator-name = "3V3_PCIE0";
76 		regulator-min-microvolt = <3300000>;
77 		regulator-max-microvolt = <3300000>;
79 		enable-active-high;
88 	pinctrl-names = "default";
89 	pinctrl-0 = <&emmc_pins_1 &emmc_pins_2
91 	fifo-depth = <256>;
92 	clock-frequency = <200000000>;
93 	cap-mmc-highspeed;
94 	mmc-ddr-1_8v;
95 	mmc-hs200-1_8v;
96 	non-removable;
97 	bus-width = <8>;
103 	#address-cells = <1>;
104 	#size-cells = <0>;
105 	phy-handle = <&eth_phy1>;
106 	phy-mode = "rgmii";
107 	hisilicon,phy-reset-delays-us = <10000 10000 30000>;
116 	gpio-line-names = "GPIO-E",	"",
118 			  "",		"GPIO-F",
119 			  "",		"GPIO-J";
124 	gpio-line-names = "GPIO-H",	"GPIO-I",
125 			  "GPIO-L",	"GPIO-G",
126 			  "GPIO-K",	"",
132 	gpio-line-names = "",		"",
134 			  "GPIO-C",	"",
135 			  "",		"GPIO-B";
140 	gpio-line-names = "",		"",
142 			  "",		"GPIO-D",
148 	gpio-line-names = "",		"USER-LED-1",
149 			  "USER-LED-2",	"",
150 			  "",		"GPIO-A",
156 	gpio-line-names = "",		"",
157 			  "",		"USER-LED-0",
164 	gpio-line-names = "",		"",
167 			  "USER-LED-3",	"";
172 	label = "LS-I2C0";
177 	label = "LS-I2C1";
189 	reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
190 	vpcie-supply = <&reg_pcie>;
195 	bus-width = <4>;
196 	cap-sd-highspeed;
202 	label = "LS-SPI0";
211 	label = "LS-UART0";
213 /* No optional LS-UART1 on Low Speed Expansion Connector. */