Lines Matching +full:0 +full:x04

35 		pwms = <&pwm 0 1000000 0>;
36 		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
66 			reg = <0x9>;
77 			sound-dai = <&i2s0 0>;
81 			sound-dai = <&max98090 0>;
88 			reg = <0x10>;
95 			reg = <0x48>;
99 				0x02 0xa1 0x01  /* HPD low */
102 				* [1:0] SW output 1.2V voltage is lower to 96%
104 				0x04 0x14 0x01
109 				0x04 0xe3 0x20
110 				0x04 0xe2 0x80 /* [7] RCO SS enable */
117 				0x04 0x8a 0x0c
118 				0x04 0x89 0x08 /* [3] RFD always on */
124 				0x04 0x71 0x2d
129 				0x04 0x7d 0x07
130 				0x04 0x7b 0x00  /* [1:0] Fmin=+4bands */
131 				0x04 0x7a 0xfd  /* [7:5] DCO_FTRNG=+-40% */
134 				* [5:2]NOF=64LSB [1:0]DCO scale is 2/5
136 				0x04 0xc0 0x12
137 				0x04 0xc1 0x92  /* Gitune=-37% */
138 				0x04 0xc2 0x1c  /* Fbstep=100% */
139 				0x04 0x32 0x80  /* [7]LOS signal disable */
145 				0x04 0x00 0xb0
149 				0x04 0x15 0x40
151 				0x04 0x54 0x10  /* RCO calibration start */
152 				/* [4:0] MAX_LANE_COUNT set to one lane */
153 				0x01 0x02 0x81
154 				/* [4:0] LANE_COUNT_SET set to one lane */
155 				0x01 0x21 0x81
156 				0x00 0x52 0x20
157 				0x00 0xf1 0x03  /* HPD CP toggle enable */
158 				0x00 0x62 0x41
160 				0x00 0xf6 0x01
166 				0x00 0x77 0x06
171 				0x00 0x4c 0x04
173 				0x01 0xc0 0x00
174 				0x01 0xc1 0x1c  /* DPCD00401='h1c */
175 				0x01 0xc2 0xf8  /* DPCD00402='hf8 */
180 				0x01 0xc3 0x44
181 				0x01 0xc4 0x32  /* DPCD404 */
182 				0x01 0xc5 0x53  /* DPCD405 */
183 				0x01 0xc6 0x4c  /* DPCD406 */
184 				0x01 0xc7 0x56  /* DPCD407 */
185 				0x01 0xc8 0x35  /* DPCD408 */
190 				0x01 0xca 0x01
192 				0x01 0xcb 0x05
194 				0x01 0xa5 0xa0
196 				* FFh for 100% PWM of brightness, 0h for 0%
199 				0x01 0xa7 0xff
204 				0x01 0xcc 0x13
206 				0x02 0xb1 0x20
211 				0x04 0x10 0x16
213 				0x04 0x59 0x60
214 				0x04 0x54 0x14  /* LC -> RCO */
215 				0x02 0xa1 0x91>;  /* HPD high */
218 				port@0 {
241 			reg = <0x20>;
259 		firmware_storage_spi: flash@0 {
261 			reg = <0>;
267 			elog-panic-event-offset = <0x01e00000 0x100000>;
269 			elog-shrink-size = <0x400>;
270 			elog-full-threshold = <0xc00>;
275 		samsung,vbus-gpio = <&gph0 0 GPIO_ACTIVE_HIGH>;
299 		samsung,vl-cmd-allow-len = <0xf>;
304 		samsung,dual-lcd-enabled = <0>;
310 	samsung,color-space = <0>;
311 	samsung,dynamic-range = <0>;
312 	samsung,ycbcr-coeff = <0>;
314 	samsung,link-rate = <0x06>;
319 		port@0 {
332 	samsung,spi-src-clk = <0>;
333 	cs-gpios = <&gpb1 2 0>;
335 	cros_ec: cros-ec@0 {
338 		interrupts = <5 0>;
339 		reg = <0>;
348 		 * that the STM32L flash erases to 0, not 0xff.
351 			reg = <0x08000000 0x20000>;
352 			erase-value = <0>;
362 			#size-cells = <0>;
363 			google,remote-bus = <0>;
367 				reg = <0xb>;
374 				reg = <0x48>;