Lines Matching +full:serial +full:- +full:pins
2 * at91-sama5d3_xplained.dts - Device Tree file for the SAMA5D3 Xplained board
9 /dts-v1/;
14 compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
17 u-boot,dm-pre-reloc;
18 stdout-path = &dbgu;
31 clock-frequency = <32768>;
35 clock-frequency = <12000000>;
41 pinctrl-names = "default";
42 pinctrl-0 = <&pinctrl_onewire_tm_default>;
54 u-boot,dm-pre-reloc;
55 …pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd…
56 vmmc-supply = <&vcc_mmc0_reg>;
57 vqmmc-supply = <&vcc_3v3_reg>;
61 bus-width = <8>;
62 cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
67 u-boot,dm-pre-reloc;
68 vmmc-supply = <&vcc_3v3_reg>;
69 vqmmc-supply = <&vcc_3v3_reg>;
73 bus-width = <4>;
74 cd-gpios = <&pioE 1 GPIO_ACTIVE_LOW>;
79 cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
88 pinctrl-0 = <&pinctrl_i2c0_pu>;
96 compatible = "active-semi,act8865";
102 regulator-name = "VCC_1V8";
103 regulator-min-microvolt = <1800000>;
104 regulator-max-microvolt = <1800000>;
105 regulator-always-on;
109 regulator-name = "VCC_1V2";
110 regulator-min-microvolt = <1200000>;
111 regulator-max-microvolt = <1200000>;
112 regulator-always-on;
116 regulator-name = "VCC_3V3";
117 regulator-min-microvolt = <3300000>;
118 regulator-max-microvolt = <3300000>;
119 regulator-always-on;
123 regulator-name = "FUSE_2V5";
124 regulator-min-microvolt = <2500000>;
125 regulator-max-microvolt = <2500000>;
129 regulator-name = "VDDANA";
130 regulator-min-microvolt = <3300000>;
131 regulator-max-microvolt = <3300000>;
132 regulator-always-on;
139 phy-mode = "rgmii";
140 #address-cells = <1>;
141 #size-cells = <0>;
144 ethernet-phy@7 {
150 pinctrl-names = "default";
151 pinctrl-0 = <&pinctrl_pwm0_pwmh0_0 &pinctrl_pwm0_pwmh1_0>;
155 usart0: serial@f001c000 {
159 usart1: serial@f0020000 {
160 pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
164 uart0: serial@f0024000 {
169 pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
173 bus-width = <4>;
174 cd-gpios = <&pioE 1 GPIO_ACTIVE_HIGH>;
179 cs-gpios = <&pioC 25 0>;
184 pinctrl-0 = <
202 pinctrl-0 = <&pinctrl_i2c2_pu>;
207 phy-mode = "rmii";
208 #address-cells = <1>;
209 #size-cells = <0>;
212 ethernet-phy@1 {
217 dbgu: serial@ffffee00 {
218 u-boot,dm-pre-reloc;
224 u-boot,dm-pre-reloc;
226 atmel,pins =
232 atmel,pins =
238 atmel,pins =
243 u-boot,dm-pre-reloc;
244 atmel,pins =
249 u-boot,dm-pre-reloc;
250 atmel,pins =
255 atmel,pins =
260 atmel,pins =
268 nand-bus-width = <8>;
269 nand-ecc-mode = "hw";
270 atmel,has-pmecc;
271 atmel,pmecc-cap = <4>;
272 atmel,pmecc-sector-size = <512>;
273 nand-on-flash-bbt;
308 atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>; /* PE9, conflicts with A9 */
309 pinctrl-names = "default";
310 pinctrl-0 = <&pinctrl_usba_vbus>;
315 num-ports = <3>;
316 atmel,vbus-gpio = <0
329 compatible = "regulator-fixed";
331 regulator-name = "mmc0-card-supply";
332 regulator-min-microvolt = <3300000>;
333 regulator-max-microvolt = <3300000>;
334 regulator-always-on;
338 compatible = "gpio-keys";
340 pinctrl-names = "default";
341 pinctrl-0 = <&pinctrl_key_gpio>;
347 wakeup-source;
352 compatible = "gpio-leds";
357 linux,default-trigger = "heartbeat";