arm/dts/armada-xp-synology-ds414.dts

13  * The 0xf1000000 is the default used by the recent, DT-capable, U-Boot
16  * were delivered with an older version of u-boot that left internal
21  * installing it from u-boot prompt) or adjust the Devive Tree
25 /dts-v1/;
27 #include <dt-bindings/input/input.h>
28 #include <dt-bindings/gpio/gpio.h>
29 #include "armada-xp-mv78230.dtsi"
33 	compatible = "synology,ds414", "marvell,armadaxp-mv78230",
34 		     "marvell,armadaxp", "marvell,armada-370-xp";
38 		stdout-path = &uart0;
54 		pcie-controller {
58 			 * Connected to Marvell 88SX7042 SATA-II controller
76 		internal-regs {
78 			/* RTC is provided by Seiko S-35390A below */
85 				u-boot,dm-pre-reloc;
87 				spi-flash@0 {
88 					u-boot,dm-pre-reloc;
89 					#address-cells = <1>;
90 					#size-cells = <1>;
93 					spi-max-frequency = <20000000>;
98 					 * Synology u-boot uses its compiled-in environment
99 					 * and it seems Synology did not care to change u-boot
102 					 * if you do a 'saveenv' under u-boot, your modified
109 					partition@00000000 { /* u-boot */
124 					partition@007d0000 { /* MAC address and serial number */
142 				clock-frequency = <400000>;
155 			 * USB-serial converter connected when the power
161 			serial@12000 {
163 				u-boot,dm-pre-reloc;
167 			serial@12100 {
172 				compatible = "synology,power-off";
183 				phy0: ethernet-phy@0 { /* Marvell 88E1512 */
187 				phy1: ethernet-phy@1 { /* Marvell 88E1512 */
194 				pinctrl-0 = <&ge0_rgmii_pins>;
195 				pinctrl-names = "default";
197 				phy-mode = "rgmii-id";
201 				pinctrl-0 = <&ge1_rgmii_pins>;
202 				pinctrl-names = "default";
205 				phy-mode = "rgmii-id";
211 		compatible = "simple-bus";
212 		#address-cells = <1>;
213 		#size-cells = <0>;
214 		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
216 		pinctrl-names = "default";
218 		sata1_regulator: sata1-regulator {
219 			compatible = "regulator-fixed";
221 			regulator-name = "SATA1 Power";
222 			regulator-min-microvolt = <5000000>;
223 			regulator-max-microvolt = <5000000>;
224 			startup-delay-us = <2000000>;
225 			enable-active-high;
226 			regulator-always-on;
227 			regulator-boot-on;
231 		sata2_regulator: sata2-regulator {
232 			compatible = "regulator-fixed";
234 			regulator-name = "SATA2 Power";
235 			regulator-min-microvolt = <5000000>;
236 			regulator-max-microvolt = <5000000>;
237 			startup-delay-us = <4000000>;
238 			enable-active-high;
239 			regulator-always-on;
240 			regulator-boot-on;
244 		sata3_regulator: sata3-regulator {
245 			compatible = "regulator-fixed";
247 			regulator-name = "SATA3 Power";
248 			regulator-min-microvolt = <5000000>;
249 			regulator-max-microvolt = <5000000>;
250 			startup-delay-us = <6000000>;
251 			enable-active-high;
252 			regulator-always-on;
253 			regulator-boot-on;
257 		sata4_regulator: sata4-regulator {
258 			compatible = "regulator-fixed";
260 			regulator-name = "SATA4 Power";
261 			regulator-min-microvolt = <5000000>;
262 			regulator-max-microvolt = <5000000>;
263 			startup-delay-us = <8000000>;
264 			enable-active-high;
265 			regulator-always-on;
266 			regulator-boot-on;
273 	sata1_pwr_pin: sata1-pwr-pin {
274 		marvell,pins = "mpp42";
278 	sata2_pwr_pin: sata2-pwr-pin {
279 		marvell,pins = "mpp44";
283 	sata3_pwr_pin: sata3-pwr-pin {
284 		marvell,pins = "mpp45";
288 	sata4_pwr_pin: sata4-pwr-pin {
289 		marvell,pins = "mpp46";
293 	sata1_pres_pin: sata1-pres-pin {
294 		marvell,pins = "mpp34";
298 	sata2_pres_pin: sata2-pres-pin {
299 		marvell,pins = "mpp35";
303 	sata3_pres_pin: sata3-pres-pin {
304 		marvell,pins = "mpp40";
308 	sata4_pres_pin: sata4-pres-pin {
309 		marvell,pins = "mpp41";
313 	syno_id_bit0_pin: syno-id-bit0-pin {
314 		marvell,pins = "mpp26";
318 	syno_id_bit1_pin: syno-id-bit1-pin {
319 		marvell,pins = "mpp28";
323 	syno_id_bit2_pin: syno-id-bit2-pin {
324 		marvell,pins = "mpp29";
328 	fan1_alarm_pin: fan1-alarm-pin {
329 		marvell,pins = "mpp33";
333 	fan2_alarm_pin: fan2-alarm-pin {
334 		marvell,pins = "mpp32";