arm/dts/armada-8040-db.dts

4  * This file is dual-licensed: you can use it either under the terms
47 #include "armada-8040.dtsi"
51 	compatible = "marvell,armada8040-db", "marvell,armada8040",
52 		     "marvell,armada-ap806-quad", "marvell,armada-ap806";
55 		stdout-path = "serial0:115200n8";
69 /* Accessible over the mini-USB CON9 connector on the main board */
76 	 * SDIO  [0-10]
80 	pin-func = < 1 1 1 1 1 1 1 1 1 1
85 	pinctrl-names = "default";
86 	pinctrl-0 = <&ap_emmc_pins>;
87 	bus-width = <8>;
93 	 *	[0-31]	= 0xff: Keep default CP0_shared_pins
102 	 *	[37-38]	I2C0
104 	 *	[40-41]	SATA[0/1]_PRESENT_ACTIVEn
105 	 *	[42-43]	XG_MDC/XG_MDIO (XSMI)
106 	 *	[44-55]	RGMII1
107 	 *	[56-62]	SD
110 	pin-func = < 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
126 	 *	Lane 5: PCIe2 (x1)
129 		phy-type = <PHY_TYPE_PEX0>;
132 		phy-type = <PHY_TYPE_SATA0>;
135 		phy-type = <PHY_TYPE_SFI>;
138 		phy-type = <PHY_TYPE_SATA1>;
141 		phy-type = <PHY_TYPE_USB3_HOST1>;
144 		phy-type = <PHY_TYPE_PEX2>;
163 	pinctrl-names = "default";
164 	pinctrl-0 = <&cpm_i2c0_pins>;
166 	clock-frequency = <100000>;
193 	pinctrl-names = "default";
194 	pinctrl-0 = <&cpm_sdhci_pins>;
195 	bus-width = <4>;
201 	 *	[0-11]	RGMII0
202 	 *	[13-16]	SPI1
205 	 *	[29-30]	UART0
206 	 *	[32-62]	= 0xff: Keep default CP1_shared_pins
209 	pin-func = < 0x3  0x3  0x3  0x3  0x3  0x3  0x3  0x3  0x3  0x3
225 	 *	Lane 5: PCIe2 (x1)
228 		phy-type = <PHY_TYPE_PEX0>;
231 		phy-type = <PHY_TYPE_SATA0>;
234 		phy-type = <PHY_TYPE_SFI>;
237 		phy-type = <PHY_TYPE_SATA1>;
240 		phy-type = <PHY_TYPE_PEX1>;
243 		phy-type = <PHY_TYPE_PEX2>;
262 	pinctrl-names = "default";
263 	pinctrl-0 = <&cps_spi1_pins>;
266 	spi-flash@0 {
267 		#address-cells = <1>;
268 		#size-cells = <1>;
269 		compatible = "jedec,spi-nor";
271 		spi-max-frequency = <10000000>;
274 			compatible = "fixed-partitions";
275 			#address-cells = <1>;
276 			#size-cells = <1>;
279 				label = "U-Boot";
310 	phy1: ethernet-phy@1 {
321 	phy = <&phy1>;
322 	phy-mode = "rgmii-id";