arm/dts/am335x-brppt1-spi.dts

1 // SPDX-License-Identifier: GPL-2.0+
4  * http://www.br-automation.com
7 /dts-v1/;
15 	fset: factory-settings {
16 		bl-version	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
18 		order-no	= "6PPT30 (SPI)";
19 		hw-revision	= "ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456890";
20 		serial-no	= "0";
21 		device-id	= <0x0>;
22 		parent-id	= <0x0>;
23 		hw-variant	= <0x1>;
39 		stdout-path = &uart0;
51 		enable-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
54 		bkl-pwm = <&pwmbacklight>;
55 		bkl-tps = <&tps_bl>;
57 		panel-info {
58 			ac-bias		= <255>;
59 			ac-bias-intrpt	= <0>;
60 			dma-burst-sz	= <16>;
63 			sync-edge	= <0>;
64 			sync-ctrl	= <1>;
65 			raster-order	= <0>;
66 			fifo-th		= <0>;
69 		display-timings {
70 			native-mode = <&timing0>;
72 				clock-frequency	= <32000000>;
75 				hfront-porch	= <2>;
76 				hback-porch	= <192>;
77 				hsync-len	= <1>;
78 				vfront-porch	= <20>;
79 				vback-porch	= <2>;
80 				vsync-len	= <1>;
81 				hsync-active	= <1>;
82 				vsync-active	= <1>;
90 		compatible = "regulator-fixed";
91 		regulator-name = "vmmcsd_fixed";
92 		regulator-min-microvolt = <3300000>;
93 		regulator-max-microvolt = <3300000>;
96 	pwm0: omap-pwm@timer5 {
97 		compatible = "ti,omap-dmtimer-pwm";
99 		#pwm-cells = <3>;
102 	pwm1: omap-pwm@timer6 {
103 		compatible = "ti,omap-dmtimer-pwm";
105 		#pwm-cells = <3>;
108 	beeper: pwm-beep {
109 		compatible = "pwm-beeper";
113 	pwmbacklight: pwm-bkl {
114 		compatible = "pwm-backlight";
117 		default-brightness-level = <255>;
118 		brightness-levels = <0 16 32 64 128 170 202 234 255>;
120 		power-supply = <&vmmcsd_fixed>;
121 		enable-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
126 	u-boot,dm-spl;
135 	u-boot,dm-spl;
137 	clock-frequency = <400000>;
140 		u-boot,dm-spl;
145 			compatible = "ti,tps65217-bl";
146 			isel = <1>;	/* 1 - ISET1, 2 ISET2 */
148 			default-brightness = <50>;
155 	clock-frequency = <100000>;
159 	u-boot,dm-spl;
162 	cs-gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>,
167 	spi-max-frequency = <24000000>;
170 		u-boot,dm-spl;
171 		u-boot,dm-pre-reloc;
172 		compatible = "spidev", "spi-flash";
173 		spi-max-frequency = <24000000>;
215 	phy0: ethernet-phy@0 {
219 	phy1: ethernet-phy@1 {
229 	phy-handle = <&phy0>;
231 	phy-mode = "mii";
235 	phy-handle = <&phy1>;
237 	phy-mode = "mii";
241 	u-boot,dm-spl;
242 	vmmc-supply = <&vmmcsd_fixed>;
243 	bus-width = <0x4>;
244 	ti,non-removable;
245 	ti,needs-special-hs-handling;
246 	ti,vcc-aux-disable-is-sleep;
251 	u-boot,dm-spl;
252 	vmmc-supply = <&vmmcsd_fixed>;
253 	bus-width = <0x8>;
254 	ti,non-removable;
255 	ti,needs-special-hs-handling;
256 	ti,vcc-aux-disable-is-sleep;
277 	u-boot,dm-spl;
278 	ti,no-reset-on-init;
282 	u-boot,dm-spl;
283 	ti,no-reset-on-init;
287 	u-boot,dm-spl;
288 	ti,no-reset-on-init;
292 	u-boot,dm-spl;
293 	ti,no-reset-on-init;
297 	ti,no-reset-on-init;
298 	ti,no-idle-on-init;
305 		ti,x-plate-resistance = <200>;
306 		ti,zx-cutoff-ratio = <40>;
309 		ti,coordinate-readouts = <5>;
310 		ti,wire-config = <0x00 0x11 0x22 0x33>;
312 		bnr-buttons {
313 			Home-Button {};
317 	adc {
318 		ti,adc-channels = <5 6 7>;
324 	ti,no-reset-on-init;
325 	ti,no-idle-on-init;
330 	ti,no-reset-on-init;
331 	ti,no-idle-on-init;
336 	ti,no-reset-on-init;
337 	ti,no-idle-on-init;