phosphor-power-sequencer/docs/chassis_status.md

6 status. The `phosphor-power-sequencer` application publishes one of those
8 used as input by `phosphor-power-sequencer.`
12 The `state` and `pgood` properties exist on the `org.openbmc.control.Power`
15 `state` has a value of 0 or 1. `state` represents the desired power state for
19 `pgood` has a value of 0 or 1. `pgood` represents the power good (pgood) state
20 of the chassis. 0 means off, and 1 means on. This is the actual, current power
21 state. This property is set based on the chassis power good signal from the
22 power sequencer device.
24 `phosphor-power-sequencer` publishes the `org.openbmc.control.Power` interface
61 power on some chassis, such as if they are missing or have no input power. See
69 If a power good fault occurs in a chassis after the system powered on, the
72 Eventually the system will be powered off due to the power good fault. See
73 [Power Good Faults](pgood_faults.md) for more information.
84 When `phosphor-power-sequencer` is started, it needs to set initial values for
86 input power or after the BMC is reset.
88 The chassis power good signal is read from the power sequencer device. Both the
89 `state` and `pgood` properties are set to the value of the power good signal.
90 For example, if the chassis power good is true, both `state` and `pgood` are set
91 to the value 1. Thus, `phosphor-power-sequencer` assumes the chassis `state`
94 In a multiple chassis system, it might not be possible to read the chassis power
96 input power. See the sections below for information about how the `pgood`
105 `phosphor-power-sequencer` does not publish this interface, but it checks the
112 - The chassis power good signal from the power sequencer will **not** be read.
114   `org.openbmc.control.Power` interface for the chassis will be set to 0.
116   The `state` property on the `org.openbmc.control.Power` interface for the
125 `phosphor-power-sequencer` does not publish this interface, but it checks the
130 the chassis does not have any input power ([blackout](power_loss.md)) or
135 - The chassis power good signal from the power sequencer will **not** be read.
136   Since communication to the chassis is not possible, the value of the power
138   - If the chassis is experiencing a blackout, the chassis has no input power
145   The `state` property on the `org.openbmc.control.Power` interface for the
154 `phosphor-power-sequencer` does not publish this interface, but it checks the
164 - The chassis power good signal from the power sequencer will be read. The
165   `pgood` property on the `org.openbmc.control.Power` interface for the chassis
168   The `state` property on the `org.openbmc.control.Power` interface for the
176 `phosphor-power-sequencer` does not publish this interface, but it checks the
181 [power loss](power_loss.md) is occurring, such as a power company utility
182 failure or an unplugged power cord. See the sub-sections below for more
185 ### Chassis power status
187 The `phosphor-chassis-power` application publishes the
191 - `/xyz/openbmc_project/power/chassis/chassis1`
192 - `/xyz/openbmc_project/power/chassis/chassis2`
194 - `/xyz/openbmc_project/power/chassis/chassisN`
199 - The chassis power good signal from the power sequencer will **not** be read.
200   Since the chassis has no input power, the `pgood` property on the
201   `org.openbmc.control.Power` interface for the chassis will be set to 0.
203   The `state` property on the `org.openbmc.control.Power` interface for the
205   chassis was not powered on due to an input power problem.
207 ### Power supplies power status
209 The `phosphor-power-supply` application publishes the
213 - `/xyz/openbmc_project/power/power_supplies/chassis1/psus`
214 - `/xyz/openbmc_project/power/power_supplies/chassis2/psus`
216 - `/xyz/openbmc_project/power/power_supplies/chassisN/psus`
221 - The chassis power good signal from the power sequencer will be read. The
222   `pgood` property on the `org.openbmc.control.Power` interface for the chassis
225   The `state` property on the `org.openbmc.control.Power` interface for the
227   chassis was not powered on due to an input power problem.