Lines Matching +full:led +full:- +full:order
1 # SPDX-License-Identifier: GPL-2.0-only
45 tristate "Active-semi ACT8945A"
50 Support for the ACT8945A PMIC from Active-semi. This device
51 features three step-down DC/DC converters and four low-dropout
67 sun4i-gpadc-iio and the hwmon driver iio_hwmon.
70 called sun4i-gpadc.
101 tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
123 additional drivers must be enabled in order to use the
132 over at91-usart-serial driver and usart-spi-driver. Only one function
148 tristate "Atmel HLCDC (High-end LCD Controller)"
155 additional drivers must be enabled in order to use the
185 tristate "X-Powers AC100"
189 If you say Y here you get support for the X-Powers AC100 audio codec
200 tristate "X-Powers AXP series PMICs with I2C"
205 If you say Y here you get support for the X-Powers AXP series power
217 tristate "X-Powers AXP series PMICs with RSB"
221 If you say Y here you get support for the X-Powers AXP series power
234 sub-devices. This driver will instantiate additional drivers such
238 called cros-ec-dev.
344 usually found on PXA processors-based platforms. This includes
347 LEDs and battery-charger under the corresponding menus.
363 order to use the functionality of the device.
375 order to use the functionality of the device.
387 Additional drivers must be enabled in order to use the functionality
400 Additional drivers must be enabled in order to use the functionality
412 Additional drivers must be enabled in order to use the functionality
416 tristate "Dialog Semiconductor DA9150 Charger Fuel-Gauge chip"
422 This adds support for the DA9150 integrated charger and fuel-gauge
424 Additional drivers must be enabled in order to use the specific
432 This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter
433 DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2,
434 etc. must be enabled in order to use the functionality of
443 This adds support for the power-off functionality and access to
445 Embedded Controller. To use the LED functionality LEDS_ARIEL must
468 such as push-button monitor, multiple ADC's for voltage and
471 Additional drivers must be enabled in order to use the
482 additional drivers must be enabled in order to use the
518 Analog-to-Digital Converter (LRADC) found on the i.MX23 and i.MX28
520 device, additional drivers must be enabled in order to use the
522 mxs-lradc-adc for ADC readings
523 mxs-lradc-ts for touchscreen support
526 called mxs-lradc.
543 Add support for HiSilicon Hi6421 PMIC. Hi6421 includes multi-
547 menus in order to enable them.
548 We communicate with the Hi6421 via memory-mapped I/O.
558 multi-functions, such as regulators, RTC, codec, Coulomb counter,
563 menus in order to enable them.
586 The GPIO exports a total amount of 8 interrupt-capable GPIOs.
623 causes the designware-i2c driver to be builtin for the same reason.
650 causes the designware-i2c driver to be builtin for the same reason.
667 needs the designware-i2c driver to be builtin for the same reason.
691 I2C, SPI and HS-UART starting from Intel Sunrisepoint (Intel Skylake
700 I2C, SPI and HS-UART starting from Intel Sunrisepoint (Intel Skylake
713 multi-function device that exposes IPC, General Control
714 Register and P-unit access. In addition this creates devices
734 IQS621, IQS622, IQS624 and IQS625 multi-function sensors. Additional
735 options must be selected to enable device-specific functions.
741 tristate "Janz CMOD-IO PCI MODULbus Carrier Board"
745 This is the core driver for the Janz CMOD-IO PCI MODULbus
760 will be called kempld-core.
772 battery-charger under the corresponding menus.
795 battery-charger under the corresponding menus.
806 MAX77836 Micro-USB ICs with battery charger.
808 additional drivers must be enabled in order to use the functionality
821 must be enabled in order to use the functionality of the device.
837 must be enabled in order to use the functionality of the device.
850 'max77650'. Additional drivers can be enabled in order to use
852 charger, LED, onkey.
866 additional drivers must be enabled in order to use the functionality
880 additional drivers must be enabled in order to use the functionality
892 low-dropout regulators, 8 GPIOs, RTC, watchdog etc. This driver
894 drivers must be enabled in order to use each functionality of the
908 additional drivers must be enabled in order to use the functionality
920 accessing the device; additional drivers must be enabled in order
930 accessing the device, additional drivers must be enabled in order
943 additional drivers must be enabled in order to use the functionality
955 additional drivers must be enabled in order to use the functionality
967 PMU part includes Charger, Flashlight, RGB LED
968 PMIC part includes 2-channel BUCKs and 2-channel LDOs
969 LDO part includes 4-channel LDOs
981 voltage supply, one general purpose LDO, and the USB Type-C & PD
982 controller complies with the latest USB Type-C and PD standards.
994 accessing the device; additional drivers must be enabled in order
1004 The device supports multiple sub-devices like LED, HWMON and WDT.
1006 additional drivers must be enabled in order to use the
1029 called ocelot-soc.
1074 certain e-book readers designed by the original design manufacturer
1078 tristate "Nokia Retu and Tahvo multi-function device"
1083 Retu and Tahvo are a multi-function devices found on Nokia
1094 so that function-specific drivers can bind to them.
1118 built-in PM8xxx PMIC chips.
1124 module. This will build a module called "pm8xxx-core".
1153 series as a module. The module will be called "qcom-spmi-pmic".
1162 To enable support for building sub-devices as modules,
1166 tristate "RDC R-321x southbridge"
1170 Say yes here if you want to have support for the RDC R-321x SoC
1194 sub-devices like charger, fuel gauge, flash LED, current source,
1218 through i2c interface. The device supports multiple sub-devices
1220 Additional drivers must be enabled in order to use the
1238 through I2C interface. The device supports multiple sub-devices
1252 through an SPI interface. The device supports multiple sub-devices
1253 including interrupts, LDO & DCDC regulators, and power on-key.
1266 additional drivers must be enabled in order to use the
1280 additional drivers must be enabled in order to use the functionality
1284 module will be called sec-core.
1296 radio. This MFD driver connects the radio-si476x V4L2 module
1300 module will be called si476x-core.
1309 to be shared by all sub-devices.
1312 sub-devices represented by child nodes in Device Tree will be
1325 * SMARC-sAL28
1380 the Multi-Function Timer Pulse Unit 3 (MTU3a) hardware available
1386 bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
1397 bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
1410 bool "ST-Ericsson DB8500 Power Reset Control Management Unit"
1437 additional drivers must be enabled in order to use the functionality
1440 GPIO: stmpe-gpio
1441 Keypad: stmpe-keypad
1442 Touchscreen: stmpe-ts
1443 ADC: stmpe-adc
1504 With these functionalities, it can be used for LED string control or
1525 LM36274. It consists of backlight, LED and regulator driver.
1557 high-power "white LED driver". This boost converter is
1597 additional drivers must be enabled in order to use the
1613 additional drivers must be enabled in order to use the
1617 tristate "TI TPS65217 Power Management / White LED chips"
1624 Power Management / White LED chips.
1698 additional drivers must be enabled in order to use the
1757 will be called tps6594-i2c.
1770 will be called tps6594-spi.
1781 so that function-specific drivers can bind to them.
1783 These multi-function chips are found on many OMAP2 and OMAP3
1797 This driver uses board-specific data to initialize the resources
1818 additional drivers must be enabled in order to use the
1827 regulators, Dual slot memory card transceivers, real-time clock
1838 driver connects the radio-wl1273 V4L2 module and the wl1273
1851 additional drivers must be enabled in order to use the LED,
1852 backlight or ambient-light-sensor functionality of the device.
1863 for in-vehicle infontainment, called Russellville.
1874 additional drivers must be enabled in order to use the
1878 tristate "TQ-Systems IO controller TQMX86"
1882 TQ-Systems IO controller and watchdog device, found on their
1965 the device, additional drivers must be enabled in order to use
1982 order to use the functionality of the device.
1995 order to use the functionality of the device.
2019 The WM8994 is a highly integrated hi-fi CODEC designed for
2023 core support for the WM8994, in order to use the actual
2033 The WM9705, WM9712 and WM9713 is a highly integrated hi-fi CODEC
2037 support for the WM97xx, in order to use the actual functionality of
2047 in various ST Microelectronics and ST-Ericsson embedded
2072 Power Management ICs. BD71828GW and BD71815AGW are single-chip power
2073 management ICs mainly for battery-powered portable devices.
2076 also a single-cell linear charger, a Coulomb counter, a real-time
2089 designed to be used to power R-Car series processors.
2092 tristate "Support for STM32 Low-Power Timer"
2098 Select this option to enable STM32 Low-Power Timer driver
2103 module will be called stm32-lptimer.
2126 STPMIC1. In order to use the actual functionality of the device other
2133 tristate "Support for STMicroelectronics Multi-Function eXpander (STMFX)"
2139 Support for the STMicroelectronics Multi-Function eXpander.
2142 additional drivers must be enabled in order to use the functionality
2173 in order to use the functionality of the device.
2189 power-on options, power-off control and system FAN control on recent
2193 additional drivers must be enabled in order to use the functionality
2219 order to use the functionality of the device.
2269 This option enables basic support for the SGI IOC3-based
2293 additional drivers must be enabled in order to use the functionality
2305 additional drivers must be enabled in order to use the functionality
2319 Additional drivers must be enabled in order to use the functionality
2333 Additional drivers must be enabled in order to use the functionality