Lines Matching +full:logicvc +full:- +full:3
1 # SPDX-License-Identifier: GPL-2.0-only
47 this symbol, but new drivers should use the generic gpio-regmap
57 non-sleeping contexts. They can make bitbanged serial protocols
118 Enables support for the idio-16 library functions. The idio-16 library
120 ACCES IDIO-16 family such as the 104-IDIO-16 and the PCI-IDIO-16.
122 If built as a module its name will be gpio-idio-16.
128 tristate "GPIO driver for 74xx-ICs with MMIO access"
132 Say yes here to support GPIO functionality for 74xx-compatible ICs
149 If driver is built as a module it will be called gpio-altera.
185 tristate "Raspberry Pi 3 GPIO Expander"
192 Turn on GPIO support for the expander on Raspberry Pi 3 boards, using
310 tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
313 Say yes here to support basic platform_device memory-mapped GPIO controllers.
332 This GPIO controller supports double-edge interrupt and multi-core
351 ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8
375 tristate "Xylon LogiCVC GPIO support"
378 Say yes here to support GPIO functionality of the Xylon LogiCVC
382 bool "Loongson-2/3 GPIO support"
385 Driver for GPIO functionality on Loongson-2F/3A/3B processors.
434 created by attaching a 16-bit latch to the bus.
493 Say yes here to support the on-chip GPIO lines on the OCTEON
520 tristate "Renesas R-Car and RZ/G GPIO support"
524 Say yes here to support GPIO on Renesas R-Car or RZ/G SoCs.
544 are grouped in four 8-bit wide ports.
551 A 32-bit single register GPIO fixed in/out implementation. This
574 maintain their value during backup/self-refresh.
592 via a SIOX bus and have a number of fixed-direction I/O lines.
600 This is a single-register MMIO GPIO driver for complex cases
642 - Elkhart Lake
643 - Merrifield
645 If built as a module its name will be gpio-tangier.
674 tristate "TS-4800 DIO blocks and compatibles"
679 This driver support TS-4800 FPGA GPIO controllers.
682 tristate "Cavium ThunderX/OCTEON-TX GPIO"
689 Say yes here to support the on-chip GPIO lines on the ThunderX
690 and OCTEON-TX families of SoCs.
726 bool "APM X-Gene GPIO controller support"
729 This driver is to support the GPIO block within the APM X-Gene SoC
735 tristate "APM X-Gene GPIO standby controller support"
741 This driver supports the GPIO block within the APM X-Gene
784 tristate "ZynqMP ps-mode pin GPIO configuration driver"
788 Say yes here to support the ZynqMP ps-mode pin GPIO configuration
791 This ps-mode pin GPIO driver is based on GPIO framework. PS_MODE
792 is 4-bits boot mode pins. It sets and gets the status of
793 the ps-mode pin. Every pin can be configured as input/output.
803 tristate "GPIO support for AMD Fusion Controller Hub (G-series SOCs)"
806 as found on G-series SOCs (e.g. GX-412TC).
809 needs to be provided with platform-specific configuration.
820 ARMv7-based SoCs.
829 IDT 79RC3243X-based devices like Mikrotik RB532.
832 be called gpio-idt3243x.
836 menu "Port-mapped I/O GPIO drivers"
862 If built as a module its name will be gpio-i8255.
865 tristate "ACCES 104-DIO-48E GPIO support"
874 Enables GPIO support for the ACCES 104-DIO-48E series (104-DIO-48E,
875 104-DIO-24E). The base port addresses for the devices may be
880 tristate "ACCES 104-IDIO-16 GPIO support"
886 Enables GPIO support for the ACCES 104-IDIO-16 family (104-IDIO-16,
887 104-IDIO-16E, 104-IDO-16, 104-IDIO-8, 104-IDIO-8E, 104-IDO-8). The
893 tristate "ACCES 104-IDI-48 GPIO support"
901 Enables GPIO support for the ACCES 104-IDI-48 family (104-IDI-48A,
902 104-IDI-48AC, 104-IDI-48B, 104-IDI-48BC). The base port addresses for
908 tristate "Fintek and Nuvoton Super-I/O GPIO support"
910 This option enables support for GPIOs found on Fintek Super-I/O
912 As well as Nuvoton Super-I/O chip NCT6126D.
915 be called f7188x-gpio.
918 tristate "Diamond Systems GPIO-MM GPIO support"
924 Enables GPIO support for the Diamond Systems GPIO-MM and GPIO-MM-12.
926 The Diamond Systems GPIO-MM device features 48 lines of digital I/O
959 active during S3. The suspend-powered GPIOs can be used to wake the
960 system from the Suspend-to-RAM state.
966 Twenty-one are powered by the core power rail and 9 from the
979 be called gpio-sch311x.
982 tristate "TS-5500 DIO blocks and compatibles"
986 Technologic Systems platforms. It includes, but is not limited to, 3
987 blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
1000 boot-time parameter "gpio_winbond.gpios" with a bitmask of GPIO
1004 be called gpio-winbond.
1025 tristate "Avionic Design N-bit GPIO expander"
1044 be called gpio-fxl6408.
1051 GPIO driver for ADI DS4520 I2C-based GPIO expander.
1055 be called gpio-ds4520.
1062 Expander. This is used at least on the Cambria GW2358-4.
1068 GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
1071 tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
1073 Say yes here to support the MAX7319, MAX7320-7327 series of I2C
1075 Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
1100 Say yes here to provide access to several register-oriented
1125 tristate "PCA9570 4-Bit I2C GPO expander"
1130 be called gpio-pca9570.
1137 Say yes here to provide access to most "quasi-bidirectional" I2C
1154 This driver provides an in-kernel interface to those GPIOs using
1155 platform-neutral GPIO calls.
1158 tristate "TPIC2810 8-Bit I2C GPO expander"
1163 be called gpio-tpic2810.
1171 Series supported include TS-4100, TS-4900, TS-7970 and TS-7990.
1181 This option enables support for on-chip GPIO found
1206 will be called gpio-bd71815.
1218 will be called gpio-bd71828.
1229 will be called gpio-bd9571mwv.
1238 Say Yes if you have a Intel SoC-based tablet with Crystal Cove PMIC
1242 called gpio-crystalcove.
1267 The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
1270 If driver is built as a module it will be called gpio-da9055.
1282 will be called gpio-dln2.
1301 be called gpio-elkhartlake.
1304 tristate "Janz VMOD-TTL Digital IO Module"
1307 This enables support for the Janz VMOD-TTL Digital IO module.
1319 called gpio-kempld.
1331 will be called gpio-ljca.
1349 called gpio-lp873x.
1355 This driver supports the GPIO on TI Lp873565 PMICs. 3 GPIOs are present
1359 called gpio-lp87565.
1418 called gpio-sl28cpld.
1451 they are input-only or output-only type.
1454 module will be called gpio-tn48m.
1511 There are 7 GPIOs and few sensor-related GPIOs supported
1517 tristate "TQ-Systems TQMx86 GPIO"
1528 Say yes here to access the GPIO signals of various multi-function
1545 Say Yes if you have an Intel SoC-based tablet with Whiskey Cove PMIC
1549 called gpio-wcove.
1597 This chip can be found on Miro, Hauppauge and STB TV-cards.
1602 Documentation/driver-api/gpio/bt8xxgpio.rst
1629 tristate "Mellanox BlueField 3 SoC GPIO"
1634 Say Y if you want GPIO support on Mellanox BlueField 3 SoC.
1637 This controller should be used in parallel with pinctrl-mlxbf3 to
1639 This driver can also be built as a module called mlxbf3-gpio.
1648 Hub) which is for IVI (In-Vehicle Infotainment) use.
1668 tristate "ACCES PCI-IDIO-16 GPIO support"
1672 Enables GPIO support for the ACCES PCI-IDIO-16. An interrupt is
1678 tristate "ACCES PCIe-IDIO-24 GPIO support"
1684 Enables GPIO support for the ACCES PCIe-IDIO-24 family (PCIe-IDIO-24,
1685 PCIe-IDI-24, PCIe-IDO-24, PCIe-IDIO-12). An interrupt is generated
1691 tristate "RDC R-321x GPIO support"
1712 tristate "74x164 serial-in/parallel-out 8-bits shift register"
1715 Driver for 74x164 compatible serial-in/parallel-out 8-outputs
1724 MAX31953 and MAX31963 industrial serializer, a daisy-chainable
1733 GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
1736 tristate "Freescale MC33880 high-side/low-side switch"
1738 SPI driver for Freescale MC33880 high-side/low-side switch.
1742 tristate "Generic parallel-in/serial-out shift register"
1744 GPIO driver for SPI compatible parallel-in/serial-out shift
1748 tristate "EXAR XRA1403 16-bit GPIO expander"
1751 GPIO driver for EXAR XRA1403 16-bit SPI-based GPIO expander.
1788 - Assign permissions for a collection of GPIO lines to a user,
1789 - Export a collection of GPIO lines to a virtual machine,
1790 - Provide a generic driver for a GPIO-operated device in an
1807 tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
1815 Say Y here to enable guest support for virtio-based GPIO controllers.
1825 This enables the GPIO simulator - a configfs-based GPIO testing