dts/renesas/r8a77970-eagle.dts

1 // SPDX-License-Identifier: GPL-2.0
3  * Device Tree Source for the Eagle board with R-Car V3M
5  * Copyright (C) 2016-2017 Renesas Electronics Corp.
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
29 		stdout-path = "serial0:115200n8";
32 	d3p3: regulator-fixed {
33 		compatible = "regulator-fixed";
34 		regulator-name = "fixed-3.3V";
35 		regulator-min-microvolt = <3300000>;
36 		regulator-max-microvolt = <3300000>;
37 		regulator-boot-on;
38 		regulator-always-on;
41 	hdmi-out {
42 		compatible = "hdmi-connector";
47 				remote-endpoint = <&adv7511_out>;
52 	lvds-decoder {
55 		vcc-supply = <&d3p3>;
58 			#address-cells = <1>;
59 			#size-cells = <0>;
64 					remote-endpoint = <&lvds0_out>;
71 					remote-endpoint = <&adv7511_in>;
83 	x1_clk: x1-clock {
84 		compatible = "fixed-clock";
85 		#clock-cells = <0>;
86 		clock-frequency = <148500000>;
91 	pinctrl-0 = <&avb_pins>;
92 	pinctrl-names = "default";
94 	renesas,no-ether-link;
95 	phy-handle = <&phy0>;
96 	rx-internal-delay-ps = <1800>;
97 	tx-internal-delay-ps = <2000>;
100 	phy0: ethernet-phy@0 {
101 		compatible = "ethernet-phy-id0022.1622",
102 			     "ethernet-phy-ieee802.3-c22";
103 		rxc-skew-ps = <1500>;
105 		interrupt-parent = <&gpio1>;
107 		reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
112 	pinctrl-0 = <&canfd0_pins>;
113 	pinctrl-names = "default";
127 				clock-lanes = <0>;
128 				data-lanes = <1 2 3 4>;
129 				remote-endpoint = <&max9286_out0>;
137 	clock-names = "du.0", "dclkin.0";
142 	clock-frequency = <16666666>;
146 	clock-frequency = <32768>;
150 	pinctrl-0 = <&i2c0_pins>;
151 	pinctrl-names = "default";
154 	clock-frequency = <400000>;
159 		gpio-controller;
160 		#gpio-cells = <2>;
166 		interrupt-parent = <&gpio1>;
169 		adi,input-depth = <8>;
170 		adi,input-colorspace = "rgb";
171 		adi,input-clock = "1x";
174 			#address-cells = <1>;
175 			#size-cells = <0>;
180 					remote-endpoint = <&thc63lvd1024_out>;
187 					remote-endpoint = <&hdmi_con_out>;
195 	pinctrl-0 = <&i2c3_pins>;
196 	pinctrl-names = "default";
199 	clock-frequency = <400000>;
201 	gmsl0: gmsl-deserializer@48 {
205 		maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
206 		enable-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
209 			#address-cells = <1>;
210 			#size-cells = <0>;
231 					clock-lanes = <0>;
232 					data-lanes = <1 2 3 4>;
233 					remote-endpoint = <&csi40_in>;
238 		i2c-mux {
239 			#address-cells = <1>;
240 			#size-cells = <0>;
243 				#address-cells = <1>;
244 				#size-cells = <0>;
251 				#address-cells = <1>;
252 				#size-cells = <0>;
259 				#address-cells = <1>;
260 				#size-cells = <0>;
267 				#address-cells = <1>;
268 				#size-cells = <0>;
283 				remote-endpoint = <&thc63lvd1024_in>;
290 	pinctrl-0 = <&scif_clk_pins>;
291 	pinctrl-names = "default";
330 	pinctrl-0 = <&qspi0_pins>;
331 	pinctrl-names = "default";
336 		compatible = "spansion,s25fs512s", "jedec,spi-nor";
338 		spi-max-frequency = <50000000>;
339 		spi-rx-bus-width = <4>;
342 			compatible = "fixed-partitions";
343 			#address-cells = <1>;
344 			#size-cells = <1>;
348 				read-only;
352 				read-only;
356 				read-only;
360 				read-only;
364 				read-only;
368 				read-only;
372 				read-only;
374 			uboot-env@700000 {
376 				read-only;
392 	timeout-sec = <60>;
397 	pinctrl-0 = <&scif0_pins>;
398 	pinctrl-names = "default";
404 	clock-frequency = <14745600>;