dts/qcom/sm7225-fairphone-fp4.dts

1 // SPDX-License-Identifier: BSD-3-Clause
6 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
13 #include <dt-bindings/input/input.h>
14 #include <dt-bindings/leds/common.h>
15 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
16 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
26 	chassis-type = "handset";
29 	qcom,msm-id = <434 0x10000>, <459 0x10000>;
30 	qcom,board-id = <8 32>;
38 		#address-cells = <2>;
39 		#size-cells = <2>;
42 		stdout-path = "serial0:115200n8";
45 			compatible = "simple-framebuffer";
54 	gpio-keys {
55 		compatible = "gpio-keys";
56 		pinctrl-names = "default";
57 		pinctrl-0 = <&gpio_keys_pin>;
59 		key-volume-up {
66 	reserved-memory {
73 			compatible = "qcom,rmtfs-mem";
75 			no-map;
77 			qcom,client-id = <1>;
82 	thermal-zones {
83 		chg-skin-thermal {
84 			polling-delay-passive = <0>;
85 			polling-delay = <0>;
86 			thermal-sensors = <&pm7250b_adc_tm 0>;
89 				active-config0 {
97 		conn-thermal {
98 			polling-delay-passive = <0>;
99 			polling-delay = <0>;
100 			thermal-sensors = <&pm7250b_adc_tm 1>;
103 				active-config0 {
114 	firmware-name = "qcom/sm7225/fairphone4/adsp.mdt";
119 	regulators-0 {
120 		compatible = "qcom,pm6350-rpmh-regulators";
121 		qcom,pmic-id = "a";
124 			regulator-min-microvolt = <1000000>;
125 			regulator-max-microvolt = <1200000>;
129 			regulator-min-microvolt = <1503000>;
130 			regulator-max-microvolt = <2048000>;
134 			regulator-min-microvolt = <1503000>;
135 			regulator-max-microvolt = <1980000>;
136 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
140 			regulator-min-microvolt = <2700000>;
141 			regulator-max-microvolt = <3300000>;
142 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
146 			regulator-min-microvolt = <352000>;
147 			regulator-max-microvolt = <801000>;
148 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
152 			regulator-min-microvolt = <1503000>;
153 			regulator-max-microvolt = <1980000>;
154 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
158 			regulator-min-microvolt = <1710000>;
159 			regulator-max-microvolt = <3544000>;
160 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
164 			regulator-min-microvolt = <1620000>;
165 			regulator-max-microvolt = <1980000>;
166 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
170 			regulator-min-microvolt = <2800000>;
171 			regulator-max-microvolt = <2800000>;
172 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
176 			regulator-min-microvolt = <1650000>;
177 			regulator-max-microvolt = <3401000>;
178 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
182 			regulator-min-microvolt = <1800000>;
183 			regulator-max-microvolt = <2000000>;
184 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
188 			regulator-min-microvolt = <1620000>;
189 			regulator-max-microvolt = <1980000>;
190 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
194 			regulator-min-microvolt = <570000>;
195 			regulator-max-microvolt = <650000>;
196 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
200 			regulator-min-microvolt = <1700000>;
201 			regulator-max-microvolt = <1900000>;
202 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
206 			regulator-min-microvolt = <1100000>;
207 			regulator-max-microvolt = <1305000>;
208 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
212 			regulator-min-microvolt = <830000>;
213 			regulator-max-microvolt = <921000>;
214 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
218 			regulator-min-microvolt = <788000>;
219 			regulator-max-microvolt = <1049000>;
220 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
224 			regulator-min-microvolt = <1080000>;
225 			regulator-max-microvolt = <1305000>;
226 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
230 			regulator-min-microvolt = <530000>;
231 			regulator-max-microvolt = <801000>;
232 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
236 			regulator-min-microvolt = <751000>;
237 			regulator-max-microvolt = <825000>;
238 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
242 			regulator-min-microvolt = <1080000>;
243 			regulator-max-microvolt = <1305000>;
244 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
248 	regulators-1 {
249 		compatible = "qcom,pm6150l-rpmh-regulators";
250 		qcom,pmic-id = "e";
253 			regulator-min-microvolt = <313000>;
254 			regulator-max-microvolt = <1395000>;
258 			regulator-min-microvolt = <1620000>;
259 			regulator-max-microvolt = <1980000>;
260 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
264 			regulator-min-microvolt = <1170000>;
265 			regulator-max-microvolt = <1305000>;
266 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
270 			regulator-min-microvolt = <1100000>;
271 			regulator-max-microvolt = <1299000>;
272 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
276 			regulator-min-microvolt = <1620000>;
277 			regulator-max-microvolt = <3300000>;
278 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
282 			regulator-min-microvolt = <1620000>;
283 			regulator-max-microvolt = <3300000>;
284 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
288 			regulator-min-microvolt = <1700000>;
289 			regulator-max-microvolt = <2950000>;
290 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
291 			regulator-allow-set-load;
292 			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
297 			regulator-min-microvolt = <2700000>;
298 			regulator-max-microvolt = <3544000>;
299 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
303 			regulator-min-microvolt = <1620000>;
304 			regulator-max-microvolt = <2000000>;
305 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
309 			regulator-min-microvolt = <2700000>;
310 			regulator-max-microvolt = <2960000>;
311 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
312 			regulator-allow-set-load;
313 			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
318 			regulator-min-microvolt = <3000000>;
319 			regulator-max-microvolt = <3401000>;
320 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
324 			regulator-min-microvolt = <3000000>;
325 			regulator-max-microvolt = <3401000>;
326 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
330 			regulator-min-microvolt = <1620000>;
331 			regulator-max-microvolt = <5492000>;
332 			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
333 			regulator-allow-bypass;
359 	firmware-name = "qcom/sm7225/fairphone4/cdsp.mdt";
372 	clock-frequency = <400000>;
382 	clock-frequency = <400000>;
389 	clock-frequency = <400000>;
399 		interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
400 		reset-gpios = <&tlmm 90 GPIO_ACTIVE_HIGH>;
402 		awinic,f0-preset = <2350>;
403 		awinic,f0-coefficient = <260>;
404 		awinic,f0-calibration-percent = <7>;
405 		awinic,drive-level = <125>;
407 		awinic,f0-detection-play-time = <5>;
408 		awinic,f0-detection-wait-time = <3>;
409 		awinic,f0-detection-repeat = <2>;
410 		awinic,f0-detection-trace = <15>;
412 		awinic,boost-debug = /bits/ 8 <0x30 0xeb 0xd4>;
414 		awinic,r-spare = /bits/ 8 <0x68>;
416 		awinic,bemf-upper-threshold = <4104>;
417 		awinic,bemf-lower-threshold = <1016>;
422 	qcom,gsi-loader = "self";
423 	memory-region = <&pil_ipa_fw_mem>;
424 	firmware-name = "qcom/sm7225/fairphone4/ipa_fws.mdt";
429 	firmware-name = "qcom/sm7225/fairphone4/modem.mdt";
436 	led-0 {
439 		led-sources = <1>;
440 		led-max-microamp = <180000>;
441 		flash-max-microamp = <1000000>;
442 		flash-max-timeout-us = <1280000>;
445 	led-1 {
448 		led-sources = <2>;
449 		led-max-microamp = <180000>;
450 		flash-max-microamp = <1000000>;
451 		flash-max-timeout-us = <1280000>;
456 	qcom,switching-freq = <800>;
457 	qcom,current-limit-microamp = <20000>;
458 	qcom,num-strings = <2>;
464 	gpio_keys_pin: gpio-keys-state {
467 		bias-pull-up;
468 		input-enable;
469 		power-source = <0>;
482 		qcom,hw-settle-time = <200>;
483 		qcom,pre-scaling = <1 1>;
490 		qcom,hw-settle-time = <200>;
491 		qcom,pre-scaling = <1 1>;
499 	charger-skin-therm@0 {
501 		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
503 		qcom,hw-settle-time-us = <200>;
506 	conn-therm@1 {
508 		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
510 		qcom,hw-settle-time-us = <200>;
522 		qcom,hw-settle-time = <200>;
523 		qcom,pre-scaling = <1 1>;
530 	 * Configure a bias-bus-hold on CTS to lower power
536 	bias-bus-hold;
541 	drive-strength = <2>;
542 	bias-disable;
547 	 * Configure a pull-up on RX. This is needed to avoid
549 	 * in tri-state (module powered off or not driving the
552 	bias-pull-up;
557 	drive-strength = <2>;
558 	bias-disable;
570 	sd-cd-pins {
573 		drive-strength = <2>;
574 		bias-disable;
579 	sd-cd-pins {
582 		drive-strength = <2>;
583 		bias-pull-up;
588 	vmmc-supply = <&vreg_l9e>;
589 	vqmmc-supply = <&vreg_l6e>;
591 	cd-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
597 	gpio-reserved-ranges = <13 4>, <56 2>;
599 	qup_uart1_sleep_cts: qup-uart1-sleep-cts-state {
603 		 * Configure a bias-bus-hold on CTS to lower power
609 		bias-bus-hold;
612 	qup_uart1_sleep_rts: qup-uart1-sleep-rts-state {
616 		 * Configure pull-down on RTS. As RTS is active low
621 		bias-pull-down;
624 	qup_uart1_sleep_rx: qup-uart1-sleep-rx-state {
628 		 * Configure a pull-up on RX. This is needed to avoid
632 		bias-pull-up;
635 	qup_uart1_sleep_tx: qup-uart1-sleep-tx-state {
639 		 * Configure pull-up on TX when it isn't actively driven
642 		bias-pull-up;
647 	/delete-property/ interrupts;
648 	interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
651 	pinctrl-names = "default", "sleep";
652 …pinctrl-1 = <&qup_uart1_sleep_cts>, <&qup_uart1_sleep_rts>, <&qup_uart1_sleep_tx>, <&qup_uart1_sle…
657 		compatible = "qcom,wcn3988-bt";
659 		vddio-supply = <&vreg_l11a>;
660 		vddxo-supply = <&vreg_l7a>;
661 		vddrf-supply = <&vreg_l2e>;
662 		vddch0-supply = <&vreg_l10e>;
663 		swctrl-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
665 		max-speed = <3200000>;
674 	reset-gpios = <&tlmm 156 GPIO_ACTIVE_LOW>;
676 	vcc-supply = <&vreg_l7e>;
677 	vcc-max-microamp = <800000>;
678 	vccq2-supply = <&vreg_l12a>;
679 	vccq2-max-microamp = <800000>;
685 	vdda-phy-supply = <&vreg_l18a>;
686 	vdda-pll-supply = <&vreg_l22a>;
696 	maximum-speed = "super-speed";
701 	vdd-supply = <&vreg_l18a>;
702 	vdda-pll-supply = <&vreg_l2a>;
703 	vdda-phy-dpdm-supply = <&vreg_l3a>;
709 	vdda-phy-supply = <&vreg_l22a>;
710 	vdda-pll-supply = <&vreg_l16a>;
716 	vdd-0.8-cx-mx-supply = <&vreg_l4a>;
717 	vdd-1.8-xo-supply = <&vreg_l7a>;
718 	vdd-1.3-rfa-supply = <&vreg_l2e>;
719 	vdd-3.3-ch0-supply = <&vreg_l10e>;
720 	vdd-3.3-ch1-supply = <&vreg_l11e>;