Lines Matching +full:tsens +full:- +full:v1
1 // SPDX-License-Identifier: GPL-2.0+
6 /dts-v1/;
9 #include <dt-bindings/usb/pd.h>
13 compatible = "fsl,imx8qxp-mek", "fsl,imx8qxp";
16 stdout-path = &lpuart0;
24 reg_usdhc2_vmmc: usdhc2-vmmc {
25 compatible = "regulator-fixed";
26 regulator-name = "SD1_SPWR";
27 regulator-min-microvolt = <3000000>;
28 regulator-max-microvolt = <3000000>;
30 enable-active-high;
33 gpio-sbu-mux {
34 compatible = "gpio-sbu-mux";
35 pinctrl-names = "default";
36 pinctrl-0 = <&pinctrl_typec_mux>;
37 select-gpios = <&lsio_gpio5 9 GPIO_ACTIVE_HIGH>;
38 enable-gpios = <&pca9557_a 7 GPIO_ACTIVE_LOW>;
39 orientation-switch;
43 remote-endpoint = <&typec_con_ss>;
54 pinctrl-names = "default";
55 pinctrl-0 = <&pinctrl_fec1>;
56 phy-mode = "rgmii-id";
57 phy-handle = <ðphy0>;
58 fsl,magic-packet;
62 #address-cells = <1>;
63 #size-cells = <0>;
65 ethphy0: ethernet-phy@0 {
66 compatible = "ethernet-phy-ieee802.3-c22";
73 #address-cells = <1>;
74 #size-cells = <0>;
75 clock-frequency = <100000>;
76 pinctrl-names = "default";
77 pinctrl-0 = <&pinctrl_lpi2c1 &pinctrl_ioexp_rst>;
80 i2c-mux@71 {
82 #address-cells = <1>;
83 #size-cells = <0>;
85 reset-gpios = <&lsio_gpio1 1 GPIO_ACTIVE_LOW>;
88 #address-cells = <1>;
89 #size-cells = <0>;
95 gpio-controller;
96 #gpio-cells = <2>;
101 #address-cells = <1>;
102 #size-cells = <0>;
107 #address-cells = <1>;
108 #size-cells = <0>;
111 pressure-sensor@60 {
118 #address-cells = <1>;
119 #size-cells = <0>;
125 gpio-controller;
126 #gpio-cells = <2>;
132 gpio-controller;
133 #gpio-cells = <2>;
136 light-sensor@44 {
137 pinctrl-names = "default";
138 pinctrl-0 = <&pinctrl_isl29023>;
141 interrupt-parent = <&lsio_gpio1>;
149 pinctrl-names = "default";
150 pinctrl-0 = <&pinctrl_typec>;
152 interrupt-parent = <&lsio_gpio1>;
157 remote-endpoint = <&usb3_drd_sw>;
162 compatible = "usb-c-connector";
163 label = "USB-C";
164 power-role = "source";
165 data-role = "dual";
166 source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
169 #address-cells = <1>;
170 #size-cells = <0>;
175 remote-endpoint = <&usb3_data_ss>;
185 pinctrl-names = "default";
186 pinctrl-0 = <&pinctrl_lpuart0>;
203 pmic-thermal {
204 polling-delay-passive = <250>;
205 polling-delay = <2000>;
206 thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
222 cooling-maps {
225 cooling-device =
236 assigned-clocks = <&clk IMX_SC_R_SDHC_0 IMX_SC_PM_CLK_PER>;
237 assigned-clock-rates = <200000000>;
238 pinctrl-names = "default";
239 pinctrl-0 = <&pinctrl_usdhc1>;
240 bus-width = <8>;
241 no-sd;
242 no-sdio;
243 non-removable;
248 assigned-clocks = <&clk IMX_SC_R_SDHC_1 IMX_SC_PM_CLK_PER>;
249 assigned-clock-rates = <200000000>;
250 pinctrl-names = "default";
251 pinctrl-0 = <&pinctrl_usdhc2>;
252 bus-width = <4>;
253 vmmc-supply = <®_usdhc2_vmmc>;
254 cd-gpios = <&lsio_gpio4 22 GPIO_ACTIVE_LOW>;
255 wp-gpios = <&lsio_gpio4 21 GPIO_ACTIVE_HIGH>;
269 usb-role-switch;
274 remote-endpoint = <&typec_dr_sw>;
281 compatible = "nxp,imx8qxp-vpu";
287 memory-region = <&decoder_boot>, <&decoder_rpc>;
293 memory-region = <&encoder_boot>, <&encoder_rpc>;